2011-2016 FJ Cruiser · Service Manual RESTRAINTS

B1647/82 Lost Communication with Side Satellite Sensor Bus LH

Diagnostic trouble codes · Vehicles built from Aug 2012

DESCRIPTION

The side collision sensor LH circuit (to determine deployment of the front seat airbag assembly LH and curtain shield airbag assembly LH) is composed of the center airbag sensor assembly, side airbag sensor assembly LH and rear airbag sensor LH.
The side airbag sensor assembly LH and rear airbag sensor LH detect impacts to the vehicle and send signals to the center airbag sensor assembly to determine if the airbag should be deployed.
DTC B1647/82 is stored when a malfunction is detected in the side collision sensor LH circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1647/82
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side collision sensor LH circuit.
  2. Side airbag sensor assembly LH malfunction
  3. Rear airbag sensor LH malfunction
  4. Center airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. Side airbag sensor assembly LH
  3. Rear airbag sensor LH
  4. Center airbag sensor assembly

WIRING DIAGRAM

Refer to DTC B1628/82 (Click here).

INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).


1. CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the center airbag sensor assembly, side airbag sensor assembly LH and rear airbag sensor LH.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the center airbag sensor assembly, side airbag sensor assembly LH and rear airbag sensor LH.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE NO. 2 FLOOR WIRE
OK


2. CHECK NO. 2 FLOOR WIRE (OPEN)

  1. C268574E03
    Using a service wire, connect terminals 8 (BBL+) and 15 (BBL-) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L4-4 (BBL+) - L4-3 (BBL-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Center Airbag Sensor Assembly
    *3
    No. 2 Floor Wire
    *4
    Service Wire
    *a
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *b
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly LH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


3. CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)

  1. C268575E03
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L4-4 (BBL+) - Body ground
    Always
    1 MΩ or higher
    L4-3 (BBL-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Center Airbag Sensor Assembly
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly LH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


4. CHECK NO. 2 FLOOR WIRE (SHORT)

  1. C268575E03
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L4-4 (BBL+) - L4-3 (BBL-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Center Airbag Sensor Assembly
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly LH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


5. CHECK NO. 2 FLOOR WIRE (SHORT TO B+)

  1. C268575E03
    Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    L4-4 (BBL+) - Body ground
    Ignition switch ON
    Below 1 V
    L4-3 (BBL-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Center Airbag Sensor Assembly
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly LH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


6. CHECK NO. 2 FLOOR WIRE (OPEN)

  1. C268577E07
    Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L4-1 (BCL+) - L4-2 (BCL-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector C.

    Text in Illustration 
    *1
    Rear Airbag Sensor LH
    *2
    Side Airbag Sensor Assembly LH
    *3
    No. 2 Floor Wire
    *4
    Service Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly LH)
    *b
    Front view of wire harness connector
    (to Rear Airbag Sensor LH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


7. CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)

  1. C268578E06
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L4-1 (BCL+) - Body ground
    Always
    1 MΩ or higher
    L4-2 (BCL-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Rear Airbag Sensor LH
    *2
    Side Airbag Sensor Assembly LH
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly LH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


8. CHECK NO. 2 FLOOR WIRE (SHORT)

  1. C268578E06
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L4-1 (BCL+) - L4-2 (BCL-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Rear Airbag Sensor LH
    *2
    Side Airbag Sensor Assembly LH
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly LH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


9. CHECK NO. 2 FLOOR WIRE (SHORT TO B+)

  1. C268578E06
    Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    L4-1 (BCL+) - Body ground
    Ignition switch ON
    Below 1 V
    L4-2 (BCL-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Rear Airbag Sensor LH
    *2
    Side Airbag Sensor Assembly LH
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly LH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


10. CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

  1. C267560E01
    Connect the connectors to the rear airbag sensor LH and center airbag sensor assembly.

  1. Interchange the side airbag sensor assembly LH with RH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1647/82 is output.
    A
    DTC B1642/81 is output.
    B
    DTCs B1642/81 and B1647/82 are not output.
    C

    HINT:
    Codes other than DTCs B1642/81 and B1647/82 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Center Airbag Sensor Assembly



B
REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


11. CHECK REAR AIRBAG SENSOR LH

  1. C268576E01
    Interchange the rear airbag sensor LH with RH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTCs B1642/81 and B1647/82 are not output.
    A
    DTC B1647/82 is output.
    B
    DTC B1642/81 is output.
    C

    HINT:
    Codes other than DTCs B1642/81 and B1647/82 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the rear airbag sensor LH and RH to their original positions and connect the connectors.

    Text in Illustration 
    *1
    Rear Airbag Sensor RH
    *2
    Side Airbag Sensor Assembly LH



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE REAR AIRBAG SENSOR LH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)


← B1643/81 Driver Side Satellite Sensor Bus Initialization Incomplete (Nov 2010 – Jul 2012)B1647/82 Lost Communication with Front Passenger Side Satellite Sensor Bus (Jul 2007 – Oct 2010) →