2011-2016 FJ Cruiser · Service Manual TRANSMISSION

P0710 Transmission Fluid Temperature Sensor "A" Circuit

Diagnostic trouble codes · Vehicles built Jul 2007 – Jul 2009

Also covers:

DESCRIPTION

G031389E11
The ATF (Automatic Transmission Fluid) temperature sensor converts the fluid temperature into a resistance value which is input into the ECM.
The ECM applies a voltage to the temperature sensor through ECM terminal THO1.
The sensor resistance changes with the transmission fluid temperature. As the temperature becomes higher, the sensor resistance decreases.
One terminal of the sensor is grounded so that the sensor resistance and the voltage decrease as the temperature becomes higher.
The ECM calculates the fluid temperature based on the voltage signal.
DTC No.
DTC Detection Conditions
Trouble Areas
P0710
(a) and (b) are detected momentarily within 0.5 seconds when neither P0712 nor P0713 is detected. (1-trip detection logic)
  1. (a) No. 1 ATF temperature sensor resistance is less than 79 Ω.
  2. (b) No. 1 ATF temperature sensor resistance is more than 156 kΩ.

HINT:
Within 0.5 seconds, the malfunction changes from (a) to (b) or from (b) to (a).

  1. Open or short in No. 1 ATF temperature sensor circuit
  2. Transmission wire (No. 1 ATF temperature sensor)
  3. ECM
P0712
No. 1 ATF temperature sensor resistance is less than 79 Ω for 0.5 seconds or more. (1-trip detection logic)
  1. Short in No. 1 ATF temperature sensor circuit
  2. Transmission wire (No. 1 ATF temperature sensor)
  3. ECM
P0713
No. 1 ATF temperature sensor resistance is more than 156 kΩ for 0.5 seconds or more 15 minutes or more after starting engine. (1-trip detection logic)
  1. Open in No. 1 ATF temperature sensor circuit
  2. Transmission wire (No. 1 ATF temperature sensor)
  3. ECM

MONITOR DESCRIPTION

These DTCs indicate an open or short in the Automatic Transmission Fluid (ATF) temperature sensor circuit.
The ATF temperature sensor converts ATF temperature to an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature, and detects any open or short malfunctions in the ATF temperature circuit. If the resistance value of the ATF temperature is less than 79 Ω*1 or more than 156 kΩ*2, the ECM interprets this as a fault in the ATF sensor or its wiring. The ECM turns on the MIL and stores a DTC.
*1: 150°C (302°F) or more is indicated regardless of the actual ATF temperature.
*2: -40°C (-40°F) is indicated regardless of the actual ATF temperature.

HINT:
The ATF temperature can be checked on a intelligent tester display.


WIRING DIAGRAM

C166894E01

INSPECTION PROCEDURE

HINT:
According to the Data List displayed on a intelligent tester, you can read the values of components, such as the switches, sensors and actuators, without removing any parts. Reading the Data List as a first step of troubleshooting is one method of shortening labor time.

NOTICE:
In the table below, the values listed under "Normal Condition" are for reference only. Do not depend solely on these reference values when judging whether a part is faulty or not.

  1. Warm up the engine.
  2. Turn the ignition switch to OFF.
  3. Connect the intelligent tester to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the tester ON.
  6. Enter the following menus: Powertrain / Engine and ECT / Data List.
  7. According to the display on the tester, read the Data List.
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
A/T Oil Temperature 1
No. 1 ATF Temperature Sensor Value/
min.: -40°C (-40°F)
max.: 215°C (419°F)
  1. After Stall Test:
    Approximately 80°C (176°F)
  2. Equal to ambient temperature during cold soak
If the value is "-40°C (-40°F)" or "150°C (302°F) or more", No. 1 ATF temperature sensor circuit is open or short.

HINT:
When DTC P0712 is output and intelligent tester reading is 150°C (302°F) or more, there is a short circuit.
When DTC P0713 is output and intelligent tester reading is -40°C (-40°F), there is an open circuit.
Measure the resistance between terminal THO1 and the body ground.

Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
150°C (302°F) or more
Short circuit

HINT:
If a circuit related to the ATF temperature sensor becomes open, P0713 is immediately set (in 0.5 seconds). When P0713 is set, P0711 cannot be detected.
It is not necessary to inspect the circuit when P0711 is set.


1. INSPECT TRANSMISSION WIRE (ATF TEMPERATURE SENSOR)

  1. C110342E77
    Disconnect the transmission wire connector from the transmission.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    2 (OT-) - 10 (OT+)
    79 Ω to 156 kΩ

  1. Measure the resistance.

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    2 (OT-) - Body ground
    10 kΩ or higher
    10 (OT+) - Body ground
    10 kΩ or higher

HINT:
If the resistance is outside the specified range at either of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.

ATF Temperature
Specified Condition
20°C (68°F)
3 to 5 kΩ
110°C (230°F)
0.22 to 0.28 kΩ


NG
REPAIR OR REPLACE TRANSMISSION WIRE (Click here)
OK


2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

  1. A107751E05
    Connect the transmission wire connector to the transmission.

  1. Disconnect the ECM connectors.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    B2-24 (THO1) - B1-28 (E2)
    79 Ω to 156 kΩ

  1. Measure the resistance.

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    B2-24 (THO1) - Body ground
    10 kΩ or higher
    B1-28 (E2) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) (from Aug 2014)P0711 Transmission Fluid Temperature Sensor "A" Performance (Dec 2007 – Jul 2009) →