Remove the 12 bolts, seal washer, cylinder head cover and gasket.
HINT:
Make sure the removed parts are returned to the same places they were removed from.
Remove the 3 gaskets.
18.
REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
Remove the 12 bolts, seal washer, cylinder head cover and gasket.
HINT:
Make sure the removed parts are returned to the same places they were removed from.
Remove the 3 gaskets.
19.
REMOVE SPARK PLUG TUBE GASKET
Bend the ventilation baffle plate claws on the cylinder head cover to an angle of 90° or more.
Text in Illustration
*a
Pry
Remove the 6 spark plug tube gaskets.
NOTICE:
Be careful not to damage the gasket when removing it, as the removed gasket needs to be used when installing a new one.
20.
REMOVE OIL PAN DRAIN PLUG
Remove the drain plug and gasket.
21.
REMOVE NO. 2 OIL PAN SUB-ASSEMBLY
Remove the 10 bolts and 2 nuts.
HINT:
Make sure the removed parts are returned to the same places they were removed from.
Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.
Text in Illustration
*1
Oil Pan Seal Cutter
NOTICE:
Be careful not to damage the contact surfaces of the oil pans.
22.
REMOVE OIL STRAINER SUB-ASSEMBLY
Remove the 2 nuts, oil strainer and gasket.
23.
REMOVE OIL PAN SUB-ASSEMBLY
Remove the 17 bolts and 2 nuts.
HINT:
Make sure the removed parts are returned to the same places they were removed from.
Using a screwdriver, remove the oil pan by prying between the oil pan and cylinder block as shown in the illustration.
Text in Illustration
*a
LH Side:
*b
RH Side:
*c
Pry
NOTICE:
Be careful not to damage the contact surfaces of the cylinder block or oil pan.
HINT:
Tape the screwdriver tip before use.
Remove the 3 O-rings from the timing chain cover.
24.
REMOVE NO. 1 OIL PAN BAFFLE PLATE
Remove the 6 bolts and No. 1 oil pan baffle plate.
25.
REMOVE ENGINE REAR OIL SEAL RETAINER
Remove the 5 bolts and 2 nuts.
Using a screwdriver, remove the oil seal retainer by prying between the oil seal retainer and crankshaft bearing cap.
Text in Illustration
*a
Pry
HINT:
Tape the screwdriver tip before use.
26.
REMOVE REAR CRANKSHAFT OIL SEAL
Using a screwdriver and hammer, tap out the oil seal.
NOTICE:
Be careful not to damage the rear oil seal retainer.
27.
REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
Remove the 26 bolts and the 2 nuts.
Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.
HINT:
Tape the screwdriver tip before use.
NOTICE:
Be careful not to damage the contact surfaces of the timing chain cover, cylinder block or cylinder head.
Remove the oil pump gasket from the cylinder block.
28.
REMOVE WATER PUMP ASSEMBLY
Remove the 8 bolts, water pump and gasket.
29.
REMOVE FRONT CRANKSHAFT OIL SEAL
Using a screwdriver and wooden block, pry out the oil seal.
HINT:
Tape the screwdriver tip before use.
NOTICE:
Do not damage the surface of the oil seal press fit hole.
30.
SET NO. 1 CYLINDER TO TDC / COMPRESSION
Temporarily tighten the pulley set bolt.
Turn the crankshaft clockwise to align the timing mark on the crank angle sensor plate with the RH block bore center line (TDC/compression).
Text in Illustration
*1
Center Line
*2
Timing Mark
*3
Sensor Plate
Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration. If not, turn the crankshaft clockwise 1 revolution (360°) and align the timing marks as above.
Text in Illustration
*1
Timing Mark
31.
REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.
Text in Illustration
*1
Plunger
*2
Stopper Plate
*3
Pin
Move the stopper plate downward to set the lock, and insert a pin of φ1.27 mm (0.0500 in.) into the stopper plate hole.
Remove the 2 bolts and No. 1 chain tensioner assembly.
32.
REMOVE CHAIN TENSIONER SLIPPER
Remove the chain tensioner slipper.
33.
REMOVE CHAIN SUB-ASSEMBLY
Turn the crankshaft counterclockwise 10° to loosen the chain of the crankshaft timing sprocket.
Text in Illustration
*1
Center Line
*2
Timing Mark
*3
Sensor Plate
Remove the pulley set bolt.
Remove the chain sub-assembly from the crankshaft timing sprocket and place it on the crankshaft.
Turn the camshaft timing gear assembly on bank 1 clockwise approximately 60° so that it is as shown in the illustration. Be sure to loosen the chain subassembly between the banks.
Remove the chain sub-assembly.
Text in Illustration
*a
Bank 1:
34.
REMOVE NO. 1 IDLE GEAR SHAFT
Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, No. 1 idle gear and No. 1 idle gear shaft.
35.
REMOVE NO. 1 CHAIN VIBRATION DAMPER
Remove the 2 bolts and No. 1 chain vibration damper.
36.
REMOVE NO. 2 CHAIN VIBRATION DAMPER
Remove the 2 No. 2 chain vibration dampers.
37.
REMOVE CRANKSHAFT TIMING SPROCKET
Remove the crankshaft timing sprocket.
38.
REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)
While raising the No. 2 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to hold the No. 2 chain tensioner assembly.
Text in Illustration
*1
Pin
*2
Plunger
*a
Push
Using SST to hold the hexagonal portion of each camshaft, loosen the bolts of the camshaft timing gear assembly and the camshaft timing exhaust gear assembly.
Text in Illustration
*a
Turn
*b
Hold
SST
09922-10010
NOTICE:
Do not loosen the other 4 bolts. If any of the 4 bolts is loosened, replace the camshaft timing gear assembly and/or camshaft timing exhaust gear assembly with a new one.
Remove the 2 bolts and the camshaft timing gear assembly together with the No. 2 chain.
39.
REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY
Remove the bolt and No. 2 chain tensioner assembly.
40.
REMOVE CAMSHAFT BEARING CAP (for Bank 1)
Check that the camshafts are positioned as shown in the illustration.
Text in Illustration
*1
Knock Pin
*a
Front View
Uniformly loosen and remove the 8 bearing cap bolts in several steps and in the sequence shown in the illustration.
Uniformly loosen and remove the 12 bearing cap bolts in several steps in the sequence shown in the illustration.
NOTICE:
Uniformly loosen the bolts while keeping the camshaft level.
Remove the 5 camshaft bearing caps.
Remove the camshaft and No. 2 camshaft.
41.
REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH
Remove the camshaft housing sub-assembly RH by prying between the cylinder head and camshaft housing sub-assembly RH with a screwdriver.
Text in Illustration
*1
Protective Tape
NOTICE:
Be careful not to damage the contact surfaces of the cylinder head and camshaft housing sub-assembly RH.
HINT:
Tape the screwdriver tip before use.
42.
REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)
While pushing down the No. 3 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to hold the No. 3 chain tensioner assembly.
Text in Illustration
*1
Pin
*2
Plunger
*a
Push
Using SST to hold the hexagonal portion of each camshaft, loosen the bolts of the camshaft timing gear assembly and the camshaft timing exhaust gear assembly.
Text in Illustration
*a
Turn
*b
Hold
SST
09922-10010
NOTICE:
Do not loosen the other 4 bolts. If any of the 4 bolts is loosened, replace the camshaft timing gear assembly and/or camshaft timing exhaust gear assembly with a new one.
Remove the 2 bolts and the camshaft timing gear together with the No. 2 chain.
43.
REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY
Remove the bolt and No. 3 chain tensioner assembly.
44.
REMOVE CAMSHAFT BEARING CAP (for Bank 2)
Check that the camshafts are positioned as shown in the illustration.
Text in Illustration
*1
Knock Pin
*a
Front View
Uniformly loosen and remove the 8 bearing cap bolts in several steps and in the sequence shown in the illustration.
Uniformly loosen and remove the 13 bearing cap bolts in several steps and in the sequence shown in the illustration.
NOTICE:
Uniformly loosen the bolts while keeping the camshaft level.
Remove the 5 camshaft bearing caps.
Remove the No. 3 camshaft and No. 4 camshaft.
45.
REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH
Remove the camshaft housing sub-assembly LH by prying between the cylinder head and camshaft housing sub-assembly LH with a screwdriver.
Text in Illustration
*1
Protective Tape
NOTICE:
Be careful not to damage the contact surfaces of the cylinder head and camshaft housing sub-assembly LH.
HINT:
Tape the screwdriver tip before use.
46.
REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
Remove the 24 valve rocker arms from the cylinder head.
HINT:
Arrange the removed parts in the correct order.
47.
REMOVE VALVE LASH ADJUSTER ASSEMBLY
Remove the 24 valve lash adjusters from the cylinder head.
HINT:
Arrange the removed parts in the correct order.
48.
REMOVE VALVE STEM CAP
Remove the 24 valve stem caps from the cylinder head.
HINT:
Arrange the removed parts in the correct order.
49.
REMOVE CYLINDER HEAD SUB-ASSEMBLY
Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 cylinder head bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.
NOTICE:
Be careful not to drop washers into the cylinder head sub-assembly.
Cylinder head warpage or cracking could result from removing bolts in an incorrect order.
HINT:
Arrange the removed parts in the correct order.
Remove the cylinder head sub-assembly.
50.
REMOVE CYLINDER HEAD LH
Uniformly loosen and remove the 2 cylinder head set bolts in several steps and in the sequence shown in the illustration.
Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.
NOTICE:
Be careful not to drop washers into the cylinder head sub-assembly.
Cylinder head warpage or cracking could result from removing bolts in an incorrect order.
HINT:
Be sure to keep the removed parts for each installation position separate.
Remove the cylinder head LH.
51.
REMOVE CYLINDER HEAD GASKET
52.
REMOVE NO. 2 CYLINDER HEAD GASKET
53.
REMOVE NO. 1 WATER OUTLET PIPE
Disconnect the 4 wire harness clamps.
Remove the 2 nuts, bolt and No. 1 water outlet pipe.
54.
REMOVE KNOCK SENSOR
Disconnect the 2 sensor connectors.
Remove the 2 bolts and 2 sensors.
55.
REMOVE CYLINDER BLOCK WATER JACKET SPACER
Remove the 2 water jacket spacers from the cylinder block.
NOTICE:
Be sure to remove the water jacket spacers. If not, they may fall and become damaged when the cylinder block is inverted.
56.
REMOVE STRAIGHT PIN
HINT:
It is not necessary to remove the straight pin unless it is being replaced.
57.
REMOVE RING PIN
HINT:
It is not necessary to remove the ring pin unless it is being replaced.
58.
REMOVE STUD BOLT
HINT:
It is not necessary to remove the stud bolt unless it is being replaced.