B1632/81 Lost Communication with Driver Side Rear Airbag Sensor
Diagnostic trouble codes · Vehicles built Nov 2010 – Jul 2012
Also covers:
- B1633/81 Driver Side Rear Airbag Sensor Initialization Incomplete
Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012
DESCRIPTION
The driver side - side airbag sensor and the driver side - rear airbag sensor consist of parts including the diagnostic circuit and the lateral deceleration sensor.When center airbag sensor assembly receives signals from the lateral deceleration sensor, it determines whether or not the SRS should be activated.
DTC B1632/81 and B1633/81 are set when a malfunction is detected in the driver side - side airbag sensor or driver side - rear airbag sensor circuit.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B1632/81 B1633/81 |
|
|
WIRING DIAGRAM




INSPECTION PROCEDURE
| 1. CHECK CONNECTORS (DRIVER SIDE - SIDE AIRBAG SENSOR - DRIVER SIDE - REAR AIRBAG SENSOR) |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the driver side floor wire connectors from the driver side - side airbag sensor and the driver side - rear airbag sensor.
Check the driver side floor wire connectors and terminals (on the driver side - side airbag sensor and the driver side - rear airbag sensor sides) and check that the connectors are properly connected.
Result Result
Proceed to
No problem.
A
Connectors or terminals incorrect.
B
Connectors connected improperly.
C
|
|
||||
|
|
||||
| A | |
| 2. CHECK DRIVER SIDE - SIDE AIRBAG SENSOR |
Connect the connector to the center airbag sensor assembly.
Interchange the driver side - side airbag sensor with the front passenger side - side airbag sensor and connect the connectors to them.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
Text in Illustration *a
Front Passenger Side - Side Airbag Sensor
*b
Center Airbag Sensor Assembly
*c
DLC3
*d
DTC 81
*e
DTC 82
Result Result
Proceed to
DTC B1632/81 or B1633/81 is output.
A
DTC B1637/82 or B1638/82 is output.
B
DTCs B1632/81, B1633/81, B1637/82 and B1638/82 are not output.
C
- HINT:
- DTCs other than DTC B1632/81, B1633/81, B1637/82 and B1638/82 may be output at this time, but they are not related to this check.
|
|
||||
|
|
||||
| A | |
| 3. CHECK DRIVER SIDE FLOOR WIRE (DRIVER SIDE - SIDE AIRBAG SENSOR - DRIVER SIDE - REAR AIRBAG SENSOR) |
Turn the ignition switch off.

Text in Illustration *A
for LHD
*B
for RHD
*a
Driver Side - Rear Airbag Sensor
*b
Driver Side - Side Airbag Sensor
*c
Driver Side Floor Wire
*d
Front view of wire harness connector
(to Driver Side - Rear Airbag Sensor)
*e
Front view of wire harness connector
(to Driver Side - Side Airbag Sensor)
*f
Connector C
*g
Connector B
*h
Service Wire
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check for open in the circuit.
Using a service wire, connect 1 and 2 of connector C.
- NOTICE:
- Do not forcibly insert the service wire into the terminals of the connector when connecting.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
L4-1 (BCL+) - L4-2 (BCL-)
Always
Below 1 Ω
- for RHD:
Tester Connection
Condition
Specified Condition
K2-1 (BCR+) - K2-2 (BCR-)
Always
Below 1 Ω
Check for short in the circuit.

Disconnect the service wire from connector C.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
L4-1 (BCL+) - L4-2 (BCL-)
Always
1 MΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
K2-1 (BCR+) - K2-2 (BCR-)
Always
1 MΩ or higher
Check for short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
L4-1 (BCL+) - Body ground
Always
1 MΩ or higher
L4-2 (BCL-) - Body ground
Always
1 MΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
K2-1 (BCR+) - Body ground
Always
1 MΩ or higher
K2-2 (BCR-) - Body ground
Always
1 MΩ or higher
Check for short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
- for LHD:
Tester Connection
Switch Condition
Specified Condition
L4-1 (BCL+) - Body ground
Ignition switch on
Below 1 V
L4-2 (BCL-) - Body ground
Ignition switch on
Below 1 V
- for RHD:
Tester Connection
Switch Condition
Specified Condition
K2-1 (BCR+) - Body ground
Ignition switch on
Below 1 V
K2-2 (BCR-) - Body ground
Ignition switch on
Below 1 V
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Text in Illustration *A
for LHD
*B
for RHD
*a
Driver Side - Rear Airbag Sensor
*b
Driver Side - Side Airbag Sensor
*c
Driver Side Floor Wire
*d
Front view of wire harness connector
(to Driver Side - Side Airbag Sensor)
*e
Connector B
|
|
||||
| OK | |
| 4. CHECK DRIVER SIDE - REAR AIRBAG SENSOR |
Connect the connector to the driver side - side airbag sensor.
Interchange the driver side - rear airbag sensor with the front passenger side - rear airbag sensor and connect the connectors to them.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
Text in Illustration *a
Front Passenger Side - Rear Airbag Sensor
*b
Driver Side - Side Airbag Sensor
*c
DLC3
*d
DTC 81
*e
DTC 82
Result Result
Proceed to
DTC B1632/81, B1633/81, B1637/82 and B1638/82 are not output.
A
DTC B1632/81 or B1633/81 is output.
B
DTC B1637/82 or B1638/82 is output.
C
- HINT:
- DTCs other than DTC B1632/81, B1633/81, B1637/82 and B1638/82 may be output at this time, but they are not related to this check.
|
|
||||
|
|
||||
| A | ||
| ||
