2011-2016 FJ Cruiser · Service Manual TRANSMISSION

P2740 Transmission Fluid Temperature Sensor "B" Circuit

Diagnostic trouble codes · Vehicles built Jul 2007 – Jul 2009

Also covers:

DESCRIPTION

The No. 2 Automatic Transmission Fluid (ATF) temperature sensor is on the transmission, just before the oil cooler inlet pipeline.
If the ECM detects an abnormally high ATF temperature through this sensor, it illuminates the warning light to indicate the problem to the driver.

HINT:
  1. The ATF temperature is liable to increase under vehicle conditions such as towing, climbing hills and in traffic.
  2. If there is a short malfunction in the No. 2 ATF temperature sensor, the ECM receives signals from the sensor, which indicate that the ATF temperature is 150°C (302°F) or more.
    The symptoms and recovery conditions, when the sensor is normal or there is a short malfunction in the sensor, are as shown in the table below. 
    No.2 ATF Temperature Sensor Status
    Detection Condition
    Symptom
    Recovery Condition
    Sensor is normal
    1. ATF temperature more than 150°C (302°F)
    1. ATF temperature warning light remains on
    1. ATF temperature less than 135°C (275°F) *2
    1. ATF temperature more than 130°C (266°F)
    1. Shift point too high
    1. ATF temperature less than 110°C (230°F)
    When the conditions (a) and (b) are satisfied continually
    1. (a) ATF temperature more than130°C (266°F)
    2. (b) Engine coolant temperature more than 95°C (203°F)
    1. Lock-up in 3rd gear *1
    1. ATF temperature less than 110°C (230°F) *2 and engine coolant temperature less than 95°C (203°F)
    Sensor is short
    1. Any conditions
    1. ATF temperature warning light remains on
    2. Shift point too high
    1. Symptoms still occur
    1. Engine coolant temperature more than 95°C (203°F)
    1. Lock-up in 3rd gear *1
    1. Symptom still occurs

HINT:
*1: When the ATF temperature is normal, the transmission locks up in 5th gear with the shift lever in the D position and in 4th gear with the shift lever in the 4th position.
*2: When the ATF temperature is in the normal range, it decreases to less than 135°C (275°F) within 5 minutes of the shift lever being moved to the P or N position, while idling.

DTC No.
DTC Detection Conditions
Trouble Areas
P2740
Conditions (a) and (b) are detected momentarily within 0.5 seconds when neither P2742 nor P2743 is detected. (1-trip detection logic)
  1. (a) No. 2 ATF temperature sensor resistance (voltage) is less than 25 Ω (0.046 V).
  2. (b) No. 2 ATF temperature sensor resistance (voltage) is more than 156 kΩ (4.915 V).

HINT:
Within 0.5 seconds the malfunction changes from (a) to (b) or (b) to (a).

  1. Open or short in No.2 ATF temperature sensor circuit
  2. No.2 ATF temperature sensor
  3. ECM
P2742
No. 2 ATF temperature sensor resistance (voltage) is less than 25 Ω (0.046 V) for 0.5 seconds or more (1-trip detection logic)
  1. Short in No.2 ATF temperature sensor circuit
  2. No.2 ATF temperature sensor
  3. ECM
P2743
No. 2 ATF temperature sensor resistance (voltage) is more than 156 kΩ (4.915 V) for 0.5 seconds or more 15 minutes or more after starting engine (1-tip detection logic)
  1. Open in No.2 ATF temperature sensor circuit
  2. No.2 ATF temperature sensor
  3. ECM

MONITOR DESCRIPTION

These DTCs indicate an open or short in the No. 2 Automatic Transmission Fluid (ATF) temperature sensor circuit. The No. 2 ATF temperature sensor converts the ATF temperature to an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature, and detects any open or short malfunctions in the No. 2 ATF temperature sensor circuit. If the resistance (voltage) of the No. 2 ATF temperature sensor is less than 25 Ω (0.046 V) or more than 156 kΩ (4.915 V), the ECM interprets this as a fault in the No. 2 ATF temperature sensor or its wiring. The ECM turns on the MIL and stores a DTC.

WIRING DIAGRAM

C166894E03

INSPECTION PROCEDURE

HINT:
According to the Data List displayed on a intelligent tester, you can read the values of components, such as the switches, sensors, actuators, without removing any parts. Reading the Data List as a first step of troubleshooting is one method of shortening labor time.

NOTICE:
In the table below, the values listed under "Normal Condition" are for reference only. Do not depend solely on these reference values when judging whether a part is faulty or not.

  1. Warm up the engine.
  2. Turn the ignition switch to OFF.
  3. Connect the intelligent tester to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the tester ON.
  6. Enter the following menus: Powertrain / Engine and ECT / Data List.
  7. According to the display on the tester, read the Data List.
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A/T Oil Temperature 2
    No. 2 ATF Temperature Sensor Value/
    min.: -40°C (-40°F)
    max.: 215°C (419°F)
    1. After Stall Test:
      Approximately 80°C (176°F)
    2. Equal to ambient temperature during cold soak
    If the value is "-40°C (-40°F)" or "150°C (302°F) or more", No. 2 ATF temperature sensor circuit is open or short.

HINT:
When DTC P2742 is output and intelligent tester reading is 150°C (302°F) or more, there is a short circuit.
When DTC P2743 is output and intelligent tester reading is -40°C (-40°F), there is an open circuit.
Measure the resistance between terminal THO2 and the body ground.
Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
150°C (302°F) or more
Short circuit


1. INSPECT TRANSMISSION WIRE (NO.2 ATF TEMPERATURE SENSOR)

  1. C110342E84
    Disconnect the transmission wire connector from the transmission.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    1 (OT2-) - 9 (OT2+)
    79 Ω to 156 kΩ

  1. Measure the resistance.

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    1 (OT2-) - Body ground
    10 kΩ or higher
    9 (OT2+) - Body ground
    10 kΩ or higher

HINT:
If the resistance is outside the specified range at either of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.
ATF Temperature
Specified Condition
20°C (68°F)
3 to 5 kΩ
110°C (230°F)
0.22 to 0.28 kΩ



NG
REPAIR OR REPLACE TRANSMISSION WIRE (Click here)
OK


2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

  1. G038618E06
    Connect the transmission wire connector to the transmission.

  1. Disconnect the ECM connectors.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    B2-32 (THO2) - B1-28 (E2)
    79 Ω to 156 kΩ

  1. Measure the resistance.

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    B2-32 (THO2) - Body ground
    10 kΩ or higher
    B1-28 (E2) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P2716 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT) (from Aug 2009)P2742 Transmission Fluid Temperature Sensor "B" Circuit Low Input (+ P2743) (from Aug 2009) →