Home › ENGINE › 1GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0505    Idle Control System

for Preparation Click here


DESCRIPTION

The idling speed is controlled by the ETCS (Electronic Throttle Control System). The ETCS is comprised of: 1) the one valve type throttle with motor body assembly; 2) the throttle actuator, which operates the throttle valve; 3) the Throttle Position (TP) sensor, which detects the opening angle of the throttle valve; 4) the Accelerator Pedal Position (APP) sensor, which detects the accelerator pedal position; and 5) the ECM, which controls the ETCS. Based on the target idling speed, the ECM controls the throttle actuator to provide the proper throttle valve opening angle.

DTC No.
DTC Detection Condition
Trouble Area
P0505
Idling speed continues to vary greatly from target idling speed (2 trip detection logic)
  1. ETCS
  2. Intake system
  3. PCV valve and hose
  4. PCV hose connection
  5. ECM

MONITOR DESCRIPTION

The ECM monitors the idling speed and idling air flow volume to conduct Idle Speed Control (ISC). The ECM determines that the ISC system is malfunctioning if either of the following conditions is met:
  1. The difference between the target engine idling speed and actual engine idling speed exceeds the threshold and the IAC flow rate learned value is stuck at the upper or lower limit for 5 seconds or more.
  2. After driving at a vehicle speed of 10 km/h (6.25 mph) or more, the difference between the target and actual engine idling speed exceeds the threshold 5 times or more during a driving cycle, and then the system determines that the IAC flow rate learned value is stuck at the upper or lower limit, or that the IAC flow rate learned value has been changed by an amount that exceeds the threshold.

A121611E06


MONITOR STRATEGY


Related DTCs
P0505: ISC Function
Required Sensors/Components (Main)
ETCS
Required Sensors/Components (Related)
Crankshaft position sensor, Engine coolant temperature sensor, Vehicle speed sensor
Frequency of Operation
Continuous
Duration
10 minutes
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
P0010, P0020 (VVT oil control valve)
P0011, P0021 (VVT system - advance)
P0012, P0022 (VVT system - retard)
P0013, P0023 (Exhaust VVT oil control valve)
P0014, P0024 (Exhaust VVT system - advance)
P0015, P0025 (Exhaust VVT system - retard)
P0016, P0018 (VVT system - misalignment)
P0017, P0019 (Exhaust VVT system - misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater)
P0102, P0103 (Mass air flow meter)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120 - P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient engine coolant temperature for closed loop fuel control)
P014C - P014F, P015A - P015D, P2195 - P2198, P2237 - P2242, P2252, P2253, P2255, P2256 (Air fuel ratio sensor)
P0171, P0172, P0174, P0175 (Fuel system)
P0301 - P0306 (Misfire)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P0351 - P0356 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P0451 - P0453 (EVAP system)
P0500 (Vehicle speed sensor)
P0705 (Shift lever position switch)
P0748, P0778 (Pressure control solenoid)
P0973, P0974, P0976, P0977, P0985, P0986 (Shift solenoid)
P219A, P219B (Air-fuel ratio imbalance)
Engine
Running

TYPICAL MALFUNCTION THRESHOLDS


Either condition is met
1 or 2
1. Both of following conditions A and B met
-
A. Engine speed - Target engine speed
Less than -100 rpm, or more than 150 rpm (A/C off and NSW off)
Less than -100 rpm, or more than 200 rpm (A/C on or NSW on)
B. IAC flow rate learned value
1.03 L/sec. or less, or 7.5 L/sec. or more for 5 seconds or more
2. Both of following conditions C and D met
-
C. Frequency that both of following conditions (a) and (b) met
5 times or more
(a) Engine speed - Target engine speed
Less than -100 rpm, or more than 150 rpm (A/C off and NSW off)
Less than -100 rpm, or more than 200 rpm (A/C on or NSW on)
(b) Vehicle condition
Stopped after being driven at 10 km/h (6.25 mph) or more
D. Either condition is met
(c) or (d)
(c) IAC flow rate learned value
1.03 L/sec. or less, or 7.5 L/sec. or more
(d) Amount of change of IAC flow rate learned value
+1.9 L/sec. or more, or -3.55 L/sec. or less

CONFIRMATION DRIVING PATTERN


A231468E06

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and warm it up (until the engine coolant temperature is 75°C (167°F) or higher) with all the accessories switched off [B].
  7. Idle the engine for 5 minutes or more [C].

    HINT:
    In order to keep the idling stable, turn off the A/C and all other electric loads and do not perform any shift operations.

  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
  9. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0505.
  12. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [E] and [F].

  13. Accelerate the vehicle to 10 km/h (6.25 mph) or more, and then idle the engine for 20 seconds or more [E].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  14. Repeat step [E] 5 times.
  15. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [F].
  16. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  17. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  18. Input the DTC: P0505.
  19. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shown ABNORMAL, the system has a malfunction.

  20. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


INSPECTION PROCEDURE

HINT:
  1. The following conditions may also cause DTC P0505 to be stored:
    1. (1) The floor carpet overlapping slightly onto the accelerator pedal, causing the accelerator pedal to be slightly depressed and therefore the throttle valve position to be slightly open.
    2. (2) The accelerator pedal being not fully released.
  2. Read freeze frame data using the Techstream. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.
  3. Refer to "Data List / Active Test" [Engine Speed, ISC Feedback Value and ISC Learning Value] (Click here).

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0505)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P0505 is output
    A
    P0505 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0505 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK PCV HOSE CONNECTIONS
  1. Check the PCV hose connections (Click here).

    OK:
    PCV valve and hose are connected correctly and are not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


3.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leak (Click here).

    OK:
    No leak from intake system.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the intake system (Click here).



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


4.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (THROTTLE VALVE)
  1. Check the throttle with motor body assembly condition.

    OK:
    Throttle valve is not contaminated with foreign objects and moves smoothly.

    HINT:
    Perform "Inspection After Repair" after replacing the throttle with motor body assembly (Click here).



NG
REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY (Click here)
OK


5.CONFIRM WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Read DTCs.

Result 
Result
Proceed to
DTC P0505 is output
A
No DTC is output
B


B
END
A

REPLACE ECM (Click here)