2011-2016 FJ Cruiser · Service Manual RESTRAINTS

B1642/81 Lost Communication with Driver Side Satellite Sensor Bus

Diagnostic trouble codes · Vehicles built Nov 2010 – Jul 2012

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2012

DESCRIPTION

The driver side - side airbag sensor and the driver side - rear airbag sensor consist of parts including the diagnostic circuit and the lateral deceleration sensor.
When the center airbag sensor assembly receives signals from the lateral deceleration sensor, it determines whether or not the SRS should be activated.
DTC B1642/81 is set when a malfunction is detected in the driver side - side airbag sensor or driver side - rear airbag sensor circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1642/81
  1. Center airbag sensor assembly detects open circuit signal in driver side - side airbag sensor circuit or driver side - rear airbag sensor circuit for 2 seconds.
  2. Driver side - side airbag sensor malfunction
  3. Driver side - rear airbag sensor malfunction
  4. Center airbag sensor assembly malfunction
  1. Driver side floor wire
  2. Driver side - side airbag sensor
  3. Driver side - rear airbag sensor
  4. Center airbag sensor assembly

WIRING DIAGRAM

C148422E42
C148422E46

INSPECTION PROCEDURE


1. CHECK CONNECTORS (CENTER AIRBAG SENSOR ASSEMBLY - DRIVER SIDE - SIDE AIRBAG SENSOR)
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the driver side floor wire connectors from the center airbag sensor assembly and the driver side - side airbag sensor.

  1. Check the driver side floor wire connectors and terminals (on the center airbag sensor assembly and the driver side - side airbag sensor sides) and check that the connectors are properly connected.

    Result 
    Result
    Proceed to
    No problem.
    A
    Connectors or terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPLACE DRIVER SIDE FLOOR WIRE

C
CONNECT CONNECTORS PROPERLY
A


2. CHECK DRIVER SIDE FLOOR WIRE (CENTER AIRBAG SENSOR ASSEMBLY - DRIVER SIDE - SIDE AIRBAG SENSOR)

  1. H100908E06
    Check for open in the circuit.
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Driver Side - Side Airbag Sensor
    *b
    Center Airbag Sensor Assembly
    *c
    Driver Side Floor Wire
    *d
    Front view of wire harness connector
    (to Driver Side - Side Airbag Sensor)
    *e
    Rear view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *f
    Connector C
    *g
    Connector B
    *h
    Service Wire
    1. Using a service wire, connect 4 and 3 of connector C.

      NOTICE:
      Do not forcibly insert the service wire into the terminals of the connector when connecting.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD:
      Tester Connection
      Condition
      Specified Condition
      L1-8 (BBD+) - L1-15 (BBD-)
      Always
      Below 1 Ω
      for RHD:
      Tester Connection
      Condition
      Specified Condition
      K11-8 (BBD+) - K11-15 (BBD-)
      Always
      Below 1 Ω

  1. H100839E20
    Check for short in the circuit.
    1. Disconnect the service wire from connector C.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD:
      Tester Connection
      Condition
      Specified Condition
      L1-8 (BBD+) - L1-15 (BBD-)
      Always
      1 MΩ or higher
      for RHD:
      Tester Connection
      Condition
      Specified Condition
      K11-8 (BBD+) - K11-15 (BBD-)
      Always
      1 MΩ or higher

  1. Check for short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD:
      Tester Connection
      Condition
      Specified Condition
      L1-8 (BBD+) - Body ground
      Always
      1 MΩ or higher
      L1-15 (BBD-) - Body ground
      Always
      1 MΩ or higher
      for RHD:
      Tester Connection
      Condition
      Specified Condition
      K11-8 (BBD+) - Body ground
      Always
      1 MΩ or higher
      K11-15 (BBD-) - Body ground
      Always
      1 MΩ or higher

  1. Check for short to B+ in the circuit.

    1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      for RHD:
      Tester Connection
      Switch Condition
      Specified Condition
      L1-8 (BBD+) - Body ground
      Ignition switch ON
      Below 1 V
      L1-15 (BBD-) - Body ground
      Ignition switch ON
      Below 1 V
      for LHD:
      Tester Connection
      Switch Condition
      Specified Condition
      K11-8 (BBD+) - Body ground
      Ignition switch ON
      Below 1 V
      K11-15 (BBD-) - Body ground
      Ignition switch ON
      Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

      Text in Illustration 
      *A
      for LHD
      *B
      for RHD
      *a
      Driver Side - Side Airbag Sensor
      *b
      Center Airbag Sensor Assembly
      *c
      Driver Side Floor Wire
      *d
      Rear view of wire harness connector
      (to Center Airbag Sensor Assembly)
      *e
      Connector B



NG
REPLACE DRIVER SIDE FLOOR WIRE
OK


3. CHECK DRIVER SIDE - SIDE AIRBAG SENSOR
  1. Connect the connector to the center airbag sensor assembly.

  1. C135739E02
    Interchange the driver side - side airbag sensor with the front passenger side - side airbag sensor and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Text in Illustration 
    *a
    Front Passenger Side - Side Airbag Sensor
    *b
    Center Airbag Sensor Assembly
    *c
    DLC3
    *d
    DTC 81
    *e
    DTC 82
    Result 
    Result
    Proceed to
    DTC B1642/81 is output.
    A
    DTC B1647/82 is output.
    B
    DTC B1642/81 or B1647/82 is not output.
    C

    HINT:
    DTCs other than DTC B1642/81 and B1647/82 may be output at this time, but they are not related to this check.



B
REPLACE DRIVER SIDE - SIDE AIRBAG SENSOR (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


4. CHECK CONNECTORS (DRIVER SIDE - SIDE AIRBAG SENSOR - DRIVER SIDE - REAR AIRBAG SENSOR)
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the driver side floor wire connectors from the driver side - side airbag sensor and the driver side - rear airbag sensor.

  1. Check the driver side floor wire connectors and terminals (on the driver side - side airbag sensor and the driver side - rear airbag sensor sides) and check that the connectors are properly connected.

    Result 
    Result
    Proceed to
    No problem.
    A
    Connectors or terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPLACE DRIVER SIDE FLOOR WIRE

C
CONNECT CONNECTORS PROPERLY
A


5. CHECK DRIVER SIDE FLOOR WIRE (DRIVER SIDE - SIDE AIRBAG SENSOR - DRIVER SIDE - REAR AIRBAG SENSOR)

  1. H100841E13
    Check for open in the circuit.
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Driver Side - Rear Airbag Sensor
    *b
    Driver Side - Side Airbag Sensor
    *c
    Driver Side Floor Wire
    *d
    Front view of wire harness connector
    (to Driver Side - Rear Airbag Sensor)
    *e
    Front view of wire harness connector
    (to Driver Side - Side Airbag Sensor)
    *f
    Connector C
    *g
    Connector B
    *h
    Service Wire
    1. Using a service wire, connect 1 and 2 of connector C.

      NOTICE:
      Do not forcibly insert the service wire into the terminals of the connector when connecting.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD:
      Tester Connection
      Condition
      Specified Condition
      L4-1 (BCL+) - L4-2 (BCL-)
      Always
      Below 1 Ω
      for RHD:
      Tester Connection
      Condition
      Specified Condition
      K2-1 (BCR+) - K2-2 (BCR-)
      Always
      Below 1 Ω

  1. H100842E16
    Check for short in the circuit.
    1. Disconnect the service wire from connector C.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD:
      Tester Connection
      Condition
      Specified Condition
      L4-1 (BCL+) - L4-2 (BCL-)
      Always
      1 MΩ or higher
      for RHD:
      Tester Connection
      Condition
      Specified Condition
      K2-1 (BCR+) - K2-2 (BCR-)
      Always
      1 MΩ or higher

  1. Check for short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for LHD:
      Tester Connection
      Condition
      Specified Condition
      L4-1 (BCL+) - Body ground
      Always
      1 MΩ or higher
      L4-2 (BCL-) - Body ground
      Always
      1 MΩ or higher
      for RHD:
      Tester Connection
      Condition
      Specified Condition
      K2-1 (BCR+) - Body ground
      Always
      1 MΩ or higher
      K2-2 (BCR-) - Body ground
      Always
      1 MΩ or higher

  1. Check for short to B+ in the circuit.

    1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      for LHD:
      Tester Connection
      Switch Condition
      Specified Condition
      L4-1 (BCL+) - Body ground
      Ignition switch ON
      Below 1 V
      L4-2 (BCL-) - Body ground
      Ignition switch ON
      Below 1 V
      for RHD:
      Tester Connection
      Switch Condition
      Specified Condition
      K2-1 (BCR+) - Body ground
      Ignition switch ON
      Below 1 V
      K2-2 (BCR-) - Body ground
      Ignition switch ON
      Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

      Text in Illustration 
      *A
      for LHD
      *B
      for RHD
      *a
      Driver Side - Rear Airbag Sensor
      *b
      Driver Side - Side Airbag Sensor
      *c
      Driver Side Floor Wire
      *d
      Front view of wire harness connector
      (to Driver Side - Side Airbag Sensor)
      *e
      Connector B



NG
REPLACE DRIVER SIDE FLOOR WIRE
OK


6. CHECK DRIVER SIDE - REAR AIRBAG SENSOR
  1. Connect the connector to the driver side - side airbag sensor.

  1. C135743E03
    Interchange the driver side - rear airbag sensor with the front passenger side - rear airbag sensor and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Text in Illustration 
    *a
    Front Passenger Side - Rear Airbag Sensor
    *b
    Driver Side - Side Airbag Sensor
    *c
    DLC3
    *d
    DTC 81
    *e
    DTC 82
    Result 
    Result
    Proceed to
    DTC B1642/81 or B1647/82 is not output.
    A
    DTC B1642/81 is output.
    B
    DTC B1647/82 is output.
    C

    HINT:
    DTCs other than DTC B1642/81 and B1647/82 may be output at this time, but they are not related to this check.



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE DRIVER SIDE - REAR AIRBAG SENSOR (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)


← B1642/81 Lost Communication with Driver Side Satellite Sensor Bus (Jul 2007 – Oct 2010)B1642/81 Lost Communication with Side Satellite Sensor Bus RH (from Aug 2012) →