Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1805/52    Short in Front Passenger Side Squib Circuit

DTC    B1806/52    Open in Front Passenger Side Squib Circuit

DTC    B1807/52    Short to GND in Front Passenger Side Squib Circuit

DTC    B1808/52    Short to B+ in Front Passenger Side Squib Circuit

for Preparation Click here


DESCRIPTION

The front passenger side squib circuit consists of the center airbag sensor assembly and the front passenger airbag assembly.
The circuit signals the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the front passenger side squib circuit.

DTC No.
Detection Condition
Trouble Area
B1805/52
  1. Center airbag sensor assembly detects line short circuit signal in front passenger side squib circuit 5 times during primary check.
  2. Front passenger side squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Instrument panel wire assembly
  3. Front passenger airbag assembly (Front passenger side squib)
  4. Center airbag sensor assembly
B1806/52
  1. Center airbag sensor assembly detects open circuit signal in front passenger side squib circuit for 2 seconds.
  2. Front passenger side squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Instrument panel wire assembly
  3. Front passenger airbag assembly (Front passenger side squib)
  4. Center airbag sensor assembly
B1807/52
  1. Center airbag sensor assembly detects short circuit to ground signal in front passenger side squib circuit for 0.5 seconds.
  2. Front passenger side squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Instrument panel wire assembly
  3. Front passenger airbag assembly (Front passenger side squib)
  4. Center airbag sensor assembly
B1808/52
  1. Center airbag sensor assembly detects short circuit to B+ signal in front passenger side squib circuit for 0.5 seconds.
  2. Front passenger side squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Instrument panel wire assembly
  3. Front passenger airbag assembly (Front passenger side squib)
  4. Center airbag sensor assembly

WIRING DIAGRAM


C127736E04


INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting "check mode" (signal check) with the Techstream (Click here).
  2. After selecting CHECK MODE (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).

1.CHECK CONNECTOR (FRONT PASSENGER AIRBAG - INSTRUMENT PANEL WIRE ASSEMBLY)
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connectors from the front passenger airbag assembly.

  1. Check the instrument panel wire assembly connector and terminals (on the front passenger airbag side) and the connector is properly connected to the front passenger airbag.

    Result:

    Result
    Proceed to
    No problem
    A
    Connector or terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPLACE INSTRUMENT PANEL WIRE ASSEMBLY

C
CONNECT CONNECTOR PROPERLY
A


2.CHECK FRONT PASSENGER AIRBAG (FRONT PASSENGER SIDE SQUIB)


    C148889E08
  1. Disconnect the connectors from the front passenger airbag assembly.

  1. Connect the white wire side of SST (resistance 2.1 Ω) to connector E (orange connector).

    CAUTION:
    Never connect a tester to the front passenger airbag assembly (front passenger side squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert the SST into the terminals of the connector when connecting.
    2. Insert the SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1805/52, B1806/52, B1807/52 and B1808/52 are not output.

    HINT:
    DTCs other than DTC B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.



NG
Go to step 3
OK

REPLACE FRONT PASSENGER AIRBAG ASSEMBLY (Click here)  

3.CHECK CONNECTOR (INSTRUMENT PANEL WIRE ASSEMBLY - INSTRUMENT PANEL WIRE)
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the SST from connector E.

  1. Check the instrument panel wire assembly connector and terminals (on the instrument panel wire side) and check that the connector is properly connected to the instrument panel wire.

    Result:

    Result
    Proceed to
    No problem
    A
    Connector or terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPLACE INSTRUMENT PANEL WIRE ASSEMBLY

C
CONNECT CONNECTOR PROPERLY
A


4.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT
  1. Disconnect the connector from the center airbag sensor assembly.



    C148890E12
  1. Check for short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester connection
      Switch Condition
      Specified Condition
      Y1-2 (P-) - Body ground
      Ignition switch ON
      Below 1 V
      Y1-1 (P+) - Body ground
      Ignition switch ON
      Below 1 V

  1. Check for open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester connection
      Condition
      Specified Condition
      Y1-2 (P-) - Y1-1 (P+)
      Always
      Below 1 Ω

  1. Check for short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester connection
      Condition
      Specified Condition
      Y1-2 (P-) - Body ground
      Always
      1 MΩ or higher
      Y1-1 (P+) - Body ground
      Always
      1 MΩ or higher

  1. Check for short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester connection
      Condition
      Specified Condition
      Y1-2 (P-) - Y1-1 (P+)
      Always
      1 MΩ or higher

    3. Restore the released activation prevention mechanism of connector B to the original condition.



NG
Go to step 6
OK


5.CHECK CENTER AIRBAG SENSOR ASSEMBLY
  1. Connect the instrument panel wire connector to the instrument panel wire assembly.



    C146252E04
  1. Connect the connectors to the front passenger airbag assembly and the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1805/52, B1806/52, B1807/52 and B1808/52 are not output.

    HINT:
    DTCs other than DTC B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)  

6.CHECK CONNECTOR (INSTRUMENT PANEL WIRE - CENTER AIRBAG SENSOR ASSEMBLY)
  1. Disconnect the connector from the center airbag sensor assembly.

  1. Check the instrument panel wire connector and terminals (on the center airbag sensor assembly side) and check that the connector is properly connected to the center airbag sensor assembly.

    Result:

    Result
    Proceed to
    No problem
    A
    Connector or terminals incorrect.
    B
    Connector connected improperly.
    C



B
REPLACE INSTRUMENT PANEL WIRE

C
CONNECT CONNECTOR PROPERLY
A


7.CHECK INSTRUMENT PANEL WIRE


    C192799E01
  1. Check for short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester connection
      Switch Condition
      Specified Condition
      EY1-1 (P+) -
      Body ground
      Ignition switch ON
      Below 1 V
      EY1-2 (P-) -
      Body ground
      Ignition switch ON
      Below 1 V

  1. Check for open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester connection
      Condition
      Specified Condition
      EY1-1 (P+) - EY1-2 (P-)
      Always
      Below 1 Ω

  1. Check for short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester connection
      Condition
      Specified Condition
      EY1-1 (P+) -
      Body ground
      Always
      1 MΩ or higher
      EY1-2 (P-) -
      Body ground
      Always
      1 MΩ or higher

  1. Check for short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester connection
      Condition
      Specified Condition
      EY1-1 (P+) - EY1-2 (P-)
      Always
      1 MΩ or higher

    3. Restore the released activation prevention mechanism of connector B to the original condition.



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE INSTRUMENT PANEL WIRE ASSEMBLY