2011-2016 FJ Cruiser · Service Manual RESTRAINTS

B1608/84 Front Satellite Sensor Bus LH Initialization Incomplete

Diagnostic trouble codes · Vehicles built from Aug 2008

Also covers:

DESCRIPTION

The front airbag sensor LH consists of parts including the diagnostic circuit and the frontal deceleration sensor.
When the center airbag sensor assembly receives signals from the frontal deceleration sensor, it determines whether or not the SRS should be activated.
DTC B1608/84, B1617/84 or B1618/84 is set when a malfunction is detected in the front airbag sensor LH circuit.
DTC No.
Detection Condition
Trouble Area
B1608/84
B1617/84
B1618/84
  1. Center airbag sensor assembly detects line short circuit signal, open circuit signal, short circuit to ground signal or short to B+ signal in front airbag sensor LH circuit for 2 seconds.
  2. Front airbag sensor LH malfunction
  3. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Engine room main wire
  3. Front airbag sensor LH
  4. Center airbag sensor assembly

WIRING DIAGRAM

H102626E02

INSPECTION PROCEDURE

NOTICE:
In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.

  1. Turn the ignition switch off.
  2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. Disconnect the connector from the center airbag sensor assembly.
  4. Disconnect the connectors from the steering pad.
  5. Disconnect the connectors from the front passenger airbag assembly.
  6. Disconnect the connector from the front seat outer belt assembly LH.
  7. Disconnect the connector from the front seat outer belt assembly RH.
  8. Disconnect the connector from the front seat side airbag assembly LH.
  9. Disconnect the connector from the front seat side airbag assembly RH.
  10. Disconnect the connector from the curtain shield airbag assembly LH.
  11. Disconnect the connector from the curtain shield airbag assembly RH.

1. CHECK CONNECTOR (INSTRUMENT PANEL WIRE - CENTER AIRBAG SENSOR ASSEMBLY)
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the instrument panel wire connector from the center airbag sensor assembly.

  1. Check the instrument panel wire connector and terminals (on the center airbag sensor assembly side) and check that the connector is properly connected to the center airbag sensor assembly.

    Result:
    Result
    Proceed to
    No problem.
    A
    Connector or terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPLACE INSTRUMENT PANEL WIRE

C
CONNECT CONNECTOR PROPERLY
A


2. CHECK CONNECTOR (ENGINE ROOM MAIN WIRE - FRONT AIRBAG SENSOR LH)
  1. Disconnect the engine room main wire connector from the front airbag sensor LH.

  1. Check the engine room main wire connector and terminals (on the front airbag sensor LH side) and check that the connector is properly connected to the front airbag sensor LH.

    Result:
    Result
    Proceed to
    No problem.
    A
    Connector or terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPLACE ENGINE ROOM MAIN WIRE

C
CONNECT CONNECTOR PROPERLY
A


3. CHECK FRONT AIRBAG SENSOR LH CIRCUIT
C192774E02
  1. Check for short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      E29-30 (+SL) - Body ground
      Ignition switch ON
      Below 1 V
      E29-28 (-SL) - Body ground
      Ignition switch ON
      Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check for open in the circuit.

    1. Using a service wire, connect A15-1 and A15-2 of connector E.

      NOTICE:
      Do not forcibly insert the service wire into the terminals of the connector when connecting.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E29-30 (+SL) - E29-28 (-SL)
      Always
      Below 1 Ω

  1. Check for short in the circuit.

    1. Disconnect the service wire from connector E.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E29-30 (+SL) - E29-28 (-SL)
      Always
      1 MΩ or higher

  1. Check for short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E29-30 (+SL) - Body ground
      Always
      1 MΩ or higher
      E29-28 (-SL) - Body ground
      Always
      1 MΩ or higher



NG
Go to step 5
OK


4. CHECK FRONT AIRBAG SENSOR LH
C148689E17
  1. Connect the connectors to the center airbag sensor assembly.

  1. Interchange the front airbag sensor LH with the front airbag sensor RH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here ).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here ).

    Result:
    Result
    Proceed to
    DTC B1608/84, B1617/84 or B1618/84 is output.
    A
    DTC B1603/83, B1612/83 or B1613/83 is output.
    B



B
REPLACE FRONT AIRBAG SENSOR LH (Click here)
A

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

5. CHECK CONNECTOR (ENGINE ROOM MAIN WIRE - INSTRUMENT PANEL WIRE)
  1. Disconnect the engine room main wire connector from the instrument panel wire.

  1. Check the engine room main wire connector and terminals (on the instrument panel wire side) and check that the connector is properly connected to the instrument panel wire.

    Result:
    Result
    Proceed to
    No problem.
    A
    Connector or terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPLACE ENGINE ROOM MAIN WIRE

C
CONNECT CONNECTOR PROPERLY
A


6. CHECK ENGINE ROOM MAIN WIRE
C192775E02
  1. Check for short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      EA3-1 - Body ground
      Ignition switch ON
      Below 1 V
      EA3-2 - Body ground
      Ignition switch ON
      Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check for open in the circuit.

    1. Using a service wire, connect A15-1 and A15-2 of connector E.

      NOTICE:
      Do not forcibly insert the service wire into the terminals of the connector when connecting.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      EA3-1 - EA3-2
      Always
      Below 1 Ω

  1. Check for short in the circuit.

    1. Disconnect the service wire from connector E.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      EA3-1 - EA3-2
      Always
      1 MΩ or higher

  1. Check for short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      EA3-1 - Body ground
      Always
      1 MΩ or higher
      EA3-2 - Body ground
      Always
      1 MΩ or higher



NG
REPLACE ENGINE ROOM MAIN WIRE
OK

REPLACE INSTRUMENT PANEL WIRE


← B1603/83 Front Satellite Sensor Bus RH Initialization Incomplete (+ B1612/83, B1613/83) (from Aug 2008)B1610/13 Front Airbag Sensor RH Malfunction (from Aug 2008) →