2011-2016 FJ Cruiser · Service Manual RESTRAINTS

B1655/37 Driver Side Seat Belt Buckle Switch Circuit Malfunction

Diagnostic trouble codes · Vehicles built Jul 2007 – Oct 2010

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012

DESCRIPTION

The driver side seat belt buckle switch circuit consists of the center airbag sensor assembly and the front seat inner belt assembly LH.
DTC B1655/37 is recorded when a malfunction is detected in the driver side seat belt buckle switch circuit.
DTC No.
DTC Detecting Condition
Trouble Area
B1655/37
  1. Center airbag sensor assembly detects line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in driver side seat belt buckle switch LH circuit for 2 seconds.
  2. Front seat inner belt assembly LH malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire No.2
  2. Front seat inner belt assembly LH
  3. Center airbag sensor assembly

WIRING DIAGRAM

C158843E04

INSPECTION PROCEDURE

NOTICE:
In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.

  1. Turn the ignition switch to the lock position.
  2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. Disconnect the connector from the center airbag sensor assembly.
  4. Disconnect the connectors from the steering pad.
  5. Disconnect the connectors from the front passenger airbag assembly.
  6. Disconnect the connector from the front seat outer belt assembly LH.
  7. Disconnect the connector from the front seat outer belt assembly RH.

    HINT:
    Skip the following steps if side and curtain shield airbags are not fitted.

  8. Disconnect the connector from the front seat side airbag assembly LH.
  9. Disconnect the connector from the front seat side airbag assembly RH.
  10. Disconnect the connector from the curtain shield airbag assembly LH.
  11. Disconnect the connector from the curtain shield airbag assembly RH.

1. CHECK DTC (CENTER AIRBAG SENSOR ASSEMBLY)
H100892E01
  1. Turn the ignition switch on, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1655/37 is not output.

    HINT:
    DTCs other than DTC B1655/37 may be output at this time, but they are not related to this check.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)

2. CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the front seat inner belt assembly LH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


3. CHECK FLOOR WIRE NO.2

  1. H100893E02
    Check for open in the circuit.
    1. Disconnect the connectors from the center airbag sensor assembly and the front seat inner belt assembly LH.

    2. Using a service wire, connect L1-11 (DBE+) and L1-12 (DBE-) of connector B.

      NOTICE:
      Do not forcibly insert the service wire into the terminals of the connector when connecting.

    3. Measure the resistance.

      Standard resistance:
      Tester connection
      Condition
      Specified Condition
      L17-1 (LBE+) - L17-3 (LBE-)
      Always
      Below 1 Ω

  1. H100159E02
    Check for short in the circuit.
    1. Disconnect the service wire from connector B.

    2. Measure the resistance.

      Standard resistance:
      Tester connection
      Condition
      Specified Condition
      L17-1 (LBE+) - L17-3 (LBE-)
      Always
      1 MΩ or higher

  1. Check for short to ground in the circuit.

    1. Measure the resistance.

      Standard resistance:
      Tester connection
      Condition
      Specified Condition
      L17-1 (LBE+) - Body ground
      Always
      1 MΩ or higher
      L17-3 (LBE-) - Body ground
      Always
      1 MΩ or higher

  1. Check for short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch on.

    3. Measure the voltage.

      Standard voltage:
      Tester connection
      Switch Condition
      Specified Condition
      L17-1 (LBE+) - Body ground
      Ignition switch on
      Below 1 V
      L17-3 (LBE-) - Body ground
      Ignition switch on
      Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.



NG
REPAIR OR REPLACE FLOOR WIRE NO.2
OK


4. CHECK FRONT SEAT INNER BELT ASSEMBLY LH
H100892E01
  1. Connect the connectors to the center airbag sensor assembly and the front seat inner belt assembly LH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1655/37 is not output.

    HINT:
    DTCs other than DTC B1655/37 may be output at this time, but they are not related to this check.



NG
Go to step 5
OK

USE SIMULATION METHOD TO CHECK (Click here)

5. REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the front seat inner belt assembly LH (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle if possible.


NEXT


6. CHECK CENTER AIRBAG SENSOR ASSEMBLY
H100892E01
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1655/37 is not output.

    HINT:
    DTCs other than DTC B1655/37 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

END


← B1653/35 Seat Position Airbag Sensor Circuit Malfunction (from Aug 2012)B1655/37 Driver Side Seat Belt Buckle Switch Circuit Malfunction (Nov 2010 – Jul 2012) →