2011-2016 FJ Cruiser · Service Manual ENGINE

P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)

Diagnostic trouble codes · Vehicles built Jul 2007 – Nov 2007

Also covers:

Versions by build date: Jul 2007 – Nov 2007 Dec 2007 – Jul 2009 Aug 2009 – Jul 2014 from Aug 2014

DESCRIPTION

HINT:
  1. Although the DTC titles say oxygen sensor, these DTCs relate to the Air Fuel Ratio (A/F) sensor.
  2. Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.

The A/F sensor, which is located between the exhaust manifold and catalyst, consists of alloyed metal elements and a heater.
Depending on the engine operating conditions, the heater heats the sensor elements to activate them. Battery voltage is applied to the heater, the sensor ground is controlled by the ECM using a duty ratio.
The sensor elements convert the oxygen concentration in the exhaust gas into voltage values to output. Based on the voltage, the ECM determines the air fuel ratio and regulates the fuel injection volume depending on the air fuel ratio and engine operating conditions. The voltage changes between 0.6 V and 4.5 V while the engine is running. If the air fuel ratio is lean, which means the oxygen concentration in the exhaust gas is high, the voltage is high. If the air fuel ratio is rich, which means the oxygen concentration in the exhaust gas is low, the voltage is low.
A133442E01
A171616E01
DTC No.
DTC Detection Condition
Trouble Area
P2237
P2240
Open in the circuit between terminals A1A+/A2A+ and A1A-/A2A- of the Air Fuel Ratio (A/F) sensor while engine is running
(2 trip detection logic)
  1. Open in Air Fuel Ratio (A/F) sensor (bank 1 and 2, sensor 1) circuit
  2. A/F sensor (bank 1 and 2, sensor 1)
  3. ECM
P2238
P2241
Any of the following conditions are met
(2 trip detection logic)
  1. Air Fuel Ratio (A/F) sensor output drops while engine is running.
  1. Voltage at terminal A1A+/A2A+ is 0.5 V or less.
  1. Voltage difference between terminals A1A+/A2A+ and A1A-/A2A- is 0.1 V or less.
  1. Open or short in Air Fuel Ratio (A/F) sensor (bank 1 and 2, sensor 1) circuit
  2. A/F sensor (bank 1 and 2, sensor 1)
  3. ECM
P2239
P2242
A1A+/A2A+ voltage more than 4.5 V
(2 trip detection logic)
  1. Open or short in Air Fuel Ratio (A/F) sensor (bank 1 and 2, sensor 1) circuit
  2. A/F sensor (bank 1 and 2, sensor 1)
  3. ECM
P2252
P2255
A1A-/A2A- voltage 0.5 V or less
(2 trip detection logic)
  1. Open or short in Air Fuel Ratio (A/F) sensor (bank 1 and 2, sensor 1) circuit
  2. A/F sensor (bank 1 and 2, sensor 1)
  3. ECM
P2253
P2256
A1A-/A2A- voltage more than 4.5 V
(2 trip detection logic)
  1. Open or short in Air Fuel Ratio (A/F) sensor (bank 1 and 2, sensor 1) circuit
  2. A/F sensor (bank 1 and 2, sensor 1)
  3. ECM

MONITOR DESCRIPTION

These DTCs are output when there is an open or short in the Air Fuel Ratio (A/F) sensor circuit, or if the A/F sensor output drops. To detect these problems, the voltage of the A/F sensor is monitored when turning the ignition switch to the ON position, and the admittance (admittance is an electrical term that indicates the ease of flow of current) is checked while driving. If the voltage of the A/F sensor is between 0.6 V and 4.5 V, it is considered normal. If the voltage is out of the specified range, or the admittance is less than the standard value, the ECM will determine that there is a malfunction in the A/F sensor. If the same malfunction is detected in next driving cycle, the MIL will be illuminated and a DTC will be stored.

WIRING DIAGRAM

A172866E01

CONFIRMATION DRIVING PATTERN

HINT:
  1. This confirmation driving pattern is used in the "PERFORM CONFIRMATION DRIVING PATTERN" procedure of the following diagnostic troubleshooting procedure.
  2. Performing this confirmation pattern will activate the heated oxygen sensor monitor. This is useful for verifying the completion of the repair.

A172863E01
  1. Connect an intelligent tester to the DLC3.
  2. Turn the ignition switch ON.
  3. Turn the tester ON.
  4. Clear DTCs (Click here).
  5. Switch the ECM from normal mode to check mode (Click here).
  6. Select the following menu items: Powertrain / Engine and ECT / Data List / O2S (A/FS) Monitor.
  7. Check that the item O2S (A/FS) Monitor displays Incmpl (Incomplete).
  8. Start the engine and warm it up. (Proceed to "A")
  9. Drive the vehicle at between 60 km/h and 120 km/h (37 mph and 75 mph) for at least 10 minutes. (Proceed to "B")
  10. Note the state of the Data List items. Those items will change to Compl (Complete) as the O2 Sensor monitor operates.
  11. On the tester, select the following menu items: Powertrain / Engine and ECT / DTC and check if any DTCs (any pending DTCs) are set.

HINT:
If the item O2S (A/FS) Monitor does not change to Compl (Complete), and any pending DTCs fail to set, extend the driving time.


INSPECTION PROCEDURE

HINT:
Intelligent tester only:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F sensor function provided in the Active Test. The Control the Injection Volume for A/F sensor function can help to determine whether the Air Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume for A/F sensor operation using the intelligent tester.
  1. Connect the intelligent tester to the DLC3.
  2. Start the engine and turn the tester ON.
  3. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  4. On the tester, select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.
  5. Perform the Active Test operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume.)
  6. Monitor the output voltages of the A/F and HO2 sensors (AFS B1 S1 and O2S B1 S2) displayed on the tester.

HINT:
  1. The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
  2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

Tester Display (Sensor)
Injection Volume
Status
Voltage
AFS B1 S1
(A/F)
+25%
Rich
Less than 3.0 V
AFS B1 S1
(A/F)
-12.5%
Lean
More than 3.35 V
O2S B1 S2
(HO2)
+25%
Rich
More than 0.55 V
O2S B1 S2
(HO2)
-12.5%
Lean
Less than 0.4 V

NOTICE:
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

Case
A/F Sensor (Sensor 1) Output Voltage
HO2 Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E01
A151324E01
A150787E01
A150788E01
-
2
A150787E01
A150790E01
A150787E01
A150788E01
  1. A/F sensor
  2. A/F sensor heater
  3. A/F sensor circuit
3
A150787E01
A151324E01
A150787E01
A150790E01
  1. HO2 sensor
  2. HO2 sensor heater
  3. HO2 sensor circuit
4
A150787E01
A150790E01
A150787E01
A150790E01
  1. Fuel injector
  2. Fuel pressure
  3. Gas leak from exhaust system (Air fuel ratio extremely rich or lean)
  1. Following the Control the Injection Volume for A/F sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
  2. To display the graph, select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / A/F Control System / AFS B1 S1 and O2S B1 S2, and then press View button.

HINT:
  1. Read freeze frame data using an intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)
A171633E02
  1. Disconnect the B31 or B33 A/F sensor connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage between the +B terminal of the A/F sensor connector and body ground.

    Standard Voltage:
    Tester Connections
    Specified Conditions
    +B (B33-2) - Body ground
    11 to 14 V
    +B (B31-2) - Body ground

  1. Turn the ignition switch OFF.

  1. Disconnect the B2 ECM connector.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    HA1A (B33-1) - HA1A (B2-2)
    Below 1 Ω
    A1A+ (B33-3) - A1A+ (B2-22)
    A1A- (B33-4) - A1A- (B2-30)
    HA2A (B31-1) - HA2A (B2-1)
    A2A+ (B31-3) - A2A+ (B2-23)
    A2A- (B31-4) - A2A- (B2-31)

    Standard Resistance (Check for short):
    Tester Connections
    Specified Conditions
    HA1A (B33-1) or HA1A (B2-2) - Body ground
    10 kΩ or higher
    A1A+ (B33-3) or A1A+ (B2-22) - Body ground
    A1A- (B33-4) or A1A- (B2-30) - Body ground
    HA2A (B31-1) or HA2A (B2-1) - Body ground
    A2A+ (B31-3) or A2A+ (B2-23) - Body ground
    A2A- (B31-4) or A2A- (B2-31) - Body ground

  1. Reconnect the ECM connector.

  1. Reconnect the A/F sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


3. PERFORM CONFIRMATION DRIVING PATTERN

NEXT


4. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect a Techstream to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC / Pending.

  1. Read pending DTCs.

    Result:
    Result
    Proceed To
    No output
    A
    P2237, P2238, P2239, P2240, P2241, P2242. P2252, P2253, P2255 or P2256
    B



B
REPLACE ECM (Click here)
A

END


← P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1) (+ P2196, P2197, P2198) (from Nov 2010)P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1) (+ 9 more codes) (Dec 2007 – Jul 2009) →