2011-2016 FJ Cruiser · Service Manual ENGINE

DISASSEMBLY

Removal / installation · Vehicles built Jul 2007 – Jul 2009

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

HINT:
  1. Thoroughly clean all the disassembled parts before reassembly.
  2. Before installing the parts, apply new engine oil to all sliding and rotating surfaces.
  3. Replace all gaskets, O-rings and oil seals with new parts.


1. REMOVE ENGINE HANGERS

A072941E02
  1. Remove the 2 bolts and No. 1 engine hanger.

  1. Remove the 2 bolts and No. 2 engine hanger.


2. REMOVE ENGINE COOLANT TEMPERATURE SENSOR

A126460
  1. Remove the engine coolant temperature sensor and gasket.


3. REMOVE WATER BY-PASS JOINT REAR

A121043
  1. Remove the 2 bolts, 4 nuts and the water by-pass rear joint.

  1. Remove the 2 gaskets from the cylinder head.

  1. Remove the O-ring from the outlet pipe.


4. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 1)

A126464
  1. Remove the bolt and camshaft timing oil control valve.


5. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 2)

A126463
  1. Remove the bolt and camshaft timing oil control valve.


6. REMOVE OIL FILTER SUB-ASSEMBLY

A122120E01
  1. Remove the drain pipe cap.

  1. While removing the oil filter with SST, catch the oil from the oil filter with a container.

    SST
    09228-07501  

  1. Install the drain pipe cap.


7. REMOVE OIL FILTER UNION (w/o Oil Cooler)
  1. Using a 12 mm hexagon wrench, remove the oil filter union.


8. REMOVE OIL COOLER ASSEMBLY (w/ Oil Cooler)
  1. Disconnect the 2 hoses from the oil cooler.

  1. A076453E02
    Remove the union bolt, plate washer and oil cooler.

  1. Remove the O-ring from the oil cooler.


9. REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY
  1. Using a 24 mm deep socket wrench, remove the oil pressure switch.


10. REMOVE OIL FILTER BRACKET SUB-ASSEMBLY

A120414
  1. Remove the 3 bolts, 2 nuts and the oil filter bracket.

  1. Remove the gasket.

  1. Remove the 2 stud bolts.


11. REMOVE WITH THERMOSTAT WATER INLET SUB-ASSEMBLY

A121042
  1. Remove the 3 nuts and the water inlet with thermostat.

  1. Remove the O-ring.


12. REMOVE NO. 3 WATER BY-PASS HOSE
  1. Loosen the 2 clamps and remove the No. 3 water by-pass hose.


13. REMOVE NO. 2 WATER BY-PASS HOSE
  1. Loosen the 2 clamps and remove the No. 2 water by-pass hose.


14. REMOVE WATER BY-PASS HOSE
  1. Loosen the 2 clamps and remove the water by-pass hose.


15. REMOVE WATER INLET

A126462
  1. Remove the 5 bolts and water inlet.

  1. Remove the O-ring from the outlet pipe.

  1. Remove the gasket.


16. REMOVE SPARK PLUG
  1. Using a spark plug wrench, remove the 6 spark plugs.


17. REMOVE OIL LEVEL GAUGE GUIDE
  1. Remove the bolt, then pull out the oil level gauge guide.

  1. Remove the O-ring from the oil level gauge guide.


18. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY
  1. Remove the 2 water drain cocks.


19. REMOVE VVT SENSOR

G036794E03
  1. Remove the 2 bolts, then remove the 2 VVT sensors.


20. REMOVE CRANKSHAFT POSITION SENSOR

G036795E01
  1. Remove the bolt, then remove the crankshaft position sensor.


21. REMOVE OIL CONTROL VALVE FILTER

A072942E07
  1. Remove the plug and filter, then remove the gasket from each cylinder head.


22. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

A072944E01
  1. Remove the 10 bolts, 3 seal washers and 2 nuts, then remove the cylinder head cover.

  1. Remove the gasket from the cylinder head cover.

  1. Remove the ventilation valve from the cylinder head cover.


23. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

A072943E01
  1. Remove the 10 bolts, 3 seal washers and 2 nuts, then remove the cylinder head cover.

  1. Remove the gasket from the cylinder head cover.


24. REMOVE CRANKSHAFT PULLEY

A072945E01
  1. Turn the crankshaft pulley until its groove and the "0" timing mark of the timing chain cover are aligned.

  1. G036289E04
    Check that the timing marks of the camshaft timing gears are aligned with the timing marks located on the No. 1 and No. 2 bearing caps as shown in the illustration.
    If not, turn the crankshaft 1 complete revolution (360°) and align the timing marks as above.

  1. A072947E02
    Using SST, fix the pulley and loosen the pulley bolt.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A072948E01
    Using the pulley set bolt and SST, remove the crankshaft pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05030)


25. REMOVE OIL PAN DRAIN PLUG
  1. Remove the drain plug and gasket.


26. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

  1. A126351
    Remove the 10 bolts and 2 nuts.

  1. A072950E02
    Insert the blade of SST between the oil pan and oil pan No. 2, then cut off applied sealer and remove oil pan No. 2.

    NOTICE:
    1. Be careful not to damage the contact surface of the oil pan and oil pan No. 2.
    2. Be careful not to damage the oil pan No. 2 flange.


27. REMOVE OIL STRAINER SUB-ASSEMBLY

  1. A072951E03
    Remove the 2 nuts, then remove the oil strainer and gasket.


28. REMOVE OIL PAN SUB-ASSEMBLY

A126353
  1. Remove the 4 stud bolts from the oil pan.

  1. A126352
    Remove the 17 bolts and 2 nuts.

  1. G036806E01
    Using a screwdriver, remove the oil pan by prying between the oil pan and cylinder block in the sequence shown.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.

  1. Remove the O-ring from the oil pump.


29. REMOVE WATER PUMP ASSEMBLY

A072954E01
  1. Remove the 17 bolts, then remove the water pump and gasket.


30. REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY

G036855E03
  1. Remove the 15 bolts and 2 nuts.

  1. G036859E01
    Remove the timing chain cover by prying between the timing chain cover, cylinder head and cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the timing chain cover, cylinder block and cylinder head.

  1. Remove the 4 bolts and timing chain cover plate.

  1. Remove the O-ring from the cylinder head LH.


31. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

NOTICE:
  1. Never rotate the crankshaft with the chain tensioner removed.
  2. When rotating the camshaft with the timing chain removed, rotate the crankshaft counterclockwise 40° from the TDC first.

  1. A072958E02
    While turning the stopper plate of the tensioner upward, push in the plunger of the chain tensioner as shown in the illustration.

  1. While turning the stopper plate of the tensioner downward, insert a bar of φ 3.5 mm (0.138 in.) into the holes in the stopper plate and tensioner to fix the stopper plate.

  1. Remove the 2 bolts, then remove the chain tensioner.


32. REMOVE CHAIN TENSIONER SLIPPER

33. REMOVE NO. 1 IDLE GEAR

G036860E01
  1. Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, No. 1 idle gear and No. 1 idle gear shaft.


34. REMOVE NO. 2 CHAIN VIBRATION DAMPER

G036844E01
  1. Remove the 2 No. 2 chain vibration dampers.


35. REMOVE CHAIN SUB-ASSEMBLY

36. REMOVE CRANKSHAFT TIMING GEAR OR SPROCKET

37. REMOVE NO. 1 CHAIN VIBRATION DAMPER

G036808E01
  1. Remove the 2 bolts, then remove the No. 1 chain vibration damper.


38. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)

G036850E01
  1. While raising chain tensioner No. 2 upward, insert a pin of φ 1.0 mm (0.039 in.) into the hole to fix it.

  1. G036834E01
    Hold the hexagonal portion of the camshaft with a wrench, and remove the 2 bolts, camshaft timing gear, camshaft timing gear assembly and No. 2 timing chain.

    NOTICE:
    1. Be careful not to damage the cylinder head and valve lifter with the wrench.
    2. Do not disassemble the camshaft timing gear assembly.


39. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

A072962E01
  1. Remove the bolt, then remove the No. 2 chain tensioner.


40. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)

G036835E01
  1. While pushing down the No. 3 chain tensioner, insert a pin of φ 1.0 mm (0.039 in.) into the hole to fix it.

  1. G036836E01
    Hold the hexagonal portion of the camshaft with a wrench, and remove the 2 bolts, camshaft timing gear, camshaft timing gear assembly and No. 2 timing chain.

    NOTICE:
    1. Be careful not to damage the cylinder head and valve lifter with the wrench.
    2. Do not disassemble the camshaft timing gear assembly.


41. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

A072965E01
  1. Remove the bolt, then remove the No. 3 chain tensioner.


42. INSPECT CAMSHAFT THRUST CLEARANCE

A075624E01
  1. Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

    Standard thrust clearance:
    0.04 to 0.09 mm (0.016 to 0.035 in.)

    Maximum thrust clearance:
    0.11 mm (0.0043 in.)

    If the thrust clearance is greater than the maximum, replace the camshafts.
    If necessary, replace the camshaft bearing caps and cylinder head as a set.


43. REMOVE CAMSHAFTS

NOTICE:
Keep the camshaft level while it is being removed. The camshaft thrust clearance is very small and failing to keep it level could crack or damage the cylinder head journal surface, which receives the thrust force. This could subsequently lead the camshaft to seize or break. Perform the following steps to avoid such problems.

  1. A072966E07
    Remove the camshafts of bank 1.

    1. Rotate the camshafts counterclockwise using a wrench so that cam lobes of No. 1 cylinder face in the directions as shown in the illustration.

    2. A072967E20
      Using several steps, uniformly loosen and remove the 16 bearing cap bolts in the sequence shown in the illustration.

    3. Remove the 8 bearing caps, then remove the 2 camshafts.

  1. A072968E20
    Remove the camshafts of bank 2.

    1. Using several steps, uniformly loosen and remove the 16 bearing cap bolts in the sequence shown in the illustration.

    2. Remove the 8 bearing caps, then remove the 2 camshafts.


44. REMOVE NO. 1 CAMSHAFT BEARING
  1. Remove the No. 1 camshaft bearing from the No. 1 camshaft bearing cap.


45. REMOVE NO. 2 CAMSHAFT BEARING

A076279E01
  1. Remove the No. 2 camshaft bearing from the cylinder head for bank 1.


46. INSPECT CAMSHAFT OIL CLEARANCE

A075622E02
  1. Clean the camshaft bearing caps, camshaft bearings and camshaft journals.

  1. Install the camshaft bearing.

  1. Place the camshaft on the cylinder head.

  1. Lay a strip of Plastigage across each camshaft journal.

  1. Install the camshaft bearing caps.

    NOTICE:
    Do not turn the camshafts.

  1. Remove the camshaft bearing caps.

  1. A075623E01
    Measure the Plastigage at its widest point.

    Standard oil clearance (Bank 1):
    Camshaft Bearing Cap
    Specification
    No. 1 (Intake)
    0.008 to 0.038 mm (0.0003 to 0.0015 in.)
    No. 1 (Exhaust)
    0.040 to 0.079 mm (0.0016 to 0.0031 in.)
    Others
    0.025 to 0.062 mm (0.0010 to 0.0024 in.)

    Standard oil clearance (Bank 2):
    Camshaft Bearing Cap
    Specification
    No. 1
    0.040 to 0.079 mm (0.0016 to 0.0031 in.)
    Others
    0.025 to 0.062 mm (0.0010 to 0.0024 in.)

    Maximum oil clearance (Bank 1):
    Camshaft Bearing Cap
    Specification
    No. 1 (Intake)
    0.07 mm (0.0028 in.)
    Others
    0.10 mm (0.0039 in.)

    Maximum oil clearance (Bank 2):
    0.10 mm (0.0039 in.)

    If the oil clearance is greater than the maximum, replace the camshaft bearings and/or camshafts.
    If necessary, replace the camshaft bearing caps and cylinder head together.
    Reference 
    Cylinder head journal bore diameter
    40.009 to 40.017 mm (1.5752 to 1.5755 in.)
    Camshaft bearing center wall thickness (Mark "2")
    2.004 to 2.008 mm (0.0789 to 0.0791 in.)
    Camshaft journal diameter
    35.971 to 35.985 mm (1.4165 to 1.4167 in.)

  1. Remove the Plastigage completely.

  1. Remove the camshafts.

  1. Remove the camshaft bearing.


47. REMOVE CYLINDER HEADS

  1. A072970E09
    Using several steps, loosen the 8 cylinder head bolts on each cylinder head with a 10 mm bi-hexagon wrench in the sequence shown in the illustration. Remove the 16 cylinder head bolts, then remove the plate washers.

    NOTICE:
    1. Be careful not to drop the plate washers into the cylinder head.
    2. Cylinder head warpage or cracking could result from removing the bolts in the wrong order.

  1. A072971E01
    Lift the cylinder head from the dowels on the cylinder block, and place the 2 cylinder heads on wooden blocks on a bench.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and cylinder block.

    HINT:
    If the cylinder head is difficult to remove, pry between the cylinder head and cylinder block with a screwdriver.

  1. Remove the bank 1 and bank 2 cylinder head gaskets.


48. REMOVE NO. 1 WATER OUTLET PIPE

G036807E01
  1. Separate the knock sensor wire.

  1. Remove the 3 bolts, then remove the water outlet pipe.


49. REMOVE KNOCK SENSOR

A076270E01
  1. Disconnect the 2 knock sensor connectors.

  1. Remove the 2 bolts, then remove the 2 knock sensors.


50. REMOVE REAR ENGINE OIL SEAL RETAINER

A076247E02
  1. Remove the 5 bolts and 2 nuts.

  1. Using a screwdriver, remove the oil seal retainer by prying between the oil seal retainer and crankshaft bearing cap.


51. INSPECT CONNECTING ROD THRUST CLEARANCE

A075147E01
  1. Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.

    Standard thrust clearance:
    0.15 to 0.30 mm (0.0059 to 0.0118 in.)

    Maximum thrust clearance:
    0.35 mm (0.0138 in.)


52. INSPECT CONNECTING ROD OIL CLEARANCE
  1. Check the matchmarks on the connecting rod and cap are aligned to ensure correct assembly.

  1. A075150E01
    Remove the 2 connecting rod cap bolts.

  1. Clean the crank pin, bearing and connecting rod.

  1. Check the crank pin and bearing for any pits and scratches.

  1. A075148E02
    Lay a strip of plastigage across the crank pin.

  1. A075149E02
    Check that the protrusion of the connecting rod cap is facing in the correct direction.

  1. Apply a light coat of engine oil to the threads of the connecting rod cap bolts.

  1. A075150E01
    Tighten the bolts alternately to the specified torque.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }

  1. A075151E03
    Mark the front side of the each connecting cap bolt with paint.

  1. Retighten the cap bolts 90° as shown in the illustration.

    NOTICE:
    Do not turn the crankshaft.

  1. Remove the 2 bolts, connecting rod cap and lower bearing.

  1. A075152E02
    Measure the plastigage at its widest point.

    Standard oil clearance:
    0.026 to 0.046 mm (0.0010 to 0.0018 in.)

    Maximum oil clearance:
    0.066 mm (0.0025 in.)

    NOTICE:
    Completely remove the plastigage.

  1. A126508E01
    When replacing the bearing, replace it with one with the same number as marked on the connecting rod. There are 4 sizes of standard bearings, marked "1", "2", "3" and "4".

    HINT:
    Standard bearing center wall thickness

    Mark
    mm (in.)
    "1"
    1.484 to 1.487 (0.0584 to 0.0585)
    "2"
    1.487 to 1.490 (0.0585 to 0.0587)
    "3"
    1.490 to 1.493 (0.0587 to 0.0588)
    "4"
    1.493 to 1.496 (0.0588 to 0.0589)

  1. A075150E01
    Remove the 2 connecting rod cap bolts.


53. REMOVE PISTON SUB-ASSEMBLY WITH CONNECTING ROD

A076043E01
  1. Using a ridge reamer, remove all the carbon from the top of the cylinder.

  1. Push in the piston, connecting rod assembly and upper bearing through the top of the cylinder block.

    HINT:
    1. Keep the bearings, connecting rod and cap together.
    2. Arrange the piston and connecting rod in the correct order.


54. REMOVE CONNECTING ROD BEARING

55. REMOVE PISTON RING SET

A076044E01
  1. Using a piston ring expander, remove the 2 compression rings.

  1. Remove the 2 side rails and oil ring by hand.


56. REMOVE HOLE SNAP RING

P012403E01
  1. Using a small screwdriver, pry out the 2 snap rings.


57. REMOVE WITH PISTON SUB-ASSEMBLY

A076045E07
  1. Gradually heat the piston to approximately 80°C (176°F).

  1. A076046E01
    Using a plastic-faced hammer and brass bar, lightly tap out the piston pin and remove the connecting rod.

    HINT:
    1. The piston and pin are a matched set.
    2. Arrange the pistons, pins, rings, connecting rods and bearings in the correct order.


58. INSPECT CRANKSHAFT THRUST CLEARANCE

A076047E01
  1. Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.

    Standard thrust clearance:
    0.04 to 0.24 mm (0.0016 to 0.0094 in.)

    Maximum thrust clearance:
    0.30 mm (0.0118 in.)

    If the thrust clearance is greater than the maximum, replace the pair of the thrust washers or crankshaft.

    HINT:
    Thrust washer thickness:
    1.93 to 1.98 mm (0.0760 to 0.0780 in.)


59. INSPECT CRANKSHAFT OIL CLEARANCE

A076048E01
  1. Using several steps, uniformly loosen and remove the 8 main bearing cap bolts and seal washers in the sequence shown in the illustration.

  1. A076049E01
    Using several steps, uniformly loosen and remove the 16 main bearing cap bolts in the sequence shown in the illustration.

  1. A121032E01
    Using a screwdriver, pry out the main bearing caps. Remove the 4 main bearing caps and lower bearings.

    NOTICE:
    1. Pull up the main bearing cap by turning it to the right and left little by little.
    2. Be careful not to damage the joint surfaces of the cylinder block and the main bearing cap.

  1. A076066E02
    Lay a strip of plastigage across each journal.

  1. A076067E01
    Examine the front marks and numbers, check the sequence order is as shown and install the bearing caps onto the cylinder block.

  1. Apply a light coat of engine oil to the threads of bearing cap bolts.

  1. Temporarily install the 8 main bearing cap bolts in the inside positions.

  1. A076069E02
    Install the main bearing caps. Tighten the 2 bolts for each bearing cap until the clearance between the bearing cap and the cylinder block is under 6 mm (0.23 in.).

  1. A076070E01
    Using a plastic-faced hammer, lightly tap the bearing cap to ensure a proper fit.

  1. Apply a light coat of engine oil to the threads of main bearing cap bolts.

  1. A076071E04
    Install the 16 main bearing cap bolts. Using several steps, tighten the bolts uniformly in the sequence shown in the illustration.

    Torque:
    61 N*m{ 622 kgf*cm , 45 ft.*lbf }

  1. A076072E03
    Mark the front side of the bearing cap bolts with paint.

  1. Retighten the bearing cap bolts 90° in the sequence as shown.

  1. Check that the painted mark is now at a 90° angle from the front.

    NOTICE:
    Do not turn the crankshaft.

  1. A075843E03
    Install the 8 main bearing cap bolts. Using several steps, tighten the bolts uniformly in the sequence shown in the illustration.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. Remove the main bearing caps.

  1. A075844E01
    Measure the Plastigage at its widest point.

    Standard oil clearance:
    0.018 to 0.030 mm (0.0007 to 0.0012 in.)

    Maximum clearance:
    0.046 mm (0.0018 in.)

    If the oil clearance is greater than the maximum, replace the bearings. If necessary, replace the crankshaft.

    NOTICE:
    Completely remove the plastigage.

  1. A075845E03
    Replace the bearing with the same number. If the number of the bearing cannot be determined, select the correct bearing by adding together the numbers imprinted on the cylinder block and crankshaft, then refer to the table below for the appropriate bearing number. There are 5 size of standard bearings, marked "1", "2", "3", "4" and "5".

    Journal bearing:
    Cylinder block (A) + Crankshaft
    0 -5
    6 -11
    12 -17
    18 - 23
    24 - 28
    Use Bearing
    "1"
    "2"
    "3"
    "4"
    "5"

    HINT:
    EXAMPLE
    Cylinder block "11" (A) + Crankshaft "06" (B)
    =Total number 17 (Use bearing "3")

    Item
    Mark
    mm (in.)
    Cylinder block main journal bore diameter (A)
    "00"
    77.000 (3.0315)
    "01"
    77.001 (3.0315)
    "02"
    77.002 (3.0316)
    "03"
    77.003 (3.0316)
    "04"
    77.004 (3.0317)
    "05"
    77.005 (3.0317)
    "06"
    77.006 (3.0317)
    "07"
    77.007 (3.0318)
    "08"
    77.008 (3.0318)
    "09"
    77.009 (3.0319)
    "10"
    77.010 (3.0319)
    "11"
    77.011 (3.0319)
    "12"
    77.012 (3.0320)
    "13"
    77.013 (3.0320)
    "14"
    77.014 (3.0320)
    "15"
    77.015 (3.0321)
    "16"
    77.016 (3.0321)
    Crankshaft main journal diameter (B)
    "00"
    71.999 to 72.000 (2.8346 to 2.8346)
    "01"
    71.998 to 71.999 (2.8346 to 2.8346)
    "02"
    71.997 to 71.998 (2.8345 to 2.8346)
    "03"
    71.996 to 71.997 (2.8345 to 2.8346)
    "04"
    71.995 to 71.996 (2.8344 to 2.8345)
    "05"
    71.994 to 71.995 (2.8344 to 2.8344)
    "06"
    71.993 to 71.994 (2.8343 to 2.8344)
    "07"
    71.992 to 71.993 (2.8343 to 2.8343)
    "08"
    71.991 to 71.992 (2.8343 to 2.8343)
    "09"
    71.990 to 71.991 (2.8343 to 2.8343)
    "10"
    71.989 to 71.990 (2.8342 to 2.8343)
    "11"
    71.988 to 71.989 (2.8342 to 2.8342)
    Standard bearing center wall thickness
    "1"
    2.488 to 2.491 (0.0980 to 0.0981)
    "2"
    2.491 to 2.494 (0.0981 to 0.0982)
    "3"
    2.494 to 2.497 (0.0982 to 0.0983)
    "4"
    2.497 to 2.500 (0.0982 to 0.0984)
    "5"
    2.500 to 2.503 (0.0984 to 0.0985)


60. REMOVE CRANKSHAFT

A076048E01
  1. Using several steps, uniformly loosen and remove the 8 main bearing cap bolts and seal washers in the sequence shown in the illustration.

  1. A076049E01
    Using several steps, uniformly loosen and remove the 16 main bearing cap bolts in the sequence shown in the illustration.

  1. A121032E01
    Using a screwdriver, pry out the main bearing caps. Remove the 4 main bearing caps and lower bearings.

    NOTICE:
    1. Pull up the main bearing cap by turning it to the right and left little by little.
    2. Be careful not to damage the joint surfaces of the cylinder block and the main bearing cap.

  1. Remove the crankshaft.


61. REMOVE CRANKSHAFT THRUST WASHER SET

62. REMOVE CRANKSHAFT BEARING

63. REMOVE NO. 1 SUB-ASSEMBLY OIL NOZZLE

A076051E01
  1. Using a 5 mm socket hexagon wrench, remove the 3 hexagon cap head blots and the 3 oil nozzles.


64. REMOVE OIL JET

65. REMOVE TIGHT PLUG

66. REMOVE STRAIGHT PIN

67. REMOVE STUD BOLT

A126355

68. DISASSEMBLY CYLINDER HEAD SUB-ASSEMBLY
Refer to the procedures up to "DISASSEMBLY CYLINDER HEAD" (Click here).
← REMOVAL (from Aug 2014)DISASSEMBLY (Aug 2009 – Oct 2010) →