B1637/82 Lost Communication with Rear Airbag Sensor LH
Diagnostic trouble codes · Vehicles built from Aug 2012
DESCRIPTION
The side collision sensor LH circuit (to determine deployment of the front seat airbag assembly LH and curtain shield airbag assembly LH) is composed of the center airbag sensor assembly, side airbag sensor assembly LH and rear airbag sensor LH.The side airbag sensor assembly LH and rear airbag sensor LH detect impacts to the vehicle and send signals to the center airbag sensor assembly to determine if the airbag should be deployed.
DTC B1637/82 is stored when a malfunction is detected in the side collision sensor LH circuit.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B1637/82 |
|
|
WIRING DIAGRAM
Refer to DTC B1628/82 (Click here).INSPECTION PROCEDURE
- NOTICE:
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
| 1. CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check that the connectors are properly connected to the side airbag sensor assembly LH and rear airbag sensor LH.
- OK:
- The connectors are properly connected.
- HINT:
- If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the side airbag sensor assembly LH and rear airbag sensor LH.
Check that the terminals of the connectors are not damaged.
- OK:
- The terminals are not deformed or damaged.
|
|
||||
| OK | |
| 2. CHECK NO. 2 FLOOR WIRE (OPEN) |
Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

- NOTICE:
- Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
L4-1 (BCL+) - L4-2 (BCL-)
Always
Below 1 Ω
Disconnect the service wire from connector C.
Text in Illustration *1
Rear Airbag Sensor LH
*2
Side Airbag Sensor Assembly LH
*3
No. 2 Floor Wire
*4
Service Wire
*a
Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)
*b
Front view of wire harness connector
(to Rear Airbag Sensor LH)
|
|
||||
| OK | |
| 3. CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
L4-1 (BCL+) - Body ground
Always
1 MΩ or higher
L4-2 (BCL-) - Body ground
Always
1 MΩ or higher
Text in Illustration *1
Rear Airbag Sensor LH
*2
Side Airbag Sensor Assembly LH
*3
No. 2 Floor Wire
*a
Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)
|
|
||||
| OK | |
| 4. CHECK NO. 2 FLOOR WIRE (SHORT) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
L4-1 (BCL+) - L4-2 (BCL-)
Always
1 MΩ or higher
Text in Illustration *1
Rear Airbag Sensor LH
*2
Side Airbag Sensor Assembly LH
*3
No. 2 Floor Wire
*a
Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)
|
|
||||
| OK | |
| 5. CHECK NO. 2 FLOOR WIRE (SHORT TO B+) |
Connect the cable to the negative (-) battery terminal.

Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
L4-1 (BCL+) - Body ground
Ignition switch ON
Below 1 V
L4-2 (BCL-) - Body ground
Ignition switch ON
Below 1 V
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Text in Illustration *1
Rear Airbag Sensor LH
*2
Side Airbag Sensor Assembly LH
*3
No. 2 Floor Wire
*a
Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)
|
|
||||
| OK | |
| 6. CHECK SIDE AIRBAG SENSOR ASSEMBLY LH |
Connect the connector to the rear airbag sensor LH.

Interchange the side airbag sensor assembly LH with RH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
- Result:
Result
Proceed to
DTC B1637/82 is output.
A
DTC B1632/81 is output.
B
DTCs B1632/81 and B1637/82 are not output.
C
- HINT:
- Codes other than DTCs B1632/81 and B1637/82 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.
Text in Illustration *1
Side Airbag Sensor Assembly RH
*2
Center Airbag Sensor Assembly
|
|
||||
|
|
||||
| A | |
| 7. CHECK REAR AIRBAG SENSOR LH |
Interchange the rear airbag sensor LH with RH and connect the connectors.

Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
- Result:
Result
Proceed to
DTCs B1632/81 and B1637/82 are not output.
A
DTC B1637/82 is output.
B
DTC B1632/81 is output.
C
- HINT:
- Codes other than DTCs B1632/81 and B1637/82 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the rear airbag sensor LH and RH to their original positions and connect the connectors.
Text in Illustration *1
Rear Airbag Sensor RH
*2
Side Airbag Sensor Assembly LH
|
|
||||
|
|
||||
| A | ||
| ||
