2011-2016 FJ Cruiser · Service Manual ENGINE

DISASSEMBLY

Removal / installation · Vehicles built Nov 2010 – Jul 2013

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014


1. REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY

A224725
  1. Using a 24 mm deep socket wrench, remove the oil pressure switch.


2. REMOVE ENGINE COOLANT TEMPERATURE SENSOR

A224726
  1. Using a 19 mm deep socket wrench, remove the sensor.

  1. Remove the gasket from the sensor.


3. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

A221157
  1. Remove the 2 water drain cock plugs from the water drain cocks.

  1. Remove the 2 water drain cocks from the cylinder block.


4. REMOVE VVT SENSOR

A224729
  1. LH:
    Remove the 2 bolts and 2 VVT sensors.

  1. A224728
    RH:
    Remove the 2 bolts and 2 VVT sensors.


5. REMOVE CRANKSHAFT POSITION SENSOR

A224727
  1. Remove the bolt and crankshaft position sensor.


6. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY RH

A224731
  1. LH:
    Remove the 2 bolts and 2 oil control valves.

  1. A224730
    RH:
    Remove the 2 bolts and 2 oil control valves.


7. REMOVE OIL FILLER CAP HOUSING

A221161
  1. Remove the oil filler cap.

  1. Remove the 2 nuts, oil filler cap housing and gasket.


8. REMOVE NO. 1 OIL PIPE

A223691
  1. Remove the 2 oil pipe unions, gaskets and No. 1 oil pipe.

  1. Remove the oil control valve filter LH and gaskets.

    NOTICE:
    Do not touch the mesh when removing the oil control valve filter.


9. REMOVE NO. 2 OIL PIPE

A223692
  1. Remove the 2 oil pipe unions, gaskets and No. 2 oil pipe.

  1. Remove the oil control valve filter RH and gaskets.

    NOTICE:
    Do not touch the mesh when removing the oil control valve filter.


10. REMOVE OIL FILTER ELEMENT

A094910E09
  1. Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.

    Text in Illustration 
    *1
    Pipe
    *2
    Hose

  1. A222100
    Remove the oil filter drain plug.

  1. A222101E01
    Install the pipe to the oil filter cap.
    Text in Illustration 
    *1
    Cap
    *2
    Valve
    *3
    Pipe
    *4
    O-Ring
    *5
    Hose

    NOTICE:
    If the O-ring is removed with the drain plug, install the O-ring together with the pipe.

    HINT:
    Use a container to catch the draining oil.

  1. A222102
    Check that oil is drained from the oil filter. Then disconnect the pipe and remove the O-ring, as shown in the illustration.

  1. A222103E01
    Using SST, remove the oil filter cap.
    Text in Illustration 
    *1
    Oil Filter Bracket Clip
    SST
    09228-06501  

    NOTICE:
    Do not remove the oil filter bracket clip.

  1. A153538E03
    Remove the oil filter element and O-ring from the oil filter cap.
    Text in Illustration 
    *1
    O-Ring

    NOTICE:
    Be sure to remove the O-ring (for the cap) by hand, without using any tools, to prevent damage to the groove for the O-ring on the cap.


11. REMOVE OIL FILTER BRACKET

A223672E01
  1. Remove the 2 nuts, bolt, oil filter bracket and gasket.

    Text in Illustration 
    *A
    w/ Oil Cooler:
    *B
    w/o Oil Cooler:


12. REMOVE WATER INLET HOUSING

A225380
  1. Disconnect the 3 water by-pass hoses.

  1. A223012
    Remove the 5 bolts and water inlet housing.

  1. A224736
    Remove the O-ring and gasket from the water outlet pipe and water pump.

  1. A225379
    Remove the 3 water by-pass hoses.


13. REMOVE REAR WATER BY-PASS JOINT

A076534E01
  1. Remove the 2 bolts, 4 nuts, rear water by-pass joint and 2 gaskets.

  1. Remove the O-ring from the No. 1 water outlet pipe.


14. REMOVE SPARK PLUG

  1. A226864
    Remove the 6 spark plugs.


15. REMOVE VENTILATION VALVE SUB-ASSEMBLY
  1. Remove the ventilation valve hose.

  1. A224732
    Remove the ventilation valve.


16. REMOVE CRANKSHAFT PULLEY

A072947E04
  1. Using SST, hold the crankshaft pulley and loosen the pulley bolt. Further loosen the bolt until 2 or 3 threads are screwed into the crankshaft.

    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A072948E02
    Using the pulley set bolt and SST, remove the crankshaft pulley and pulley bolt.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05031)


17. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

A226542
  1. Remove the 12 bolts, seal washer, cylinder head cover and gasket.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.

  1. A223665
    Remove the 3 gaskets.


18. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

A226543
  1. Remove the 12 bolts, seal washer, cylinder head cover and gasket.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.

  1. A221164
    Remove the 3 gaskets.


19. REMOVE SPARK PLUG TUBE GASKET

A124195E04
  1. Bend the ventilation baffle plate claws on the cylinder head cover to an angle of 90° or more.

    Text in Illustration 
    *a
    Pry

  1. Remove the 6 spark plug tube gaskets.

    NOTICE:
    Be careful not to damage the gasket when removing it, as the removed gasket needs to be used when installing a new one.


20. REMOVE OIL PAN DRAIN PLUG
  1. Remove the drain plug and gasket.


21. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

A174340
  1. Remove the 10 bolts and 2 nuts.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.

  1. A174341E02
    Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.
    Text in Illustration 
    *1
    Oil Pan Seal Cutter

    NOTICE:
    Be careful not to damage the contact surfaces of the oil pans.


22. REMOVE OIL STRAINER SUB-ASSEMBLY

A245619
  1. Remove the 2 nuts, oil strainer and gasket.


23. REMOVE OIL PAN SUB-ASSEMBLY

A222173
  1. Remove the 17 bolts and 2 nuts.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.

  1. A221168E02
    Using a screwdriver, remove the oil pan by prying between the oil pan and cylinder block as shown in the illustration.
    Text in Illustration 
    *a
    LH Side:
    *b
    RH Side:
    *c
    Pry

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block or oil pan.

    HINT:
    Tape the screwdriver tip before use.

  1. A222122
    Remove the 3 O-rings from the timing chain cover.


24. REMOVE NO. 1 OIL PAN BAFFLE PLATE

A224779
  1. Remove the 6 bolts and No. 1 oil pan baffle plate.


25. REMOVE ENGINE REAR OIL SEAL RETAINER

A076247E04
  1. Remove the 5 bolts and 2 nuts.

  1. Using a screwdriver, remove the oil seal retainer by prying between the oil seal retainer and crankshaft bearing cap.

    Text in Illustration 
    *a
    Pry

    HINT:
    Tape the screwdriver tip before use.


26. REMOVE REAR CRANKSHAFT OIL SEAL

A076248E03
  1. Using a screwdriver and hammer, tap out the oil seal.

    NOTICE:
    Be careful not to damage the rear oil seal retainer.


27. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

A221169
  1. Remove the 26 bolts and the 2 nuts.

  1. A221170
    Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the contact surfaces of the timing chain cover, cylinder block or cylinder head.

  1. A221404
    Remove the oil pump gasket from the cylinder block.


28. REMOVE WATER PUMP ASSEMBLY

A221171
  1. Remove the 8 bolts, water pump and gasket.


29. REMOVE FRONT CRANKSHAFT OIL SEAL
  1. Using a screwdriver and wooden block, pry out the oil seal.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Do not damage the surface of the oil seal press fit hole.


30. SET NO. 1 CYLINDER TO TDC / COMPRESSION
  1. Temporarily tighten the pulley set bolt.

  1. A222172E01
    Turn the crankshaft clockwise to align the timing mark on the crank angle sensor plate with the RH block bore center line (TDC/compression).
    Text in Illustration 
    *1
    Center Line
    *2
    Timing Mark
    *3
    Sensor Plate

  1. A225378E01
    Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.
    If not, turn the crankshaft clockwise 1 revolution (360°) and align the timing marks as above.
    Text in Illustration 
    *1
    Timing Mark


31. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

A124589E05
  1. Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.

    Text in Illustration 
    *1
    Plunger
    *2
    Stopper Plate
    *3
    Pin

  1. Move the stopper plate downward to set the lock, and insert a pin of φ1.27 mm (0.0500 in.) into the stopper plate hole.

  1. A095165E02
    Remove the 2 bolts and No. 1 chain tensioner assembly.


32. REMOVE CHAIN TENSIONER SLIPPER

A223730
  1. Remove the chain tensioner slipper.


33. REMOVE CHAIN SUB-ASSEMBLY

A221173E01
  1. Turn the crankshaft counterclockwise 10° to loosen the chain of the crankshaft timing sprocket.

    Text in Illustration 
    *1
    Center Line
    *2
    Timing Mark
    *3
    Sensor Plate

  1. Remove the pulley set bolt.

  1. A221174
    Remove the chain sub-assembly from the crankshaft timing sprocket and place it on the crankshaft.

  1. A095682E13
    Turn the camshaft timing gear assembly on bank 1 clockwise approximately 60° so that it is as shown in the illustration. Be sure to loosen the chain subassembly between the banks.

  1. Remove the chain sub-assembly.

    Text in Illustration 
    *a
    Bank 1:


34. REMOVE NO. 1 IDLE GEAR SHAFT

A221175
  1. Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, No. 1 idle gear and No. 1 idle gear shaft.


35. REMOVE NO. 1 CHAIN VIBRATION DAMPER

A223642
  1. Remove the 2 bolts and No. 1 chain vibration damper.


36. REMOVE NO. 2 CHAIN VIBRATION DAMPER

A221176
  1. Remove the 2 No. 2 chain vibration dampers.


37. REMOVE CRANKSHAFT TIMING SPROCKET

A158530E01
  1. Remove the crankshaft timing sprocket.


38. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)

A221132E01
  1. While raising the No. 2 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to hold the No. 2 chain tensioner assembly.

    Text in Illustration 
    *1
    Pin
    *2
    Plunger
    *a
    Push

  1. A221177E01
    Using SST to hold the hexagonal portion of each camshaft, loosen the bolts of the camshaft timing gear assembly and the camshaft timing exhaust gear assembly.
    Text in Illustration 
    *a
    Turn
    *b
    Hold
    SST
    09922-10010  

    NOTICE:
    Do not loosen the other 4 bolts. If any of the 4 bolts is loosened, replace the camshaft timing gear assembly and/or camshaft timing exhaust gear assembly with a new one.

  1. Remove the 2 bolts and the camshaft timing gear assembly together with the No. 2 chain.


39. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

A221178
  1. Remove the bolt and No. 2 chain tensioner assembly.


40. REMOVE CAMSHAFT BEARING CAP (for Bank 1)

A129700E06
  1. Check that the camshafts are positioned as shown in the illustration.

    Text in Illustration 
    *1
    Knock Pin
    *a
    Front View

  1. A221179E01
    Uniformly loosen and remove the 8 bearing cap bolts in several steps and in the sequence shown in the illustration.

  1. A221180E01
    Uniformly loosen and remove the 12 bearing cap bolts in several steps in the sequence shown in the illustration.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshaft level.

  1. Remove the 5 camshaft bearing caps.

  1. Remove the camshaft and No. 2 camshaft.


41. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH

A221181E01
  1. Remove the camshaft housing sub-assembly RH by prying between the cylinder head and camshaft housing sub-assembly RH with a screwdriver.

    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and camshaft housing sub-assembly RH.

    HINT:
    Tape the screwdriver tip before use.


42. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)

A221182E01
  1. While pushing down the No. 3 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to hold the No. 3 chain tensioner assembly.

    Text in Illustration 
    *1
    Pin
    *2
    Plunger
    *a
    Push

  1. A223637E01
    Using SST to hold the hexagonal portion of each camshaft, loosen the bolts of the camshaft timing gear assembly and the camshaft timing exhaust gear assembly.
    Text in Illustration 
    *a
    Turn
    *b
    Hold
    SST
    09922-10010  

    NOTICE:
    Do not loosen the other 4 bolts. If any of the 4 bolts is loosened, replace the camshaft timing gear assembly and/or camshaft timing exhaust gear assembly with a new one.

  1. Remove the 2 bolts and the camshaft timing gear together with the No. 2 chain.


43. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

A221183
  1. Remove the bolt and No. 3 chain tensioner assembly.


44. REMOVE CAMSHAFT BEARING CAP (for Bank 2)

A223636E01
  1. Check that the camshafts are positioned as shown in the illustration.

    Text in Illustration 
    *1
    Knock Pin
    *a
    Front View

  1. A221184E01
    Uniformly loosen and remove the 8 bearing cap bolts in several steps and in the sequence shown in the illustration.

  1. A221185E01
    Uniformly loosen and remove the 13 bearing cap bolts in several steps and in the sequence shown in the illustration.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshaft level.

  1. Remove the 5 camshaft bearing caps.

  1. Remove the No. 3 camshaft and No. 4 camshaft.


45. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH

A221186E01
  1. Remove the camshaft housing sub-assembly LH by prying between the cylinder head and camshaft housing sub-assembly LH with a screwdriver.

    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and camshaft housing sub-assembly LH.

    HINT:
    Tape the screwdriver tip before use.


46. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
  1. Remove the 24 valve rocker arms from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.


47. REMOVE VALVE LASH ADJUSTER ASSEMBLY
  1. Remove the 24 valve lash adjusters from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.


48. REMOVE VALVE STEM CAP
  1. Remove the 24 valve stem caps from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.


49. REMOVE CYLINDER HEAD SUB-ASSEMBLY

A221092E01
  1. Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 cylinder head bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.

    NOTICE:
    1. Be careful not to drop washers into the cylinder head sub-assembly.
    2. Cylinder head warpage or cracking could result from removing bolts in an incorrect order.

    HINT:
    Arrange the removed parts in the correct order.

  1. Remove the cylinder head sub-assembly.


50. REMOVE CYLINDER HEAD LH

A221093E01
  1. Uniformly loosen and remove the 2 cylinder head set bolts in several steps and in the sequence shown in the illustration.

  1. A221094E01
    Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.

    NOTICE:
    1. Be careful not to drop washers into the cylinder head sub-assembly.
    2. Cylinder head warpage or cracking could result from removing bolts in an incorrect order.

    HINT:
    Be sure to keep the removed parts for each installation position separate.

  1. Remove the cylinder head LH.


51. REMOVE CYLINDER HEAD GASKET

52. REMOVE NO. 2 CYLINDER HEAD GASKET

53. REMOVE NO. 1 WATER OUTLET PIPE

  1. A178539
    Disconnect the 4 wire harness clamps.

  1. Remove the 2 nuts, bolt and No. 1 water outlet pipe.


54. REMOVE KNOCK SENSOR

  1. A075662
    Disconnect the 2 sensor connectors.

  1. Remove the 2 bolts and 2 sensors.


55. REMOVE CYLINDER BLOCK WATER JACKET SPACER

A225372
  1. Remove the 2 water jacket spacers from the cylinder block.

    NOTICE:
    Be sure to remove the water jacket spacers. If not, they may fall and become damaged when the cylinder block is inverted.


56. REMOVE STRAIGHT PIN

HINT:
It is not necessary to remove the straight pin unless it is being replaced.


57. REMOVE RING PIN

HINT:
It is not necessary to remove the ring pin unless it is being replaced.


58. REMOVE STUD BOLT

HINT:
It is not necessary to remove the stud bolt unless it is being replaced.

← DISASSEMBLY (Aug 2009 – Oct 2010)DISASSEMBLY (Aug 2013 – Jul 2014) →