2011-2016 FJ Cruiser · Service Manual TRANSMISSION

P2714 Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT)

Diagnostic trouble codes · Vehicles built Jul 2007 – Nov 2007

Versions by build date: Jul 2007 – Nov 2007 from Aug 2009

DESCRIPTION

C221301E04
Shift solenoid valve SLT controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and vehicle speed sensor. The ECM adjusts the current to shift solenoid valve SLT to control the hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.
DTC No.
DTC Detection Condition
Trouble Area
P2714
ECM detects malfunctions on SLT (ON side) according to the revolution difference between the turbine and the output shaft, and also by monitoring the oil pressure. (1-trip detection logic)
  1. Shift solenoid valve SLT remains open or closed
  2. Shift solenoid valve S1, S2, SR, SL1 or SL2 remains open or closed
  3. Valve body is blocked
  4. Automatic transmission (clutch, brake or gear, etc.)

MONITOR DESCRIPTION

The ECM calculates the amount of heat absorbed by the friction material based on the difference in revolution (clutch slippage) between the turbine and output shaft. The ECM outputs this DTC when the amount of heat absorption exceeds the specified value.
When the shift solenoid valve SLT remains on, the oil pressure goes down and the clutch engagement force decreases.
NOTE: If driving continues under these conditions, the clutch will burn out and the vehicle will no longer be drivable.

INSPECTION PROCEDURE


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2714)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs using the intelligent tester.

    Result: 
    Display (DTC Output)
    Proceed to
    Only "P2714" is output
    A
    "P2714" and other DTCs
    B

    HINT:
    If any codes besides "P2714" are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SHIFT SOLENOID VALVE SLT)
G020657E01

NOTICE:
  1. Perform the test at the normal operating ATF (Automatic Transmission Fluid) temperature: 50 to 80°C (122 to 176°F).
  2. Be careful to prevent SST's hose from interfering with the exhaust pipe.
  3. Perform the test with the A/C OFF.

HINT:
Performing a intelligent tester Active Test allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time.
The Data List can be displayed during the Active Test.

  1. Remove the test plug on the transmission case center right side and connect SST.

SST
09992-00095   (09992-00231, 09992-00271)
  1. Connect a intelligent tester to the DLC3.

  1. Start the engine and warm it up.

  1. Measure the line pressure with SST.

  1. Turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  1. According to the display on the tester, perform the Active Test.

  1. Measure the line pressure with SST.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Active the Solenoid (SLT)*
    Operate the shift solenoid SLT and raise line pressure
    ON or OFF

    HINT:
    1. OFF: Line pressure up (when Active Test "Active the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn OFF)
    2. ON: No action (normal operation)

    [Vehicle Condition]
    1. Vehicle stopped
    2. Engine idling
    *: Active the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the HYDRAULIC TEST (Click here) as well. Please note that the pressure values in the Active Test and HYDRAULIC TEST are different.



NG
Go to step 9
OK


3. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SHIFT)

HINT:
Performing the Active Test using a intelligent tester allows components, such as the relay, VSV, and actuator, to be operated without removing any parts. Performing the Active Test as a first step of troubleshooting is one method of shortening labor time.
It is possible to display the Data List during the Active Test.
  1. Warm up the engine.
  2. Turn the ignition switch to OFF.
  3. Connect the intelligent tester to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the tester ON.
  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.
  7. According to the display on the tester, perform the Active Test.

HINT:
While driving, the shift position can be changed with the intelligent tester.
Comparing the shift position directed by the Active Test with the actual shift position enables the problem to be confirmed (Click here).

Tester Display
Test Part
Control Range
Diagnostic Note
Control the Shift Position
Operate shift solenoid valve and set each shift position by yourself
  1. Press "→" button: Shift up
  2. Press "←" button: Shift down
Possible to check operation of shift solenoid valves
[Vehicle Condition]
50 km/h (30 mph) or less

HINT:
  1. This test can be conducted when the vehicle speed is 50 km/h (30 mph) or less.
  2. The 4th to 5th up-shifting must be performed with the accelerator pedal released.
  3. The 5th to 4th down-shifting must be performed with the accelerator pedal released.
  4. Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
  5. The shift position directed by the ECM is shown in the Data List / Shift Status display on the intelligent tester.

  1. Compare the ECM gear shift command and the actual gear position.

    ECM gear shift command
    1st
    2nd
    3rd
    4th
    5th
    Proceed to
    Actual gear position under malfunction
    Shift solenoid S1
    Stuck ON
    1st
    2nd
    2nd
    1st
    N*1
    A
    Stuck OFF
    4th
    3rd
    3rd
    4th
    5th
    Shift solenoid S2
    Stuck ON*2
    2nd
    2nd
    3rd
    3rd
    N*1
    B
    Stuck OFF*3
    1st
    1st
    4th
    4th
    5th
    Shift solenoid SL2
    Stuck ON
    1st
    2nd
    3rd
    4th
    N*1
    C
    Stuck OFF
    1st
    2nd
    3rd
    4th
    5th
    Shift solenoid SR
    Stuck ON*4
    1st
    2nd
    3rd
    4th
    5th
    D
    Stuck OFF*5
    1st
    2nd
    3rd
    4th
    4th

    HINT:
    1. *1: Neutral
    2. *2: When shift solenoid S2 is stuck ON, the vehicle cannot drive in reverse.
    3. *3: When shift solenoid S2 is stuck OFF, the 4th to 5th up-shift will have a large shift shock. Also the 5th to 4th down-shift will have time lag.
    4. *4: Stuck ON condition can be determined by checking if shift shock has increased excessively.
    5. *5: When shift solenoid SR is stuck OFF, moving the shift lever from N to D will cause a large shift shock.
    6. Gear shift can be determined by paying attention to changes in rpm.



B
Go to step 5

C
Go to step 6

D
Go to step 7

OK
Go to step 9
A


4. INSPECT SHIFT SOLENOID VALVE S1

  1. A110986E04
    Remove the shift solenoid valve S1.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    Solenoid Connector (S1) - Solenoid Body (S1)
    11 to 15 Ω at 20°C (68°F)

  1. Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.

    OK:
    The solenoid makes operating sounds.



OK
Go to step 10
NG

REPLACE SHIFT SOLENOID VALVE S1 (Click here)

5. INSPECT SHIFT SOLENOID VALVE S2

  1. A110987E04
    Remove the shift solenoid valve S2.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    Solenoid Connector (S2) - Solenoid Body (S2)
    11 to 15 Ω at 20°C (68°F)

  1. Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.

    OK:
    The solenoid makes operating sounds.



OK
Go to step 10
NG

REPLACE SHIFT SOLENOID VALVE S2 (Click here)

6. INSPECT SHIFT SOLENOID VALVE SL2

  1. G020767E39
    Remove the shift solenoid valve SL2.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    1 - 2
    5.0 to 5.6 Ω at 20°C (68°F)

  1. Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

    OK:
    The solenoid makes operating sounds.



OK
Go to step 10
NG

REPLACE SHIFT SOLENOID VALVE SL2 (Click here)

7. INSPECT SHIFT SOLENOID VALVE SR

  1. A110988E05
    Remove the shift solenoid valve SR.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    Solenoid Connector (SR) - Solenoid Body (SR)
    11 to 15 Ω at 20°C (68°F)

  1. Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.

    OK:
    The solenoid makes operating sounds.



NG
REPLACE SHIFT SOLENOID VALVE SR (Click here)
OK


8. INSPECT SHIFT SOLENOID VALVE SL1

  1. G020767E38
    Remove the shift solenoid valve SL1.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    1 - 2
    5.0 to 5.6 Ω at 20°C (68°F)

  1. Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

    OK:
    The solenoid makes operating sounds.



OK
Go to step 10
NG

REPLACE SHIFT SOLENOID VALVE SL1 (Click here)

9. INSPECT SHIFT SOLENOID VALVE SLT

  1. G020767E42
    Remove the shift solenoid valve SLT.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    1 - 2
    5.0 to 5.6 Ω at 20°C (68°F)

  1. Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

    OK:
    The solenoid makes operating sounds.



NG
REPLACE SHIFT SOLENOID VALVE SLT (Click here)
OK


10. INSPECT TRANSMISSION VALVE BODY ASSEMBLY (See chapter 2 in the problem symptoms table)

OK:
There are no foreign objects on any valves and they operate smoothly.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK


11. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
  1. Check the torque converter clutch assembly (Click here).

    OK:
    The torque converter clutch operates normally.



NG
REPLACE TORQUE CONVERTER CLUTCH ASSEMBLY (Click here)
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY (Click here)


← P0985 Shift Solenoid "E" Control Circuit Low (Shift Solenoid Valve SR) (+ P0986) (from Aug 2009)P2714 Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT) (from Aug 2009) →