2011-2016 FJ Cruiser · Service Manual COMMUNICATION SYSTEM

TERMINALS OF ECU

System information · Vehicles built Aug 2009 – Oct 2010

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 from Aug 2012

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system is not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

    HINT:
    Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


CAN JUNCTION CONNECTOR

HINT:
  1. The connectors connected to the CAN J/C can be distinguished by the colors of the bus lines and the connecting side of the connector.
  2. E62, E63, E64 and E65 are interchangeable.

B125053E06
Text in Illustration 
*1
CAN Junction Connector
*2
CAN Junction Connector "B" Side (w/o Ground Terminal)
*3
CAN Junction Connector "A" Side (w/ Ground Terminal)
*4
Ground Terminal
Wiring Color 
CAN Junction Connector "A" Side (w/ Ground Terminal)
Wiring Color (CANH Side)
Wiring Color (CANL Side)
ECM (E62)
W
R
DLC3 (E63)
P
V
Steering angle sensor (E64)
B
Y
Yaw rate sensor (E65)
L
LG
Wiring Color 
CAN Junction Connector "B" Side (w/o Ground Terminal)
Wiring Color (CANH Side)
Wiring Color (CANL Side)
Skid control ECU (E66)
B
W

TERMINALS OF CONNECTORS FOR JUNCTION CONNECTOR (CAN JUNCTION CONNECTOR)
E191993E01
Terminal No.
Symbol
1
CANH
2
CANL
Text in Illustration 
*1
Front view of wire harness connector
(to CAN Junction Connector)

  1. Wiring diagram for identifying CAN junction connectors.
    C133802E02


DLC3
E191939E06
  1. Turn the ignition switch off.

    Text in Illustration 
    *1
    DLC3

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E1-6 (CANH) - E1-14 (CANL)
    P - V
    Ignition Switch off
    54 to 69 Ω
    E1-6 (CANH) - E1-4 (CG)
    P - W-B
    Ignition Switch off
    200 Ω or more
    E1-14 (CANL) - E1-4 (CG)
    V - W-B
    Ignition Switch off
    200 Ω or more
    E1-6 (CANH) - E1-16 (BAT)
    P - B-R
    Ignition Switch off
    6 kΩ or more
    E1-14 (CANL) - E1-16 (BAT)
    V - B-R
    Ignition Switch off
    6k Ω or more


BRAKE ACTUATOR (SKID CONTROL ECU)
E191994E01
  1. Turn the ignition switch off.

  2. Disconnect the A4 skid control ECU connector.

  3. Measure the resistance according to the value(s) in the table below.

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Brake Actuator (Skid Control ECU))
    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    A4-11 (CANH) - A4-25 (CANL)
    B - W
    Ignition Switch off
    54 to 69 Ω
    A4-11 (CANH) - A4-32 (GND2)
    B - W-B
    Ignition Switch off
    200 Ω or more
    A4-25 (CANL) - A4-32 (GND2)
    W - W-B
    Ignition Switch off
    200 Ω or more
    A4-11 (CANH) - A4-31 (+BS)
    B - Y
    Ignition Switch off
    6 kΩ or more
    A4-25 (CANL) - A4-31 (+BS)
    W - Y
    Ignition Switch off
    6 kΩ or more


ECM
  1. Turn the ignition switch off.

  2. Disconnect the E82, E81 and B50 ECM connectors.

  3. Measure the resistance according to the value(s) in the table below.
    E191996E01

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to ECM)
    -
    -
    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E81-32 (CANH) - E81-31 (CANL)
    W - R
    Ignition switch off
    108 to 132 Ω
    E81-32 (CANH) - B50-14 (E01)
    W - BR
    Ignition switch off
    200 Ω or more
    E81-31 (CANL) - B50-14 (E01)
    R - BR
    Ignition switch off
    200 Ω or more
    E81-32 (CANH) - E82-24 (BATT)
    W - L
    Ignition switch off
    6 kΩ or more
    E81-31 (CANL) - E82-24 (BATT)
    R - L
    Ignition switch off
    6 kΩ or more


YAW RATE SENSOR
C125958E08
  1. Turn the ignition switch off.

  2. Disconnect the E34 yaw rate sensor connector.

  3. Measure the resistance according to the value(s) in the table below.

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Yaw Rate Sensor)
    *2
    DLC3
    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E34-3 (CANH) - E34-2 (CANL)
    L - LG
    Ignition switch off
    54 to 69 Ω
    E34-3 (CANH) - E34-1 (GND)
    L - W-B
    Ignition switch off
    200 Ω or more
    E34-2 (CANL) - E34-1 (GND)
    LG - W-B
    Ignition switch off
    200 Ω or more
    E34-3 (CANH) - E1-16 (BAT)
    L - B-R
    Ignition switch off
    6 kΩ or more
    E34-2 (CANL) - E1-16 (BAT)
    LG - B-R
    Ignition switch off
    6 kΩ or more


STEERING ANGLE SENSOR
E192049E01
  1. Turn the ignition switch off.

  2. Disconnect the E16 steering angle sensor connector.

  3. Measure the resistance according to the value(s) in the table below.

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Steering Angle Sensor)
    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E16-3 (CANH) - E16-11 (CANL)
    B - Y
    Ignition switch off
    54 to 69 Ω
    E16-3 (CANH) - E16-2 (ESS)
    B - W-B
    Ignition switch off
    200 Ω or more
    E16-11 (CANL) - E16-2 (ESS)
    Y - W-B
    Ignition switch off
    200 Ω or more
    E16-3 (CANH) - E16-9 (BAT)
    B - W-R
    Ignition switch off
    6 kΩ or more
    E16-11 (CANL) - E16-9 (BAT)
    Y - W-R
    Ignition switch off
    6 kΩ or more

← TERMINALS OF ECU (Jul 2007 – Jul 2009)TERMINALS OF ECU (Nov 2010 – Jul 2011) →