2011-2016 FJ Cruiser · Service Manual COMMUNICATION SYSTEM

TERMINALS OF ECU

System information · Vehicles built Nov 2010 – Jul 2011

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 from Aug 2012

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system is not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
  4. Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


CAN JUNCTION CONNECTOR NO. 1 (for LHD)
E214894E01
Text in Illustration 
*a
to ECM
*b
to Yaw Rate Sensor
*c
to Combination Meter ECU
*d
to DLC3
*e
to Steering Angle Sensor
*f
to Skid Control ECU
Terminal No. (symbol)
Wiring color
Connect to
E95-1 (CANH)
LG-R
ECM
E95-12 (CANL)
LG-B
ECM
E95-2 (CANH)
LG
Yaw Rate Sensor
E95-13 (CANL)
L
Yaw Rate Sensor
E95-3 (CANH)
R
Combination Meter ECU
E95-14 (CANL)
W
Combination Meter ECU
E95-4 CANH)
P
DLC3
E95-15 (CANL)
V
DLC3
E95-5 (CANH)
L
Steering Angle Sensor
E95-16 (CANL)
W
Steering Angle Sensor
E95-6 (CANH)
B
Skid Control ECU
E95-17 (CANL)
W
Skid Control ECU

CAN JUNCTION CONNECTOR NO. 1 (for RHD)
E214894E02
Text in Illustration 
*a
to ECM
*b
to Yaw Rate Sensor
*c
to CAN Junction Connector No. 2
-
-
Terminal No. (symbol)
Wiring color
Connect to
E95-1 (CANH)
LG-R
ECM
E95-12 (CANL)
LG-B
ECM
E95-2 (CANH)
L
Yaw Rate Sensor
E95-13 (CANL)
LG
Yaw Rate Sensor
E95-3 (CANH)
R
CAN Junction Connector No. 2
E95-14 (CANL)
W
CAN Junction Connector No. 2

CAN JUNCTION CONNECTOR NO. 2 (for RHD)
E214893E03
Text in Illustration 
*a
to Steering Angle Sensor
*b
to DLC3
*c
to CAN Junction Connector No. 3
*d
to CAN Junction Connector No. 1
Terminal No. (symbol)
Wiring color
Connect to
E92-1 (CANH)
Y
CAN Junction Connector No. 3
E92-7 (CANL)
W
CAN Junction Connector No. 3
E92-2 CANH)
R
CAN Junction Connector No. 1
E92-8 (CANL)
W
CAN Junction Connector No. 1
E91-5 (CANH)
L
Steering Angle Sensor
E91-11 (CANL)
W
Steering Angle Sensor
E91-6 (CANH)
P
DLC3
E91-12 (CANL)
V
DLC3

CAN JUNCTION CONNECTOR NO. 3 (for RHD)
E214894E03
Text in Illustration 
*a
to Skid Control ECU
*b
to Combination Meter ECU
*c
to CAN Junction Connector No. 2
-
-
Terminal No. (symbol)
Wiring color
Connect to
A43-1 (CANH)
B
Skid Control ECU
A43-12 (CANL)
W
Skid Control ECU
A43-2 (CANH)
R
Combination Meter ECU
A43-13 (CANL)
W
Combination Meter ECU
A43-3 (CANH)
Y
CAN Junction Connector No. 2
A43-14 (CANL)
W
CAN Junction Connector No. 2

DLC3
E191939E07
  1. Turn the ignition switch off.

  2. Measure the resistance according to the value(s) in the table below.

    Text in Illustration 
    *a
    DLC3
    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E1-6 (CANH) - E1-14 (CANL)
    P - V
    Ignition switch off
    54 to 69 Ω
    E1-6 (CANH) - E1-4 (CG)
    P - W-B
    Ignition switch off
    200 Ω or more
    E1-14 (CANL) - E1-4 (CG)
    V - W-B
    Ignition switch off
    200 Ω or more
    E1-6 (CANH) - E1-16 (BAT)
    P - B-R
    Ignition switch off
    6 kΩ or more
    E1-14 (CANL) - E1-16 (BAT)
    V - B-R
    Ignition switch off
    6 kΩ or more


MASTER CYLINDER SOLENOID (SKID CONTROL ECU)
B255884E01
  1. Turn the ignition switch off.

  2. Disconnect the A4 master cylinder solenoid (skid control ECU) connector.

  3. Measure the resistance according to the value(s) in the table below.

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Master Cylinder Solenoid (Skid Control ECU))
    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    A4-11 (CANH) - A4-25 (CANL)
    B - W
    Ignition switch off
    54 to 69 Ω
    A4-11 (CANH) - A4-32 (GND2)
    B - W-B
    Ignition switch off
    200 Ω or higher
    A4-25 (CANL) - A4-32 (GND2)
    W - W-B
    Ignition switch off
    200 Ω or higher
    A4-11 (CANH) - A4-31 (+BS)
    B - Y
    Ignition switch off
    6 kΩ or higher
    A4-25 (CANL) - A4-31 (+BS)
    W - Y
    Ignition switch off
    6 kΩ or higher


ECM
E191996E03
Text in Illustration 
*a
Front view of wire harness connector
(to ECM)
-
-
  1. Turn the ignition switch off.

  2. Disconnect the E81, E82 and B50 ECM connectors.

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E81-32 (CANH) - E81-31 (CANL)
    LG-R - LG-B
    Ignition switch off
    108 to 132 Ω
    E81-32 (CANH) - B50-14 (E01)
    LG-R - BR
    Ignition switch off
    200 Ω or higher
    E81-31 (CANL) - B50-14 (E01)
    LG-B - BR
    Ignition switch off
    200 Ω or higher
    E81-32 (CANH) - E82-24 (BATT)
    LG-R - L
    Ignition switch off
    6 kΩ or higher
    E81-31 (CANL) - E82-24 (BATT)
    LG-B - L
    Ignition switch off
    6 kΩ or higher


YAW RATE SENSOR
E218497E01
  1. Turn the ignition switch off.

  2. Disconnect the E83 yaw rate sensor connector.

  3. Measure the resistance according to the value(s) in the table below.

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate Sensor)
    *b
    DLC3
    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E83-3 (CANH) - E83-2 (CANL)
    LG - L
    Ignition switch off
    54 to 69 Ω
    E83-3 (CANH) - E83-1 (GND)
    LG - W-B
    Ignition switch off
    200 Ω or higher
    E83-2 (CANL) - E83-1 (GND)
    L - W-B
    Ignition switch off
    200 Ω or higher
    E83-3 (CANH) - E1-16 (BAT)
    LG - B-R
    Ignition switch off
    6 kΩ or higher
    E83-2 (CANL) - E1-16 (BAT)
    L - B-R
    Ignition switch off
    6 kΩ or higher


STEERING ANGLE SENSOR
E192049E01
  1. Turn the ignition switch off.

  2. Disconnect the E16 steering angle sensor connector.

  3. Measure the resistance according to the value(s) in the table below.

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Steering Sensor)
    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E16-3 (CANH) - E16-11 (CANL)
    L - W
    Ignition switch off
    54 to 69 Ω
    E16-3 (CANH) - E16-2 (ESS)
    L - W-B
    Ignition switch off
    200 Ω or higher
    E16-11 (CANL) - E16-2 (ESS)
    W - W-B
    Ignition switch off
    200 Ω or higher
    E16-3 (CANH) - E16-9 (BAT)
    L - W-R
    Ignition switch off
    6 kΩ or higher
    E16-11 (CANL) - E16-9 (BAT)
    W - W-R
    Ignition switch off
    6 kΩ or higher


COMBINATION METER ASSEMBLY (COMBINATION METER ECU)
E214876E01
  1. Turn the ignition switch off.

  2. Disconnect the E13 and E14 combination meter assembly (combination meter ECU) connectors.

  3. Measure the resistance according to the value(s) in the table below.

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter Assembly (Combination Meter ECU))
    Standard Resistance 
    Terminal No. (symbol)
    Wiring color
    Switch Condition
    Specified Condition
    E14-10 (CANH) - E14-9 (CANL)
    R - W
    Ignition switch off
    54 to 69 Ω
    E14-10 (CANH) - E13-21 (ES)
    R - W-B
    Ignition switch off
    200 Ω or higher
    E14-9 (CANL) - E13-21 (ES)
    W - W-B
    Ignition switch off
    200 Ω or higher
    E14-10 (CANH) - E13-1 (B)
    R - R
    Ignition switch off
    6 kΩ or higher
    E14-9 (CANL) - E13-1 (B)
    W - R
    Ignition switch off
    6 kΩ or higher

← TERMINALS OF ECU (Aug 2009 – Oct 2010)TERMINALS OF ECU (Aug 2011 – Jul 2012) →