2011-2016 FJ Cruiser · Service Manual BRAKE

C1252/52 Brake Booster Pump Motor on Time Abnormally Long

Diagnostic trouble codes · Vehicles built Jul 2007 – Oct 2010

DESCRIPTION

The motor relay (semiconductor relay) is built into the master cylinder solenoid and drives the pump motor based on a signal from the skid control ECU.
DTC No.
DTC Detecting Condition
Trouble Areas
C1252/52
Motor operates for 3 minutes or more.
  1. Brake booster pump assembly
  2. Hydraulic brake booster (accumulator pressure sensor)
  3. Master cylinder solenoid (skid control ECU)

INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration (Click here).

HINT:
When C1253/53, C1254/54 or C1256/56 is output together with C1252/52, inspect and repair the trouble areas indicated by C1253/53, C1254/54 or C1256/56 first.


1. CHECK HYDRAULIC BRAKE BOOSTER PUMP MOTOR OPERATION
  1. Turn the ignition switch off.

  1. Depress the brake pedal more than 20 times.

  1. Turn the ignition switch to ON.

  1. Check how the hydraulic brake booster pump motor operates.

    Result:
    Result
    Proceed to
    Pump motor does not operate
    A
    Pump motor operates continuously (Does not stop)
    B
    Pump motor operates intermittently
    C
    Pump motor operates, then stops
    D



B
REPLACE BRAKE BOOSTER PUMP ASSEMBLY (Click here)

C
Go to step 4

D
Go to step 5
A


2. CHECK BRAKE PUMP MOTOR WIRE HARNESS CONNECTION (MT+ / MT-)
  1. Using a screwdriver, remove the 2 plugs from the hydraulic brake booster (Click here).

  1. Check the tightening torque of 2 screws which fasten the wire harness connecting the hydraulic brake booster and brake booster pump (Click here).

Torque:
2.9 N*m{ 30 kgf*cm , 26 in.*lbf }



NG
RETIGHTEN SCREWS
OK


3. CHECK RESISTANCE OF PUMP MOTOR WIRE HARNESS (MT+/MT-)

  1. F052356E02
    Using a screwdriver, remove the 2 screws and pull the wire harness from the hydraulic brake booster assembly.

  1. Measure the resistance between the red wire (MT+) and black wire (MT-).

    Standard resistance:
    Below 2 Ω



NG
REPLACE BRAKE BOOSTER PUMP ASSEMBLY (Click here)
OK


4. READ VALUE USING DATA LIST (ACCUMULATOR PRESSURE SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester to ON.

  1. Select the following menu items: Chassis / ABS/VSC/TRC/ Data List

    DATA LIST: ABS/VSC/TRC 
    Tester Display
    Measurement Item / Range
    Normal Condition
    Diagnostic Note
    Accumulator Sensor
    Accumulator pressure sensor reading / min.: 0 V, max.: 5 V
    3.58 to 5 V
    If value constant regardless of pump operation, accumulator pressure sensor malfunction suspected.

  1. Check that the accumulator pressure sensor output is normal.

    Result:
    Result
    Proceed to
    Output value varies within "Normal Condition" range
    A
    Output value does not reach "Normal Condition" range
    B
    Output value constant regardless of pump motor operation
    C



B
REPLACE BRAKE BOOSTER PUMP ASSEMBLY (Click here)

C
REPLACE HYDRAULIC BRAKE BOOSTER (Click here)
A


5. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON.

  1. Wait for more than 5 minutes.

  1. Check if the same DTC is recorded (Click here).

    Result:
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
REPLACE BRAKE BOOSTER PUMP ASSEMBLY (Click here)
A

REPLACE MASTER CYLINDER SOLENOID (Click here)


← C1252 Brake Booster Pump Motor on Time Abnormally Long (from Aug 2012)C1253 Pump Motor Relay (Nov 2010 – Jul 2012) →