Home › SUSPENSION & AXLE › TIRE AND WHEEL › TIRE PRESSURE WARNING SYSTEM

TIRE PRESSURE WARNING SYSTEM > DIAGNOSIS SYSTEM

for Preparation Click here



CHECK WARNING LIGHT

NOTICE:
  1. When there is a problem with the tire pressure warning system, the tire pressure warning light blinks at 0.5 second intervals, and illuminates after 1 minute.
  2. When the malfunction has been corrected, the tire pressure warning light does not illuminate.
  3. When the tire pressure warning light illuminates, immediately check the tire pressures of the tires and adjust them to the specified value(s).
  4. After turning the ignition switch to ON, the tire pressure warning light illuminates for 3 seconds and then goes off. If the warning light does not illuminate for 3 seconds, proceed to the troubleshooting for the tire pressure warning light circuit (Click here).



    C213286E02
  1. Turn the ignition switch to ON.
    Text in Illustration 
    *1
    Tire Pressure Warning Light

  2. Check that the tire pressure warning light illuminates for 3 seconds.


WHAT TO CONSIDER WHEN TIRE PRESSURE WARNING LIGHT ILLUMINATES
  1. When the tire pressure warning light does not go off, or when it illuminates during driving, check the tire pressure. If the tire pressure warning light illuminates within several hours after adjusting the tire pressure, the tire may have a slow air leak.

  2. The system will not operate under the following conditions (when the problem is corrected, operation will return to normal).

    1. Tires without a tire pressure warning valve and transmitter are used.

    2. A tire pressure warning valve and transmitter ID is not registered in the tire pressure warning ECU.

    3. The tire pressure is abnormally high (absolute pressure: 637.5 kPa (6.5 kgf/cm2, 92 psi) or more; relative pressure: 500 kPa (5.1 kgf/cm2, 73 psi) or more).

    4. A tire pressure warning valve and transmitter battery is depleted (battery life: 10 years).

  3. The system may not operate under the following conditions (when the problem is corrected, operation will return to normal).

    1. Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.

    2. A radio device of similar frequencies is used in the vehicle.

    3. A type of film that affects radio waves is attached to the windows.

    4. A large amount of snow or ice is stuck to the vehicle, especially onto the wheels and around the wheel wells.

    5. Any wheels other than the specified ones are used.

    6. Tire chains are used.

    7. A large metallic object which can interfere with signal reception is put in the luggage room.

    8. The spare tire is not within the receivable range of the tire pressure warning antenna and receiver.

    9. Tire repair kit is used.


TIRE PRESSURE WARNING LIGHT AND INDICATOR CHART

HINT:
The table below indicates the state of the tire pressure warning light after the ignition switch is turned to ON.


Immediately after turning the ignition switch to ON
Always
Warning light output pattern
Illuminates for 3 seconds
Goes off
Illuminates
Blinks*1
Blinks*2
Blinks*3
Blinks*4
Outputs DTC
Normal
○
○
-
-
-
-
-
-
Low tire pressure
○
-
○
-
-
-
-
-
System failure
○
-
-
○
-
-
-
-
Test mode (signal check mode)
○
-
-
-
○
-
-
-
Initialization
○
-
-
-
-
○
-
-
ECU connector poorly connected
-
-
-
○
-
-
-
-
TC grounded (DTC is output)
○
-
-
-
-
-
-
○
TC grounded (DTC is not output)
○
-
-
-
-
-
○
-


  1. E133091E06
    *1: Illuminates and goes off repeatedly at 0.5 second intervals, and illuminates after 1 minute.
    Text in Illustration 
    *a
    ON
    *b
    OFF
    *c
    0.5 seconds
    *d
    1 minute

  2. C110635E15
    *2: Illuminates and goes off repeatedly at 0.125 second intervals.
    Text in Illustration 
    *a
    ON
    *b
    OFF
    *c
    0.125 seconds

  3. C110636E11
    *3: Blinks 3 times (1 second on, 1 second off).
    Text in Illustration 
    *a
    ON
    *b
    OFF
    *c
    1 second

  4. C145821E05
    *4: Illuminates and goes off repeatedly at 0.25 second intervals.
    Text in Illustration 
    *a
    ON
    *b
    OFF
    *c
    0.25 seconds

Normal mode DTCs
  1. DTCs are stored in the tire pressure warning ECU and output by the blinking of tire pressure warning light or by using the Techstream (Click here).


Test mode (signal check mode) DTCs
  1. By switching from normal mode into test mode (signal check mode) (input signal check), you can inspect the tire pressure warning antenna and receiver, each tire pressure warning valve and transmitter, and vehicle speed sensor signal (Click here).


FAIL-SAFE FUNCTION
  1. When a system malfunction occurs in the tire pressure warning system, the tire pressure warning light illuminates after blinking for 1 minute to inform the driver of the system failure.

  2. The result of this diagnosis code is stored in the tire pressure warning ECU.