2011-2016 FJ Cruiser · Service Manual TRANSMISSION

P0746 Pressure Control Solenoid "A" Performance (Shift Solenoid Valve SL1)

Diagnostic trouble codes · Vehicles built Nov 2010 – Jul 2011

Also covers:

Versions by build date: Dec 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 Aug 2012 – Jul 2014 from Aug 2014

DESCRIPTION

The ECM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear position (1st, 2nd, 3rd, 4th or 5th gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of the shift solenoid valves, valve body or automatic transmission (clutch, brake or gear, etc.).
DTC No.
DTC Detection Condition
Trouble Area
P0746
The gear required by the ECM does not match the actual gear when driving (2-trip detection logic)
  1. Shift solenoid valve SR remains open or closed
  2. Shift solenoid valve SL1 remains closed
  3. Shift solenoid valve SLT remains open or closed
  4. Valve body is blocked
  5. Automatic transmission (clutch, brake or gear, etc.)
P0771
The gear required by the ECM does not match the actual gear when driving (2-trip detection logic*1, 1-trip detection logic*2)
  1. Shift solenoid valve SR remains open or closed
  2. Shift solenoid valve SL1 remains closed
  3. Shift solenoid valve SLT remains open or closed
  4. Valve body is blocked
  5. Automatic transmission (clutch, brake or gear, etc.)

HINT:
  1. *1: w/ OBD
  2. *2: w/o OBD


MONITOR DESCRIPTION

This DTC indicates stuck ON malfunction or stuck OFF malfunction of the shift solenoid valve SR or SL1. The ECM controls the gearshifts by turning the shift solenoid valves ON/OFF. When the gear position directed by the ECM and the actual gear position do not match, the ECM stores the DTCs.

INSPECTION PROCEDURE

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.
  2. Turn the ignition switch off.
  3. Connect the intelligent tester to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the tester on.
  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.
  7. According to the display on the tester, perform the Active Test.

HINT:
While driving, the shift position can be changed with the intelligent tester.
Comparing the shift position directed by the Active Test with the actual shift position enables the problem to be confirmed (Click here).
Engine and ECT 
Tester Display
Test Part
Control Range
Diagnostic Note
Control the Shift Position
Operate shift solenoid valve and set each shift position by yourself
  1. Press "→" button: Shift up
  2. Press "←" button: Shift down
Possible to check operation of shift solenoid valves
[Vehicle Condition]
50 km/h (30 mph) or less


HINT:
  1. This test can be conducted when the vehicle speed is 50 km/h (30 mph) or less.
  2. The 4th to 5th up-shifting must be performed with the accelerator pedal released.
  3. The 5th to 4th down-shifting must be performed with the accelerator pedal released.
  4. Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
  5. The shift position directed by the ECM is shown in the Data List / Shift Status display on the intelligent tester.
  6. The shift solenoid valve SR and SL1 are turned on/off normally when the shift lever is in D:
Gearshift controlled by ECM
1st
2nd
3rd
4th
5th
Shift solenoid valve SR
OFF
OFF
OFF
OFF
ON
Shift solenoid valve SL1
OFF
OFF
OFF
OFF
ON


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTCS P0746 AND P0771)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs using the intelligent tester.

    Result 
    Result
    Proceed to
    Only P0746 and P0771 are output
    Only DTC P0771 is output
    A
    P0746, P0771 and other DTCs are output
    B

HINT:
If any codes besides P0746 and P0771 are output, perform troubleshooting for those DTCs first



B
GO TO DTC CHART (Click here)
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVE THE SOLENOID (SLT))
G020657E01

NOTICE:
  1. Perform the test at the normal operating ATF (Automatic Transmission Fluid) temperature: 50 to 80°C (122 to 176°F).
  2. Be careful to prevent SST hose from interfering with the exhaust pipe.
  3. Perform the test with the A/C off.

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Remove the test plug on the transmission case center right side and connect SST.

SST
09992-00095   (09992-00231, 09992-00271)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and warm it up.

  1. Measure the line pressure with SST.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  1. According to the display on the tester, perform the Active Test.

  1. Measure the line pressure with SST.

    Engine and ECT 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Active the Solenoid (SLT)*
    Operate the shift solenoid SLT and raise line pressure
    ON or OFF

    HINT:
    1. OFF: Line pressure up (when Active Test "Active the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn OFF)
    2. ON: No action (normal operation)

    [Vehicle Condition]
    1. Vehicle stopped
    2. Engine idling
    *: Active the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Click here) as well. Please note that the pressure values in the Active Test and Hydraulic Test are different.

    OK:
    The line pressure changes as specified when performing the Active Test.



NG
REPLACE SHIFT SOLENOID VALVE SLT (Click here)
OK


3. INSPECT SHIFT SOLENOID VALVE SL1

  1. C204845E01
    Remove the shift solenoid valve SL1.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

    Text in Illustration 
    *1
    Component without harness connected:
    (Shift Solenoid Valve SL1)

  1. Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

    OK:
    The solenoid makes operating sounds.



NG
REPLACE SHIFT SOLENOID VALVE SL1 (Click here)
OK


4. INSPECT SHIFT SOLENOID VALVE SR

  1. A110988E17
    Remove the shift solenoid valve SR.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - Solenoid body
    20°C (68°F)
    11 to 15 Ω

    Text in Illustration 
    *1
    Component without harness connected:
    (Shift Solenoid Valve SR)

  1. Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.

    OK:
    The solenoid makes operating sounds



NG
REPLACE SHIFT SOLENOID VALVE SR (Click here)
OK


5. INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly.

    HINT:
    Refer to Problem Symptoms Table Chapter 2 (Click here).

    OK:
    There are no foreign objects on any valves and they operate smoothly.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY (Click here)


← P0746 Pressure Control Solenoid "A" Performance (Shift Solenoid Valve SL1) (+ P0771) (Aug 2009 – Oct 2010)P0746 Pressure Control Solenoid "A" Performance (Shift Solenoid Valve SL1) (+ P0771) (Aug 2011 – Jul 2012) →