B1642/81 Lost Communication with Driver Side Satellite Sensor Bus
Diagnostic trouble codes · Vehicles built Jul 2007 – Oct 2010
Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012
DESCRIPTION
The side airbag sensor LH and the rear airbag sensor LH consist of parts including the diagnostic circuit and the lateral deceleration sensor.When the center airbag sensor assembly receives signals from the lateral deceleration sensor, it determines whether or not the SRS should be activated.
DTC B1642/81 is set when a malfunction is detected in the side airbag sensor LH or rear airbag sensor LH circuit.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B1642/81 |
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.
- Turn the ignition switch off.
- Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
- Disconnect the connector from the center airbag sensor assembly.
- Disconnect the connectors from the steering pad.
- Disconnect the connectors from the front passenger airbag assembly.
- Disconnect the connector from the front seat outer belt assembly LH.
- Disconnect the connector from the front seat outer belt assembly RH.
- HINT:
- Skip the following steps if side airbags and curtain shield airbags are not fitted.
- Disconnect the connector from the front seat side airbag assembly LH.
- Disconnect the connector from the front seat side airbag assembly RH.
- Disconnect the connector from the curtain shield airbag assembly LH.
- Disconnect the connector from the curtain shield airbag assembly RH.
| 1. CHECK CONNECTORS (CENTER AIRBAG SENSOR ASSEMBLY - SIDE AIRBAG SENSOR LH) |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the floor wire No.2 connectors from the center airbag sensor assembly and the side airbag sensor LH.
Check the floor wire No.2 connectors and terminals (on the center airbag sensor assembly and the side airbag sensor LH sides) and check that the connectors are properly connected.
- Result:
Result
Proceed to
No problem.
A
Connectors or terminals incorrect.
B
Connector connected improperly.
C
|
|
||||
|
|
||||
| A | |
| 2. CHECK FLOOR WIRE NO.2 (CENTER AIRBAG SENSOR ASSEMBLY - SIDE AIRBAG SENSOR LH) |
Check for open in the circuit.

Using a service wire, connect L4-4 (BBL+) and L4-3 (BBL-) of connector C.
- NOTICE:
- Do not forcibly insert the service wire into the terminals of the connector when connecting.
Measure the resistance.
- Standard resistance:
Tester Connection
Condition
Specified Condition
L1-8 (BBD+) - L1-15 (BBD-)
Always
Below 1Ω
Check for short in the circuit.

Disconnect the service wire from connector C.
Measure the resistance.
- Standard resistance:
Tester Connection
Condition
Specified Condition
L1-8 (BBD+) - L1-15 (BBD-)
Always
1 MΩ or higher
Check for short to ground in the circuit.
Measure the resistance.
- Standard resistance:
Tester Connection
Condition
Specified Condition
L1-8 (BBD+) - Body ground
Always
1 MΩ or higher
L1-15 (BBD-) - Body ground
Always
1 MΩ or higher
Check for short to B+ in the circuit.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the on position.
Measure the voltage.
- Standard voltage:
Tester Connection
Switch Condition
Specified Condition
L1-8 (BBD+) - Body ground
Ignition switch on
Below 1 V
L1-15 (BBD-) - Body ground
Ignition switch on
Below 1 V
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
|
|
||||
| OK | |
| 3. CHECK SIDE AIRBAG SENSOR LH |
Connect the connector to the center airbag sensor assembly.
Interchange the side airbag sensor LH with the side airbag sensor RH and connect the connectors to them.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the on position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the lock position.
Turn the ignition switch to the on position, and wait for at least 60 seconds.
Check for DTCs (Click here).
- Result:
Result
Proceed to
DTC B1642/81 is output.
A
DTC B1647/82 is output.
B
DTC B1642/81 or B1647/82 is not output.
C
- HINT:
- DTCs other than DTC B1642/81 and B1647/82 may be output at this time, but they are not related to this check.
|
|
||||
|
|
||||
| A | |
| 4. CHECK CONNECTORS (SIDE AIRBAG SENSOR LH - REAR AIRBAG SENSOR LH) |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the floor wire No.2 connectors from the side airbag sensor LH and the rear airbag sensor LH.
Check the floor wire No.2 connectors and terminals (on the side airbag sensor LH and the rear airbag sensor LH sides) and check that the connectors are properly connected.
- Result:
Result
Proceed to
No problem.
A
Connectors or terminals incorrect.
B
Connector connected improperly.
C
|
|
||||
|
|
||||
| A | |
| 5. CHECK FLOOR WIRE NO.2 (SIDE AIRBAG SENSOR LH - REAR AIRBAG SENSOR LH) |
Check for open in the circuit.

Using a service wire, connect L5-1 (BCL-) and L5-2 (BCL+) of connector C.
- NOTICE:
- Do not forcibly insert the service wire into the terminals of the connector when connecting.
Measure the resistance.
- Standard resistance:
Tester Connection
Condition
Specified Condition
L4-1 (BCL+) - L4-2 (BCL-)
Always
Below 1Ω
Check for short in the circuit.

Disconnect the service wire from connector C.
Measure the resistance.
- Standard resistance:
Tester Connection
Condition
Specified Condition
L4-1 (BCL+) - L4-2 (BCL-)
Always
1 MΩ or higher
Check for short to ground in the circuit.
Measure the resistance.
- Standard resistance:
Tester Connection
Condition
Specified Condition
L4-1 (BCL+) - Body ground
Always
1 MΩ or higher
L4-2 (BCL-) - Body ground
Always
1 MΩ or higher
Check for short to B+ in the circuit.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the on position.
Measure the voltage.
- Standard voltage:
Tester Connection
Switch Condition
Specified Condition
L4-1 (BCL+) - Body ground
Ignition switch on
Below 1 V
L4-2 (BCL-) - Body ground
Ignition switch on
Below 1 V
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
|
|
||||
| OK | |
| 6. CHECK REAR AIRBAG SENSOR LH |
Connect the connector to the side airbag sensor LH.
Interchange the rear airbag sensor LH with the rear airbag sensor RH and connect the connectors to them.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the on position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the lock position.
Turn the ignition switch to the on position, and wait for at least 60 seconds.
Check for DTCs (Click here).
- Result:
Result
Proceed to
DTC B1642/81 or B1647/82 is not output.
A
DTC B1642/81 is output.
B
DTC B1647/82 is output.
C
- HINT:
- DTCs other than DTC B1642/81 and B1647/82 may be output at this time, but they are not related to this check.
|
|
||||
|
|
||||
| A | ||
| ||
