2011-2016 FJ Cruiser · Service Manual COMMUNICATION SYSTEM

Open in One Side of CAN Branch Line

Circuit diagnosis · Vehicles built Aug 2011 – Jul 2012

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 from Aug 2012

DESCRIPTION

If 2 or more ECUs and/or sensors do not appear on the intelligent tester "CAN Bus Check" screen, one side of the CAN branch wire may be open (One side of the CANH [branch wire]/CANL [branch wire] of the ECU and/or sensor is open).
Symptom
Trouble Area
2 or more ECUs and/or sensors do not appear on the intelligent tester "CAN Bus Check" screen.
  1. One side of CAN branch wire is open
  2. Yaw rate sensor
  3. Master cylinder solenoid (skid control ECU)
  4. Airbag sensor assembly
  5. Steering angle sensor

WIRING DIAGRAM

E214872E02
E231209E01

INSPECTION PROCEDURE

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

NOTICE:
  1. Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.
  2. Turn the ignition switch off before inspecting CAN bus wires for a ground short.
  3. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not operating.
  4. Before measuring the resistance, first disconnect the cable from the negative battery terminal and confirm that the alarm function is no longer operating. Then, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.
  5. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

HINT:
  1. Perform the following inspection for the ECUs (sensors) which are not displayed on the intelligent tester. If a malfunction cannot be identified, perform the following inspections for the ECUs (sensors) connected to the CAN communication system.
  1. Do not remove the center airbag sensor assembly and ECM, as they are the end parts of the circuit. If removed, CAN communication will not be possible.
  1. The open circuit confirmation of the center airbag sensor assembly, ECM and main wire is performed in the Check CAN Bus Line procedure of How to Proceed with Troubleshooting. This inspection only has procedures for checking for an open circuit on one side of the CAN branch wire.


1. CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (YAW RATE SENSOR)
  1. Disconnect the E83 yaw rate sensor connector.

  1. Select "CAN Bus Check" on the intelligent tester (Click here).

    Result 
    Result
    Proceed to
    "Yaw Rate / Deceleration Sensor" not displayed on the intelligent tester.
    A
    Several ECUs and sensors other than "Yaw Rate / Deceleration Sensor" not displayed on the intelligent tester.
    B



B
Go to step 3
A


2. CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (YAW RATE SENSOR BRANCH WIRE)

  1. E175983E04
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E83-3 (CANH) - E83-2 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate Sensor)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE YAW RATE SENSOR (Click here)

3. CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (MASTER CYLINDER SOLENOID (SKID CONTROL ECU))
  1. Disconnect the A4 master cylinder solenoid (skid control ECU) connector.

  1. Select "CAN Bus Check" on the intelligent tester (Click here).

    Result 
    Result
    Proceed to
    "Skid Control (ABS/VSC/TRAC)" not displayed on the intelligent tester.
    A
    Several ECUs and sensors other than "Skid Control (ABS/VSC/TRAC)" not displayed on the intelligent tester.
    B



B
Go to step 5
A


4. CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (MASTER CYLINDER SOLENOID (SKID CONTROL ECU) BRANCH WIRE)

  1. B255884E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A4-11 (CANH) - A4-25 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Master Cylinder Solenoid (Skid Control ECU))



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU) (Click here)

5. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIRBAG SENSOR ASSEMBLY)
  1. Disconnect the E29 airbag sensor assembly connector.

  1. Select "CAN Bus Check" on the intelligent tester (Click here).

    Result 
    Result
    Proceed to
    "Airbag" not displayed on the intelligent tester.
    A
    Several ECUs and sensors other than "Airbag" not displayed on the intelligent tester.
    B



NG
Go to step 7
A


6. CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIRBAG SENSOR ASSEMBLY BRANCH WIRE)

  1. E186790E14
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E29-13 (CANH) - E29-22 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Airbag Sensor Assembly)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE AIR BAG SENSOR ASSEMBLY (Click here)

7. CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (STEERING ANGLE SENSOR BRANCH WIRE)

  1. E192049E04
    Disconnect the E16 steering angle sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E16-3 (CANH) - E16-11 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Steering Angle Sensor)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE STEERING ANGLE SENSOR (Click here)


← Open in One Side of CAN Branch Line (Nov 2010 – Jul 2011)Open in One Side of CAN Branch Line (from Aug 2012) →