2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

INSTALLATION

Removal / installation · Vehicles built Jul 2007 – Oct 2010

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012 from Aug 2012

HINT:
The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.


1. INSTALL REAR SPEAKER ASSEMBLY

  1. B135125
    Inert the 2 hooks into the 2 cutouts of the speaker mounting bracket and install the rear speaker with the 2 bolts.

    Torque:
    8.1 N*m{ 85 kgf*cm , 72 in.*lbf }

  1. Install the clamp.


2. INSTALL SPEAKER MOUNTING BRACKET

  1. B135126
    Install the speaker mounting bracket with the 2 bolts.

    Torque:
    8.1 N*m{ 85 kgf*cm , 72 in.*lbf }

  1. Connect the speaker connector.


3. INSTALL ROOF SIDE INNER GARNISH

  1. B130622
    Pass the rear seat outer belt through the slit in the roof side inner garnish.

  1. Engage the 7 clips and the claw and install the roof side inner garnish.

  1. Tighten the bolt.

    Torque:
    5.5 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the clip.

  1. B130621
    Engage the claw and close the cover.


4. INSTALL DECK TRIM SIDE PANEL ASSEMBLY
  1. for RH Side:

    1. Install the deck trim side panel assembly (Click here).

  1. for LH Side:

    1. Install the deck trim side panel assembly (Click here).


5. INSTALL REAR SEAT OUTER BELT ASSEMBLY

  1. B130782E01
    Check the angle of inclination required to lock the retractor.

    1. Gently incline the retractor from its initial position. Check that the belt does not lock when the retractor is inclined 15° or less in any direction. Also, check that the belt locks when the inclination of the retractor is 45° or more.

      NOTICE:
      Do not disassemble the retractor.

      If the operation is not as specified, replace the rear seat outer belt.

  1. B130780E01
    Hook the lower stay of the retractor onto the 2 body hooks and provisionally install the retractor with the 2 bolts.

  1. Tighten bolt A and then bolt B.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf } for bolt A
    42 N*m{ 428 kgf*cm , 31 ft.*lbf } for bolt B

  1. B130781
    Install the through anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Make sure that the shoulder anchor rotates smoothly.

  1. Check that the ELR locks.

    NOTICE:
    Perform the check with the front seat outer belt installed.


    1. With the belt installed, check that the belt locks when it is pulled out quickly.
      If the operation is not as specified, replace the rear seat outer belt.


6. INSTALL LAP BELT OUTER ANCHOR COVER

  1. B138385
    Engage the 3 claws and install the lap belt outer anchor cover.


7. INSTALL AMPLIFIER BOX SPEAKER ASSEMBLY (w/ Woofer)

  1. B134990
    Install the amplifier box speaker with the 4 screws.

    Torque:
    8.1 N*m{ 85 kgf*cm , 72 in.*lbf }

  1. Connect the speaker connector.


8. INSTALL SPEAKER MOUNTING COVER (w/ Woofer)

  1. B134991
    Engage the 8 clips and install the speaker mounting cover.


9. INSTALL DECK SIDE GARNISH (w/ Woofer)

  1. B134992
    Engage the 6 claws and install the deck side garnish.


10. INSTALL QUARTER TRIM POCKET (w/o Woofer)

  1. B130613
    Engage the 6 claws and install the quarter trim pocket.


11. INSTALL SIDE TRIM COVER (w/o Woofer)

  1. B130612
    Engage the 8 claws and install the side trim cover.


12. INSTALL QUARTER TRIM POCKET TRAY (w/o Woofer)

  1. B130611
    Engage the 7 claws and install the quarter trim pocket tray.


13. INSTALL PACKAGE HOLDER NET HOOK (w/o Woofer)

B130610E02

HINT:
Use the same procedure to install all the package holder net hooks.

  1. Install the package holder net hook with the bolt.

    Torque:
    8.1 N*m{ 83 kgf*cm , 72 in.*lbf }


14. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP

  1. B130604E01
    Align the locating marks with the paint marks first, and install the front door opening trim weatherstrip, as shown in the illustration.

    Paint mark:
    Area
    Color
    RH side
    White
    LH side
    Red


15. INSTALL ACCESS DOOR SCUFF PLATE

  1. B130598
    Engage the 6 claws and install the access door scuff plate.


16. INSTALL FRONT DOOR SCUFF PLATE

  1. B130597
    Engage the 14 claws and install the door scuff plate.


17. INSTALL REAR FLOOR MAT ASSEMBLY

  1. B130594
    Install the rear floor mat with the 2 clips.


18. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY

B179163E01

HINT:
Use the same procedure for both sides.

  1. Install the luggage hold belt striker with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Install the cap.


19. INSTALL REAR FLOOR MAT SUPPORT PLATE

  1. B130593
    Engage the 11 claws and install the rear floor mat support plate.

  1. B130592
    Tighten the 5 screws.


20. INSTALL REAR FLOOR BOARD

  1. B135075
    Engage the clip and claw and install the rear floor board.

  1. B135074E02
    Install the luggage hold belt striker with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    HINT:
    Use the same procedure for both sides.


21. INSTALL REAR SEATBACK ASSEMBLY
  1. for RH Side:

    1. Install the rear seatback assembly (Click here).

  1. for LH Side:

    1. Install the rear seatback assembly (Click here).


22. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY
  1. for RH Side:

    1. Install the rear seatback board carpet assembly (Click here).

  1. for LH Side:

    1. Install the rear seatback board carpet assembly (Click here).


23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }

← REMOVAL (from Aug 2012)INSTALLATION (Nov 2010 – Jul 2012) →