P0711 Transmission Fluid Temperature Sensor "A" Performance
Diagnostic trouble codes · Vehicles built Dec 2007 – Jul 2009
Versions by build date: Dec 2007 – Jul 2009 Aug 2009 – Jul 2011 Aug 2011 – Jul 2012 Aug 2012 – Jul 2014 from Aug 2014
DESCRIPTION
Refer to DTC P0710 (Click here).| DTC No. |
DTC Detection Condition |
Trouble Areas |
| P0711 |
Either of the following Condition (A) or (B) is met: Condition (A): All of (a) and (b) are detected (2-trip detection logic):
Both (a) and (b) are detected (2-trip detection logic)
|
Transmission wire (No. 1 ATF temperature sensor) |
MONITOR DESCRIPTION
This DTC indicates that there is a problem with the output from the ATF (Automatic Transmission Fluid) temperature sensor and that the sensor itself is defective. The ATF temperature sensor converts the ATF temperature to an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature and detects any open or short malfunctions in the ATF temperature circuit or a fault of the ATF temperature sensor.After running the vehicle for a certain period, the ATF temperature should increase. If the ATF temperature is below 20°C (68°F) after running the vehicle for a certain period, the ECM interprets this as a fault, and turns on the MIL.
When the ATF temperature is 110°C (230°F) or more and engine coolant temperature reaches 60°C (140°F) after cold start, the ECM also determines this as a fault, turns on the MIL, and stores the DTC.
INSPECTION PROCEDURE
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are for reference only. Do not depend solely on these reference values when judging whether a part is faulty or not.
- Warm up the engine.
- Turn the ignition switch off.
- Connect the intelligent tester to the DLC3.
- Turn the ignition switch to ON.
- Turn the tester ON.
- Enter the following menus: Powertrain / Engine and ECT / Data List.
- According to the display on the tester, read the Data List.
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
A/T Oil Temperature 1
No. 1 ATF Temperature Sensor Value/
min.: -40°C (-40°F)
max.: 215°C (419°F)
- After Stall Test:
Approximately 80°C (176°F)
- Equal to ambient temperature during cold soak
If the value is "-40°C (-40°F)" or "150°C (302°F) or more", No. 1 ATF temperature sensor circuit is open or short.
- HINT:
- When DTC P0712 is output and the intelligent tester reading is 150°C (302°F) or more, there is a short circuit.
- When DTC P0713 is output and the intelligent tester reading is -40°C (-40°F), there is an open circuit.
- Measure the resistance between terminal THO1 and the body ground.
Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
150°C (302°F) or more
Short circuit
- After Stall Test:
- HINT:
- If a circuit related to the ATF temperature sensor becomes open, P0713 is immediately stored (in 0.5 seconds). When P0713 is stored, P0711 cannot be detected.
- It is not necessary to inspect the circuit when P0711 is stored.
| 1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0711) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the intelligent tester.
Result Result
Proceed to
Only "P0711" is output
A
"P0711" and other DTCs are output
B
- HINT:
- If any codes besides "P0711" are output, perform troubleshooting for those DTCs first.
|
|
||||
| A | |
| 2. CHECK TRANSMISSION FLUID LEVEL |
- OK:
- Automatic transmission fluid level is correct.
|
|
||||
| OK | ||
| ||
