Remove the 12 bolts, seal washer and cylinder head cover sub-assembly LH from the camshaft housing sub-assembly LH and timing chain cover sub-assembly.
Text in Illustration
*1
Seal Washer
HINT:
Make sure the removed parts are returned to the same places they were removed from.
Remove the No. 2 cylinder head cover gasket from the cylinder head cover sub-assembly LH.
Remove the 3 gaskets from the camshaft bearing caps.
19.
REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
Remove the 12 bolts, seal washer and cylinder head cover sub-assembly from the camshaft housing sub-assembly RH and timing chain cover sub-assembly.
Text in Illustration
*1
Seal Washer
HINT:
Make sure the removed parts are returned to the same places they were removed from.
Remove the cylinder head cover gasket from the cylinder head cover sub-assembly.
Remove the 3 gaskets from the camshaft bearing caps.
20.
REMOVE SPARK PLUG TUBE GASKET
Bend the ventilation baffle plate claws on the cylinder head cover sub-assembly to an angle of 90° or more.
Text in Illustration
*a
Bend
Remove the 6 spark plug tube gaskets from the cylinder head cover sub-assembly and cylinder head cover sub-assembly LH.
NOTICE:
Be careful not to damage the spark plug tube gasket when removing it, as the removed spark plug tube gasket needs to be used when installing a new one.
21.
REMOVE OIL PAN DRAIN PLUG
Remove the oil pan drain plug and gasket from the No. 2 oil pan sub-assembly.
22.
REMOVE NO. 2 OIL PAN SUB-ASSEMBLY
Remove the 10 bolts and 2 nuts.
HINT:
Make sure the removed parts are returned to the same places they were removed from.
Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.
Text in Illustration
*1
Oil Pan Seal Cutter
NOTICE:
Be careful not to damage the contact surfaces of the oil pans.
23.
REMOVE OIL STRAINER SUB-ASSEMBLY
Remove the 2 nuts, oil strainer and gasket.
24.
REMOVE OIL PAN SUB-ASSEMBLY
Remove the 17 bolts and 2 nuts.
HINT:
Make sure the removed parts are returned to the same places they were removed from.
Using a screwdriver, remove the oil pan by prying between the oil pan and cylinder block as shown in the illustration.
Text in Illustration
*a
LH Side:
*b
RH Side:
*c
Pry
NOTICE:
Be careful not to damage the contact surfaces of the cylinder block or oil pan.
HINT:
Tape the screwdriver tip before use.
Remove the 3 O-rings from the timing chain cover.
25.
REMOVE NO. 1 OIL PAN BAFFLE PLATE
Remove the 6 bolts and No. 1 oil pan baffle plate from the oil pan sub-assembly.
26.
REMOVE ENGINE REAR OIL SEAL RETAINER
Remove the 5 bolts and 2 nuts from the cylinder block sub-assembly.
Using a screwdriver with its tip wrapped in protective tape, remove the engine rear oil seal retainer by prying between the engine rear oil seal retainer and crankshaft bearing cap.
Text in Illustration
*a
Protective Tape
*b
Pry
27.
REMOVE REAR CRANKSHAFT OIL SEAL
Using a screwdriver and hammer, tap out the rear crankshaft oil seal from the engine rear oil seal retainer.
NOTICE:
Be careful not to damage the engine rear oil seal retainer.
28.
REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
Remove the 26 bolts and the 2 nuts.
Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.
HINT:
Tape the screwdriver tip before use.
NOTICE:
Be careful not to damage the contact surfaces of the timing chain cover, cylinder block or cylinder head.
Remove the oil pump gasket from the cylinder block.
29.
REMOVE TIMING CHAIN COVER PLATE
Remove the 4 bolts, timing chain cover plate and gasket.
30.
REMOVE ENGINE WATER PUMP ASSEMBLY
Remove the 8 bolts, engine water pump assembly and gasket from the timing chain cover sub-assembly.
31.
REMOVE FRONT CRANKSHAFT OIL SEAL
Using a screwdriver and wooden block, pry out the oil seal.
HINT:
Tape the screwdriver tip before use.
NOTICE:
Do not damage the surface of the oil seal press fit hole.
32.
SET NO. 1 CYLINDER TO TDC / COMPRESSION
Temporarily tighten the crankshaft pulley bolt to the crankshaft.
Turn the crankshaft clockwise to align the timing mark on the crank angle sensor plate with the RH cylinder block bore center line (TDC/compression).
Text in Illustration
*1
Crank Angle Sensor Plate
*a
RH Cylinder Block Bore Center Line
*b
Timing Mark
Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the camshaft bearing caps as shown in the illustration. If not, turn the crankshaft clockwise 1 revolution (360°) and align the timing marks as above.
Text in Illustration
*a
Timing Mark
33.
REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.
Text in Illustration
*1
Plunger
*2
Stopper Plate
*a
Push
*b
Pin of 12.7 mm (0.05 in.) diameter
Move the stopper plate downward to set the lock, and insert a pin of 1.27 mm (0.05 in.) diameter into the stopper plate hole.
Remove the 2 bolts and No. 1 chain tensioner assembly from the cylinder head sub-assembly.
34.
REMOVE CHAIN TENSIONER SLIPPER
Remove the chain tensioner slipper from the cylinder block sub-assembly.
35.
REMOVE CHAIN SUB-ASSEMBLY
Turn the crankshaft counterclockwise 10° to loosen the chain sub-assembly of the crankshaft timing sprocket.
Text in Illustration
*1
Crank Angle Sensor Plate
*a
RH Cylinder Block Bore Center Line
*b
Timing Mark
Remove the crankshaft pulley bolt from the crankshaft.
Remove the chain sub-assembly from the crankshaft timing sprocket and place it on the crankshaft timing sprocket.
Turn the camshaft timing gear assembly on bank 1 clockwise approximately 60° so that it is as shown in the illustration. Be sure to loosen the chain sub-assembly between the banks.
Remove the chain sub-assembly.
Text in Illustration
*a
Bank 1
Clockwise Approximately 60°
36.
REMOVE NO. 1 IDLE GEAR SHAFT
Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, No. 1 idle gear and No. 1 idle gear shaft from the cylinder block sub-assembly.
37.
REMOVE NO. 1 CHAIN VIBRATION DAMPER
Remove the 2 bolts and No. 1 chain vibration damper from the cylinder head LH and cylinder block sub-assembly.
38.
REMOVE NO. 2 CHAIN VIBRATION DAMPER
Remove the 2 No. 2 chain vibration dampers from the cylinder head sub-assembly and cylinder head LH.
39.
REMOVE CRANKSHAFT TIMING SPROCKET
Remove the crankshaft timing sprocket from the crankshaft.
40.
REMOVE CRANKSHAFT TIMING GEAR KEY
Remove the crankshaft timing gear key from the crankshaft.
41.
REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 1)
While raising the plunger, insert a pin of 1.0 mm (0.0394 in.) diameter into the plunger hole to hold the No. 2 chain tensioner assembly.
Text in Illustration
*1
Plunger
*a
Pin of 1.0 mm (0.0394 in.) diameter
*b
Rise
Using SST to hold the hexagonal portion of each camshaft, loosen the bolts of the camshaft timing gear assembly and camshaft timing exhaust gear assembly RH.
Text in Illustration
*a
Turn
*b
Hold
SST
09922-10010
NOTICE:
Do not loosen the other 4 bolts. If any of the 4 bolts is loosened, replace the camshaft timing gear assembly and/or camshaft timing exhaust gear assembly RH with a new one.
Remove the 2 bolts from the camshaft and No. 2 camshaft.
Remove the camshaft timing gear assembly and camshaft timing exhaust gear assembly RH together with the No. 2 chain sub-assembly from the camshaft and No. 2 camshaft.
42.
REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY
Remove the bolt and No. 2 chain tensioner assembly from the camshaft housing sub-assembly RH.
43.
REMOVE CAMSHAFT BEARING CAP (for Bank 1)
Check that the camshafts are positioned as shown in the illustration.
Text in Illustration
*1
Knock Pin
*a
Front View
Uniformly loosen and remove the 8 bolts in several steps and in the sequence shown in the illustration.
Uniformly loosen and remove the 12 bolts in several steps in the sequence shown in the illustration.
NOTICE:
Uniformly loosen the bolts while keeping the camshaft and No. 2 camshaft level.
Remove the 5 camshaft bearing caps from the camshaft housing sub-assembly RH.
Remove the camshaft and No. 2 camshaft from the camshaft housing sub-assembly RH.
44.
REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH
Using a screwdriver with its tip wrapped in protective tape, remove the camshaft housing sub-assembly RH by prying between the cylinder head sub-assembly and camshaft housing sub-assembly RH.
Text in Illustration
*a
Protective Tape
*b
Pry
NOTICE:
Be careful not to damage the contact surfaces of the cylinder head sub-assembly and camshaft housing sub-assembly RH.
45.
REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 2)
While pushing the plunger, insert a pin of 1.0 mm (0.0394 in.) diameter into the plunger hole to hold the No. 3 chain tensioner assembly.
Text in Illustration
*1
Plunger
*a
Pin of 1.0 mm (0.0394 in.) diameter
*b
Push
Using SST to hold the hexagonal portion of each camshaft, loosen the bolts of the camshaft timing gear assembly and camshaft timing exhaust gear assembly LH.
Text in Illustration
*a
Turn
*b
Hold
SST
09922-10010
NOTICE:
Do not loosen the other 4 bolts. If any of the 4 bolts is loosened, replace the camshaft timing gear assembly and/or camshaft timing exhaust gear assembly LH with a new one.
Remove the 2 bolts from the No. 3 camshaft sub-assembly and No. 4 camshaft sub-assembly
Remove the camshaft timing gear assembly and camshaft timing exhaust gear assembly LH together with the No. 2 chain sub-assembly from the No. 3 camshaft sub-assembly and No. 4 camshaft sub-assembly.
46.
REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY
Remove the bolt and No. 3 chain tensioner assembly from the camshaft housing sub-assembly LH.
47.
REMOVE CAMSHAFT BEARING CAP (for Bank 2)
Check that the camshafts are positioned as shown in the illustration.
Text in Illustration
*1
Knock Pin
*a
Front View
Uniformly loosen and remove the 8 bolts in several steps and in the sequence shown in the illustration.
Uniformly loosen and remove the 13 bolts in several steps and in the sequence shown in the illustration.
NOTICE:
Uniformly loosen the bolts while keeping the No. 3 camshaft sub-assembly and No. 4 camshaft sub-assembly level.
Remove the 5 camshaft bearing caps from the camshaft housing sub-assembly LH.
Remove the No. 3 camshaft sub-assembly and No. 4 camshaft sub-assembly from the camshaft housing sub-assembly LH.
48.
REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH
Using a screwdriver with its tip wrapped in protective tape, remove the camshaft housing sub-assembly LH by prying between the cylinder head LH and camshaft housing sub-assembly LH.
Text in Illustration
*a
Protective Tape
*b
Pry
NOTICE:
Be careful not to damage the contact surfaces of the cylinder head LH and camshaft housing sub-assembly LH.
49.
REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
Remove the 24 No. 1 valve rocker arm sub-assemblies from the cylinder head sub-assembly and cylinder head LH.
HINT:
Arrange the removed parts in the correct order.
50.
REMOVE VALVE LASH ADJUSTER ASSEMBLY
Remove the 24 valve lash adjuster assemblies from the cylinder head sub-assembly and cylinder head LH.
HINT:
Arrange the removed parts in the correct order.
51.
REMOVE VALVE STEM CAP
Remove the 24 valve stem caps from the cylinder head sub-assembly and cylinder head LH.
HINT:
Arrange the removed parts in the correct order.
52.
REMOVE CYLINDER HEAD SUB-ASSEMBLY
Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 cylinder head bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.
NOTICE:
Be careful not to drop washers into the cylinder head sub-assembly.
Cylinder head warpage or cracking could result from removing bolts in an incorrect order.
HINT:
Arrange the removed parts in the correct order.
Remove the cylinder head sub-assembly.
53.
REMOVE CYLINDER HEAD GASKET
54.
REMOVE CYLINDER HEAD LH
Uniformly loosen and remove the 2 cylinder head set bolts in several steps and in the sequence shown in the illustration.
Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.
NOTICE:
Be careful not to drop washers into the cylinder head sub-assembly.
Cylinder head warpage or cracking could result from removing bolts in an incorrect order.
HINT:
Be sure to keep the removed parts for each installation position separate.
Remove the cylinder head LH.
55.
REMOVE NO. 2 CYLINDER HEAD GASKET
56.
REMOVE NO. 1 WATER OUTLET PIPE
Disconnect the 4 wire harness clamps.
Remove the 2 nuts, bolt and No. 1 water outlet pipe.
57.
REMOVE KNOCK SENSOR
Disconnect the 2 sensor connectors.
Remove the 2 bolts and 2 sensors.
58.
REMOVE CYLINDER BLOCK WATER JACKET SPACER
Remove the 2 cylinder block water jacket spacers from the cylinder block sub-assembly.
NOTICE:
Be sure to remove the cylinder block water jacket spacers. If not, they may fall and become damaged when the cylinder block sub-assembly is inverted.
59.
REMOVE TAPER SCREW PLUG
HINT:
It is not necessary to remove the taper screw plug unless it is being replaced.
Remove the taper screw plug from the cylinder block sub-assembly.
60.
REMOVE STRAIGHT PIN
HINT:
It is not necessary to remove the straight pin unless it is being replaced.
Remove the 6 straight pins from the camshaft housing sub-assembly LH and camshaft housing sub-assembly RH.
61.
REMOVE RING PIN
HINT:
It is not necessary to remove the ring pin unless it is being replaced.
Remove the 20 ring pins from the camshaft housing sub-assembly LH and camshaft housing sub-assembly RH.
62.
REMOVE STUD BOLT
HINT:
It is not necessary to remove the stud bolt unless it is being replaced.
Using an E6 "TORX" socket wrench, remove the 2 stud bolts from the cylinder head cover sub-assembly LH.
Using an E6 and E8 "TORX" socket wrench, remove the 6 stud bolts from the oil pan sub-assembly.