2011-2016 FJ Cruiser · Service Manual RESTRAINTS

B1628/82 Front Passenger Side - Side Airbag Sensor Assembly Initialization Incomplete

Diagnostic trouble codes · Vehicles built from Aug 2008

DESCRIPTION

The side airbag sensor RH and the rear airbag sensor RH consist of parts including the diagnostic circuit and the lateral deceleration sensor.
When the center airbag sensor assembly receives signals from the lateral deceleration sensor, it determines whether or not the SRS should be activated.
DTC B1628/82 is set when a malfunction is detected in the side airbag sensor RH or rear airbag sensor RH circuit.
DTC No.
Detection Condition
Trouble Area
B1628/82
  1. Center airbag sensor assembly detects open circuit signal in side airbag sensor RH circuit or rear airbag sensor RH circuit for 2 seconds.
  2. Side airbag sensor RH malfunction
  3. Rear airbag sensor RH malfunction
  4. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Side airbag sensor RH
  3. Rear airbag sensor RH
  4. Center airbag sensor assembly

WIRING DIAGRAM

C148422E22

INSPECTION PROCEDURE

NOTICE:
In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.

  1. Turn the ignition switch off.
  2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. Disconnect the connector from the center airbag sensor assembly.
  4. Disconnect the connectors from the steering pad.
  5. Disconnect the connectors from the front passenger airbag assembly.
  6. Disconnect the connector from the front seat outer belt assembly LH.
  7. Disconnect the connector from the front seat outer belt assembly RH.
  8. Disconnect the connector from the front seat side airbag assembly LH.
  9. Disconnect the connector from the front seat side airbag assembly RH.
  10. Disconnect the connector from the curtain shield airbag assembly LH.
  11. Disconnect the connector from the curtain shield airbag assembly RH.

1. CHECK DTC OUTPUT
  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check the DTCs (Click here ).

    Result:
    Result
    Proceed to
    DTCs B1622/81 and B1627/82 are not output.
    A
    DTCs (PAST DTCs) B1622/81 and B1627/82 are output
    and
    DTC (PRESENT DTC) B1628/82 is output.
    B
    DTCs (PAST DTCs) B1622/81 and B1627/82 are output
    and
    DTC (PRESENT DTC) B1623/81 is output.
    C

    HINT:
    1. DTCs other than DTC B1622/81, B1623/81, B1627/82 and B1628/82 may be output at this time, but they are not related to this check.



B
GO TO ANOTHER TROUBLESHOOTING (Click here)

C
GO TO ANOTHER TROUBLESHOOTING (Click here)
A


2. CHECK CONNECTORS (CENTER AIRBAG SENSOR ASSEMBLY - SIDE AIRBAG SENSOR RH)
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the floor wire connectors from the center airbag sensor assembly and the side airbag sensor RH.

  1. Check the floor wire connectors and terminals (on the center airbag sensor assembly and the side airbag sensor RH sides) and check that the connectors are properly connected.

    Result:
    Result
    Proceed to
    No problem.
    A
    Connectors or terminals incorrect.
    B
    Connectors connected improperly.
    C



B
REPLACE FLOOR WIRE

C
CONNECT CONNECTORS PROPERLY
A


3. CHECK FLOOR WIRE (CENTER AIRBAG SENSOR ASSEMBLY - SIDE AIRBAG SENSOR RH)
C192778E02
  1. Check for short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      K10-17 (BBP+) - Body ground
      Ignition switch ON
      Below 1 V
      K10-18 (BBP-) - Body ground
      Ignition switch ON
      Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check for open in the circuit.

    1. Using a service wire, connect K2-4 (BBR+) and K2-3 (BBR-) of connector C.

      NOTICE:
      Do not forcibly insert the service wire into the terminals of the connector when connecting.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      K10-17 (BBP+) - K10-18 (BBP-)
      Always
      Below 1 Ω

  1. Check for short in the circuit.

    1. Disconnect the service wire from connector C.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      K10-17 (BBP+) - K10-18 (BBP-)
      Always
      1 MΩ or higher

  1. Check for short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      K10-17 (BBP+) - Body ground
      Always
      1 MΩ or higher
      K10-18 (BBP-) - Body ground
      Always
      1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK


4. CHECK CONNECTORS (SIDE AIRBAG SENSOR RH - REAR AIRBAG SENSOR RH)
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the floor wire connectors from the side airbag sensor RH and the rear airbag sensor RH.

  1. Check the floor wire connectors and terminals (on the side airbag sensor RH and the rear airbag sensor RH sides) and check that the connectors are properly connected.

    Result:
    Result
    proceed to
    No problem.
    A
    Connectors or terminals incorrect.
    B
    Connectors connected improperly.
    C



B
REPLACE FLOOR WIRE

C
CONNECT CONNECTORS PROPERLY
A


5. CHECK FLOOR WIRE (SIDE AIRBAG SENSOR RH - REAR AIRBAG SENSOR RH)
C192777E02
  1. Check for short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      K2-1 (BCR+) - Body ground
      Ignition switch ON
      Below 1 V
      K2-2 (BCR-) - Body ground
      Ignition switch ON
      Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check for open in the circuit.

    1. Using a service wire, connect K3-1 (BCR-) and K3-2 (BCR+) of connector C.

      NOTICE:
      Do not forcibly insert the service wire into the terminals of the connector when connecting.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      K2-1 (BCR+) - K2-2 (BCR-)
      Always
      Below 1 Ω

  1. Check for short in the circuit.

    1. Disconnect the service wire from connector C.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      K2-1 (BCR+) - K2-2 (BCR-)
      Always
      1 MΩ or higher

  1. Check for short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      K2-1 (BCR+) - Body ground
      Always
      1 MΩ or higher
      K2-2 (BCR-) - Body ground
      Always
      1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK


6. CHECK SIDE AIRBAG SENSOR RH
  1. Connect the connector to the center airbag sensor assembly.

  1. C146230E18
    Interchange the side airbag sensor RH with the side airbag sensor LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here ).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here ).

    Result:
    Result
    Proceed to
    DTC B1628/82 is output.
    A
    DTC B1623/81 is output.
    B
    DTC B1623/81 or B1628/82 is not output.
    C

    HINT:
    DTCs other than DTC B1623/81 and B1628/82 may be output at this time, but they are not related to this check.



B
REPLACE SIDE AIRBAG SENSOR RH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


7. CHECK REAR AIRBAG SENSOR RH
  1. Connect the connector to the side airbag sensor RH.

  1. C148441E01
    Interchange the rear airbag sensor RH with the rear airbag sensor LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here ).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here ).

    Result:
    Result
    Proceed to
    DTC B1623/81 or B1628/82 is not output.
    A
    DTC B1628/82 is output.
    B
    DTC B1623/81 is output.
    C

    HINT:
    DTCs other than DTC B1623/81 and B1628/82 may be output at this time, but they are not related to this check.



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE REAR AIRBAG SENSOR RH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)


← B1625/22 Front Passenger Side - Side Airbag Sensor Malfunction (+ B1627/82) (from Aug 2008)B1630/23 Driver Side Rear Airbag Sensor Malfunction (from Aug 2008) →