DTC B1800/51 Short in Driver Side Squib Circuit |
DTC B1801/51 Open in Driver Side Squib Circuit |
DTC B1802/51 Short to GND in Driver Side Squib Circuit |
DTC B1803/51 Short to B+ in Driver Side Squib Circuit |
| DTC No. | Detection Condition | Trouble Area |
| B1800/51 |
|
|
| B1801/51 |
|
|
| B1802/51 |
|
|
| B1803/51 |
|
|

| 1.CHECK CONNECTOR (DRIVER SIDE SQUIB - SPIRAL CABLE) |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the connectors from the steering pad.
Check the spiral cable connector and terminals (on the steering pad side) and check that the connector is properly connected to the steering pad.
| Result | Proceed to |
| No problem | A |
| Connector or terminals incorrect. | B |
| Connector connected improperly. | C |
|
| ||||
|
| ||||
| A | |
| 2.CHECK STEERING PAD (DRIVER SIDE SQUIB) |
![]() |
Disconnect the connectors from the steering pad.
Connect the white wire side of SST (resistance 2.1 Ω) to connector E (orange connector).
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Turn the steering wheel lock to lock 5 times or more.
Check the DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 3.CHECK CONNECTOR (SPIRAL CABLE - INSTRUMENT PANEL WIRE) |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the SST from connector E.
Check the instrument panel wire connector and terminals (on the spiral cable side) and check that the connector is properly connected to the spiral cable.
| Result | Proceed to |
| No problem | A |
| Connector or terminals incorrect. | B |
| Connector connected improperly. | C |
|
| ||||
|
| ||||
| A | |
| 4.CHECK DRIVER SIDE SQUIB CIRCUIT |
![]() |
Disconnect the connector from the center airbag sensor assembly.
Check for short to B+ in the circuit.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 2 (D+) - Body ground | Ignition switch ON | Below 1 V |
| 1 (D-) - Body ground | Ignition switch ON | Below 1 V |
Check for open in the circuit.
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2 (D+) - 1 (D-) | Always | Below 1 Ω |
Check for short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2 (D+) - Body ground | Always | 1 MΩ or higher |
| 1 (D-) - Body ground | Always | 1 MΩ or higher |
Check for short in the circuit.
Release the activation prevention mechanism built into connector D (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (D+) - 2 (D-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector D to the original condition.
|
| ||||
| OK | |
| 5.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Connect the connectors to the steering pad, spiral cable and the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 6.CHECK CONNECTOR (CENTER AIRBAG SENSOR ASSEMBLY - INSTRUMENT PANEL WIRE) |
Disconnect the instrument panel wire connector from the center airbag sensor assembly.
Check the instrument panel wire connector and terminals (on the center airbag sensor assembly side) and check that the connector is properly connected to the center airbag sensor assembly.
| Result | Proceed to |
| No problem | A |
| Connector or terminals incorrect. | B |
| Connector connected improperly. | C |
|
| ||||
|
| ||||
| A | |
| 7.CHECK INSTRUMENT PANEL WIRE |
Disconnect the instrument panel wire connector from the center airbag sensor assembly.
![]() |
Check for short to B+ in the circuit.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E18-1 (D+) - Body ground | Ignition switch ON | Below 1 V |
| E18-2 (D-) - Body ground | Ignition switch ON | Below 1 V |
Check for open in the circuit.
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E18-1 (D+) - E18-2 (D-) | Always | Below 1 Ω |
Check for short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E18-1 (D+) - Body ground | Always | 1 MΩ or higher |
| E18-2 (D-) - Body ground | Always | 1 MΩ or higher |
Check for short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E18-1 (D+) - E18-2 (D-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to the original condition.
|
| ||||
| OK | ||
| ||