2011-2016 FJ Cruiser · Service Manual BRAKE

C1249/49 Open in Stop Light Switch Circuit

Diagnostic trouble codes · Vehicles built Jul 2007 – Oct 2010

DESCRIPTION

The skid control ECU inputs the stop light switch signal and detects the status of the brake operation.
DTC No.
DTC Detecting Condition
Trouble Areas
C1249/49
When ECU terminal IG1 voltage 9.5 V to 17.0 V and ABS non-operational, open in stop light switch circuit continues for 0.3 seconds or more.
  1. Stop light switch assembly
  2. Stop light switch circuit
  3. Master cylinder solenoid (skid control ECU)

WIRING DIAGRAM

C164942E01

INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration (Click here).


1. CHECK STOP LIGHT SWITCH OPERATION
  1. Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

    OK:
    Pedal condition
    Illumination Condition
    Brake pedal depressed
    ON
    Brake pedal released
    OFF

    HINT:
    Check the stop light bulbs as they may have burnt out.



NG
Go to step 4
OK


2. INSPECT SKID CONTROL ECU (STP TERMINAL VOLTAGE)

  1. C121700E53
    Disconnect the skid control ECU connector.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A4-7 (STP) - Body ground
    Stop light switch ON
    (Brake pedal depressed)
    8 to 14 V
    A4-7 (STP) - Body ground
    Stop light switch OFF
    (Brake pedal released)
    Below 1.5 V


    Result:
    Result
    Proceed to
    OK (When troubleshooting in accordance with DTC CHART)
    A
    OK (When troubleshooting in accordance with PROBLEM SYMPTOMS TABLE)
    B
    NG
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


3. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Check if the same DTC is detected (Click here).

    Result:
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE MASTER CYLINDER SOLENOID (Click here)

4. INSPECT STOP LIGHT SWITCH ASSEMBLY

  1. I038520E05
    Disconnect the stop light switch connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Switch pin released
    Below 1 Ω
    3 - 4
    Switch pin released
    10 kΩ or higher
    1 - 2
    Switch pin pushed in
    10 kΩ or higher
    3 - 4
    Switch pin pushed in
    Below 1 Ω



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STOP LIGHT SWITCH)

  1. C121702E06
    Disconnect the skid control ECU connector.

  1. Disconnect the stop light switch connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    A4-45 (STP2) - A3-1
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Check if the same DTC is detected (Click here).

    Result:
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE MASTER CYLINDER SOLENOID (Click here)


← C1248/48 Open Circuit in Rear Differential Lock (Jul 2007 – Oct 2010)C1251 Open in Pump Motor Circuit (Nov 2010 – Jul 2012) →