Open in CAN Main Bus Line (LHD Models)
Circuit diagnosis · Vehicles built from Nov 2010
DESCRIPTION
There may be an open circuit in the CAN main wire and/or DLC3 branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.| Symptom |
Trouble Area |
| Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is 70 Ω or higher. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.
- Turn the ignition switch off before inspecting CAN bus wires for a ground short.
- After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not operating.
- Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.
- Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.
- HINT:
- Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
- Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
- Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
| NEXT | |
| 2. CHECK DLC3 |
Disconnect the E95 CAN junction connector No. 1 connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E1-6 (CANH) - E95-4 (CANH)
Ignition switch off
Below 1 Ω
E1-14 (CANL) - E95-15 (CANL)
Ignition switch off
Below 1 Ω
Text in Illustration *a
Front view of wire harness connector
(to CAN Junction Connector No. 1)
*b
DLC3
|
|
||||
| OK | |
| 3. CHECK FOR OPEN IN CAN BUS MAIN WIRE (CAN JUNCTION CONNECTOR NO. 1 - ECM) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E95-1 (CANH) - E95-12 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Front view of wire harness connector
(to CAN Junction Connector No. 1)
|
|
||||
| OK | |
| 4. CHECK FOR OPEN IN CAN BUS MAIN WIRE (CAN JUNCTION CONNECTOR NO. 1 - COMBINATION METER ASSEMBLY (COMBINATION METER ECU)) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E95-3 (CANH) - E95-14 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Front view of wire harness connector
(to CAN Junction Connector No. 1)
|
|
||||
| OK | ||
| ||
| 5. CONNECT CONNECTOR |
Reconnect the E95 CAN junction connector No. 1 connector.
| NEXT | |
| 6. CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM - CAN JUNCTION CONNECTOR NO. 1) |
Disconnect the E81 ECM connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E81-32 (CANH) - E81-31 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Front view of wire harness connector
(to ECM)
|
|
||||
| OK | ||
| ||
| 7. CONNECT CONNECTOR |
Reconnect the E95 CAN junction connector No. 1 connector.
| NEXT | |
| 8. CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER ASSEMBLY (COMBINATION METER ECU) - CAN JUNCTION CONNECTOR NO. 1) |
Disconnect the E14 combination meter assembly (combination meter ECU) connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E14-10 (CANH) - E14-9 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Front view of wire harness connector
(to Combination Meter Assembly (Combination Meter ECU))
|
|
||||
| OK | ||
| ||
