2011-2016 FJ Cruiser · Service Manual RESTRAINTS

B1633/81 Rear Airbag Sensor Assembly RH Initialization Incomplete

Diagnostic trouble codes · Vehicles built from Aug 2012

DESCRIPTION

The side collision sensor RH circuit (to determine deployment of the front seat airbag assembly RH and curtain shield airbag assembly RH) is composed of the center airbag sensor assembly, side airbag sensor assembly RH and rear airbag sensor RH.
The side airbag sensor assembly RH and rear airbag sensor RH detect impacts to the vehicle and send signals to the center airbag sensor assembly to determine if the airbag should be deployed.
DTC B1633/81 is stored when a malfunction is detected for the side collision sensor RH circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1633/81
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side collision sensor RH circuit.
  2. Side airbag sensor assembly RH malfunction
  3. Rear airbag sensor RH malfunction
  4. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Side airbag sensor assembly RH
  3. Rear airbag sensor RH
  4. Center airbag sensor assembly

WIRING DIAGRAM

Refer to DTC B1623/81 (Click here).

INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).


1. CHECK HISTORY DTC
  1. Check for history DTCs (Click here).

    Result:
    Result
    Proceed to
    History DTC B1632/81 is not output.
    A
    History DTC B1632/81 is output.
    B

    HINT:
    Codes other than history DTC B1622/81 may be output at this time, but they are not related to this check.



B
GO TO DTC B1632/81 (Click here)
A


2. CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the side airbag sensor assembly RH and rear airbag sensor RH.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the side airbag sensor assembly RH and rear airbag sensor RH.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


3. CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

  1. C267556E01
    Connect the connector to the rear airbag sensor RH.

  1. Interchange the side airbag sensor assembly RH with LH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1633/81 is output.
    A
    DTC B1638/82 is output.
    B
    DTCs B1633/81 and B1638/82 are not output.
    C

    HINT:
    Codes other than DTCs B1633/81 and B1638/82 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Center Airbag Sensor Assembly



B
REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


4. CHECK FLOOR WIRE (OPEN)

  1. C268577E06
    Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K2-1 (BCR+) - K2-2 (BCR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector C.

    Text in Illustration 
    *1
    Rear Airbag Sensor RH
    *2
    Side Airbag Sensor Assembly RH
    *3
    Floor Wire
    *4
    Service Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)
    *b
    Front view of wire harness connector
    (to Rear Airbag Sensor RH)



NG
REPLACE FLOOR WIRE
OK


5. CHECK FLOOR WIRE (SHORT TO GROUND)

  1. C268578E05
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K2-1 (BCR+) - Body ground
    Always
    1 MΩ or higher
    K2-2 (BCR-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Rear Airbag Sensor RH
    *2
    Side Airbag Sensor Assembly RH
    *3
    Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE FLOOR WIRE
OK


6. CHECK FLOOR WIRE (SHORT)

  1. C268578E05
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K2-1 (BCR+) - K2-2 (BCR-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Rear Airbag Sensor RH
    *2
    Side Airbag Sensor Assembly RH
    *3
    Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE FLOOR WIRE
OK


7. CHECK FLOOR WIRE (SHORT TO B+)

  1. C268578E05
    Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    K2-1 (BCR+) - Body ground
    Ignition switch ON
    Below 1 V
    K2-2 (BCR-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Rear Airbag Sensor RH
    *2
    Side Airbag Sensor Assembly RH
    *3
    Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE FLOOR WIRE
OK


8. CHECK REAR AIRBAG SENSOR RH

  1. C268576E01
    Interchange the rear airbag sensor RH with LH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTCs B1633/81 and B1638/82 are not output.
    A
    DTC B1633/81 is output.
    B
    DTC B1638/82 is output.
    C

    HINT:
    Codes other than DTCs B1633/81 and B1638/82 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the rear airbag sensor RH and LH to their original positions and connect the connectors.

    Text in Illustration 
    *1
    Rear Airbag Sensor LH
    *2
    Side Airbag Sensor Assembly RH



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE REAR AIRBAG SENSOR RH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)


← B1632/81 Lost Communication with Driver Side Rear Airbag Sensor (+ B1633/81) (Nov 2010 – Jul 2012)B1635/24 Rear Airbag Sensor LH Circuit Malfunction (from Aug 2012) →