2011-2016 FJ Cruiser · Service Manual COMMUNICATION SYSTEM

Open in CAN Main Bus Line (RHD Models)

Circuit diagnosis · Vehicles built from Nov 2010

DESCRIPTION

There may be an open circuit in the CAN main wire and/or DLC3 branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.
Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is 70 Ω or higher.
  1. CAN main wire and connector
  2. CAN junction connector No. 1
  3. CAN junction connector No. 2
  4. CAN junction connector No. 3
  5. ECM
  6. Combination meter assembly (combination meter ECU)
  7. DLC3 branch wire or connector

WIRING DIAGRAM

E214896E01

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.
  2. Turn the ignition switch off before inspecting CAN bus wires for a ground short.
  3. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not operating.
  4. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
  1. Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK DLC3

  1. E214901E01
    Disconnect the E91 CAN junction connector No. 2 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E1-6 (CANH) - E91-6 (CANH)
    Ignition switch off
    Below 1 Ω
    E1-14 (CANL) - E91-12 (CANL)
    Ignition switch off
    Below 1 Ω

    Text in Illustration 
    *a
    DLC3
    *b
    Front view of wire harness connector
    (to CAN Junction Connector No. 2)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CAN-H, CAN-L)
OK


3. CHECK FOR OPEN IN CAN BUS MAIN WIRE (CAN JUNCTION CONNECTOR NO. 1 - ECM)

  1. E214897E07
    Disconnect the E95 CAN junction connector No. 1 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E95-1 (CANH) - E95-12 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN Junction Connector No. 1)



NG
Go to step 5
OK


4. CHECK FOR OPEN IN CAN BUS MAIN WIRE (CAN JUNCTION CONNECTOR NO. 1 - COMBINATION METER ASSEMBLY (COMBINATION METER ECU))

  1. E214897E08
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E95-3 (CANH) - E95-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN Junction Connector No. 1)



NG
Go to step 7
OK

REPLACE CAN JUNCTION CONNECTOR NO. 1

5. CONNECT CONNECTOR
  1. Reconnect the E95 CAN junction connector No. 1 connector.


NEXT


6. CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM - CAN JUNCTION CONNECTOR NO. 1)

  1. E214877E04
    Disconnect the E81 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E81-32 (CANH) - E81-31 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE ECM (Click here)

7. CONNECT CONNECTOR
  1. Reconnect the E95 CAN junction connector No. 1 connector.


NEXT


8. CHECK FOR OPEN IN CAN BUS MAIN WIRE (CAN JUNCTION CONNECTOR NO. 2 - COMBINATION METER ASSEMBLY (COMBINATION METER ECU))

  1. E214898E01
    Disconnect the E92 CAN junction connector No. 2 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E92-1 (CANH) - E92-7 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN Junction Connector No. 2)



NG
Go to step 10
OK


9. CHECK FOR OPEN IN CAN BUS MAIN WIRE (CAN JUNCTION CONNECTOR NO. 2 - CAN JUNCTION CONNECTOR NO. 1)

  1. E214898E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E92-2 (CANH) - E92-8 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN Junction Connector No. 2)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE CAN JUNCTION CONNECTOR NO. 2

10. CONNECT CONNECTOR
  1. Reconnect the E92 CAN junction connector No. 2 connector.


NEXT


11. CHECK FOR OPEN IN CAN BUS MAIN WIRE (CAN JUNCTION CONNECTOR NO. 3 - COMBINATION METER ASSEMBLY (COMBINATION METER ECU))

  1. E214897E10
    Disconnect the A43 CAN junction connector No. 3 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A43-2 (CANH) - A43-13 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN Junction Connector No. 3)



NG
Go to step 13
OK


12. CHECK FOR OPEN IN CAN BUS MAIN WIRE (CAN JUNCTION CONNECTOR NO. 3 - CAN JUNCTION CONNECTOR NO. 2)

  1. E214897E11
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A43-3 (CANH) - A43-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN Junction Connector No. 3)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE CAN JUNCTION CONNECTOR NO. 3

13. CONNECT CONNECTOR
  1. Reconnect the A43 CAN junction connector No. 3 connector.


NEXT


14. CHECK FOR OPEN IN CAN BUS MAIN WIRE (CAN JUNCTION CONNECTOR NO. 3 - COMBINATION METER ASSEMBLY (COMBINATION METER ECU))

  1. E214880E01
    Disconnect the E14 combination meter assembly (combination meter ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E14-10 (CANH) - E14-9 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter Assembly (Combination Meter ECU))



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE COMBINATION METER ASSEMBLY (COMBINATION METER ECU) (Click here)


← Open in CAN Main Bus Line (LHD Models) (from Nov 2010)Short in CAN Bus Lines (Jul 2007 – Jul 2009) →