C1407 Open or Short in Rear Speed Sensor RH Circuit
Diagnostic trouble codes · Vehicles built Nov 2010 – Jul 2012
Also covers:
- C1408 Open or Short in Rear Speed Sensor LH Circuit
Versions by build date: Nov 2010 – Jul 2012 from Aug 2012
DESCRIPTION
Refer to DTCs C1401 and C1402 (Click here).| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1407 C1408 |
Either condition is met:
|
|
- HINT:
- DTC C1407 is for the rear speed sensor RH.
- DTC C1408 is for the rear speed sensor LH.
- DTC C1407 is for the rear speed sensor RH.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When replacing the master cylinder solenoid, perform calibration (Click here).
- Check the speed sensor signal after replacement (Click here).
- When replacing the master cylinder solenoid, perform calibration (Click here).
| 1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION) |
Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
RR Speed Open
Rear speed sensor RH open detection/ Error or Normal
Normal
-
RL Speed Open
Rear speed sensor LH open detection/ Error or Normal
Normal
-
- OK:
- Normal (there are no momentary interruptions).
- HINT:
- Perform the above inspection before removing the sensor and connector.
|
|
||||
| OK | |
| 2. READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
RR Wheel Speed
Rear speed sensor RH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
RL Wheel Speed
Rear speed sensor LH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
Check that there is no difference between the speed value output from the speed sensor displayed on the tester and the speed value displayed on the speedometer when driving the vehicle.
- HINT:
- Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click here).
- OK:
- The speed value output from the speed sensor displayed on the tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
|
|
||||
| OK | |
| 3. RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output (Click here).
Result Result
Proceed to
DTCs C1407 and C1408 are not output
A
DTCs C1407 and/or C1408 are output
B
|
|
||||
| A | ||
| ||
| 4. INSPECT SKID CONTROL SENSOR WIRE |


| *1 |
Skid Control Sensor Wire |
- |
- |
| *a |
for RH |
*b |
for LH |
Remove the skid control sensor wire.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for RH Tester Connection
Condition
Specified Condition
OX1-4 - X1-2 (RR+)
Always
Below 1 Ω
OX1-3 - X1-1 (RR-)
Always
Below 1 Ω
OX1-4 - OX1-3
Always
10 kΩ or higher
OX1-4 - OX1-1
Always
10 kΩ or higher
OX1-4 - OX1-2
Always
10 kΩ or higher
for LH Tester Connection
Condition
Specified Condition
OX1-2 - X2-2 (RL+)
Always
Below 1 Ω
OX1-1 - X2-1 (RL-)
Always
Below 1 Ω
OX1-2 - OX1-1
Always
10 kΩ or higher
OX1-2 - OX1-3
Always
10 kΩ or higher
OX1-2 - OX1-4
Always
10 kΩ or higher
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR) |
Install the skid control sensor wire.
Disconnect the A4 skid control ECU connector.
Disconnect the X1 and/or X2 rear speed sensor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for RH Tester Connection
Condition
Specified Condition
A4-5 (RR+) - X1-2 (RR+)
Always
Below 1 Ω
A4-5 (RR+) - Body ground
Always
10 kΩ or higher
A4-19 (RR-) - X1-1 (RR-)
Always
Below 1 Ω
A4-19 (RR-) - Body ground
Always
10 kΩ or higher
for LH Tester Connection
Condition
Specified Condition
A4-20 (RL+) - X2-2 (RL+)
Always
Below 1 Ω
A4-20 (RL+) - Body ground
Always
10 kΩ or higher
A4-6 (RL-) - X2-1 (RL-)
Always
Below 1 Ω
A4-6 (RL-) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. INSPECT SKID CONTROL ECU (RR+, RL+ TERMINAL) |
Disconnect the X1 and/or X2 rear speed sensor connector.
Connect the A4 skid control ECU connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
for RH Tester Connection
Switch Condition
Specified Condition
X1-2 (RR+) - Body ground
Ignition switch ON
11 to 14 V
for LH Tester Connection
Switch Condition
Specified Condition
X2-2 (RL+) - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Rear Speed Sensor)
*b
for RH
*c
for LH
|
|
||||
| OK | ||
| ||
