2011-2016 FJ Cruiser · Service Manual COMMUNICATION SYSTEM

Open in One Side of CAN Branch Line

Circuit diagnosis · Vehicles built Aug 2009 – Oct 2010

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 from Aug 2012

DESCRIPTION

If 2 or more ECUs and/or sensors do not appear on the intelligent tester "CAN Bus Check" screen via the CAN VIM, one side of the CAN branch wire may be open. (one side of the CAN-H [branch wire] / CANL [branch wire] of the ECU and/or sensor is open.)
Symptom
Trouble Area
2 or more ECUs and/or sensors do not appear on intelligent tester "CAN Bus Check" screen via CAN VIM.
  1. Open in one side of CAN branch wire
  2. Master cylinder solenoid (skid control ECU)
  3. Yaw rate sensor
  4. Steering angle sensor

WIRING DIAGRAM

C134964E02

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system is not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
  1. Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
  2. The following is the troubleshooting procedure of an open in either CANH or CANL of the ECU A (SENSOR A).
  3. Perform the following inspection for the ECUs (sensors) which are not displayed on the intelligent tester. If malfunctions cannot be identified, then perform the following inspection for the ECUs (sensors) connected to CAN communication.


1. CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU)

  1. E192054E01
    Disconnect the A4 skid control ECU connector.

  1. Select "CAN Bus Check" on the intelligent tester (Click here).

    Result 
    Result
    Proceed to
    ABS/VSC/TRAC not displayed on the intelligent tester.
    A
    Several ECUs and sensors other than ABS/VSC/TRAC not displayed on intelligent tester.
    B
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Skid Control ECU)



B
Go to step 3
A


2. CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU BRANCH WIRE)

  1. E192054E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance.:
    Tester Connection
    Switch Condition
    Specified Condition
    A4-11 (CANH) - A4-25 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Skid Control ECU)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CAN-H, CAN-L)
OK

REPLACE MASTER CYLINDER SOLENOID

3. CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (YAW RATE SENSOR)

  1. E192055E01
    Disconnect the E34 yaw rate sensor connector.

  1. Select "CAN Bus Check" on the intelligent tester (Click here).

    Result 
    Result
    Proceed to
    Yaw Rate/Deceleration Sensor not displayed on the intelligent tester.
    A
    Several ECUs and sensors other than Yaw Rate/Deceleration Sensor not displayed on intelligent tester.
    B
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Yaw Rate Sensor)



B
Go to step 5
A


4. CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (YAW RATE SENSOR BRANCH WIRE)

  1. E192055E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance.:
    Tester Connection
    Switch Condition
    Specified Condition
    E34-3 (CANH) - E34-2 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Yaw Rate Sensor)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR (CAN-H, CAN-L)
OK

REPLACE YAW RATE SENSOR (Click here)

5. CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR BRANCH WIRE)

  1. E192056E02
    Disconnect the E16 steering angle sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance.:
    Tester Connection
    Switch Condition
    Specified Condition
    E16-3 (CANH) - E16-11 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Steering Angle Sensor)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CAN-H, CAN-L)
OK

REPLACE STEERING ANGLE SENSOR (Click here)


← Open in One Side of CAN Branch Line (Jul 2007 – Jul 2009)Open in One Side of CAN Branch Line (Nov 2010 – Jul 2011) →