DTC P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1) |
DTC P2238 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1) |
DTC P2239 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1) |
DTC P2240 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 2 Sensor 1) |
DTC P2241 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 2 Sensor 1) |
DTC P2242 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 2 Sensor 1) |
DTC P2252 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1) |
DTC P2253 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1) |
DTC P2255 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 2 Sensor 1) |
DTC P2256 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 2 Sensor 1) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P2237 P2240 | Open in the circuit between terminals A1A+/A2A+ and A1A-/A2A- of the A/F sensor while engine is running (2 trip detection logic) |
|
| P2238 P2241 | When one of following conditions met. (2 trip detection logic)
|
|
| P2239 P2242 | A1A+/A2A+ voltage more than 4.5 V (2 trip detection logic) |
|
| P2252 P2255 | A1A-/A2A- voltage 0.5 V or less (2 trip detection logic) |
|
| P2253 P2256 | A1A-/A2A- voltage more than 4.5 V (2 trip detection logic) |
|
| Related DTCs | P2237: Air fuel ratio sensor (for bank 1 sensor 1) open circuit between A1A+ and A1A- P2238: Air fuel ratio sensor (for bank 1 sensor 1) short circuit between A1A+ and A1A- P2238: Air fuel ratio sensor (for bank 1 sensor 1) short circuit between A1A+ and GND P2238: Air fuel ratio sensor (for bank 1 sensor 1) low impedance P2239: Air fuel ratio sensor (for bank 1 sensor 1) short circuit between A1A+ and +B P2240: Air fuel ratio sensor (for bank 2 sensor 1) open circuit between A2A+ and A2A- P2241: Air fuel ratio sensor (for bank 2 sensor 1) short circuit between A2A+ and A2A- P2241: Air fuel ratio sensor (for bank 2 sensor 1) short circuit between A2A+ and GND P2241: Air fuel ratio sensor (for bank 2 sensor 1) low impedance P2242: Air fuel ratio sensor (for bank 2 sensor 1) short circuit between A2A+ and +B P2252: Air fuel ratio sensor (for bank 1 sensor 1) short circuit between A1A- and GND P2253: Air fuel ratio sensor (for bank 1 sensor 1) short circuit between A1A- and +B P2255: Air fuel ratio sensor (for bank 2 sensor 1) short circuit between A2A- and GND P2256: Air fuel ratio sensor (for bank 2 sensor 1) short circuit between A2A- and +B |
| Required Sensors/Components (Main) | Air fuel ratio sensor |
| Required Sensors/Components (Related) | Engine coolant temperature sensor, Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Duration | 10 seconds: P2237, P2240 (Air fuel ratio sensor open circuit) and P2238, P2241 (Air fuel ratio sensor low impedance) 5 seconds: Others |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | P0016, P0018 (VVT system - misalignment) P0017, P0019 (Exhaust VVT system - misalignment) P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater) P0102, P0103 (Mass air flow meter) P0112, P0113 (Intake air temperature sensor) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120 - P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient engine coolant temperature for closed loop fuel control) P0128 (Thermostat) P0171, P0172, P0174, P0175 (Fuel system) P0301 - P0306 (Misfire) P0335 (Crankshaft position sensor) P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor) P0412, P0418, P1613 (Secondary air injection system control) P0416, P0417, P2440 - P2445 (Secondary air injection system) P0451 - P0453 (EVAP system) P0500, P0722 (Vehicle speed sensor) P0505 (IAC valve) P219A, P219B (Air-fuel ratio imbalance) |
| Monitor runs whenever following DTCs not present | None |
| Estimated sensor temperature | 450 to 550°C (842 to 1022°F) |
| Engine | Running |
| Battery voltage | 11 V or more |
| Ignition switch | ON |
| Time after ignition switch is off to ON | 5 seconds or more |
| Estimated sensor temperature | 700 to 800°C (1292 to 1472°F) |
| Engine coolant temperature | 0°C (32°F) or more |
| Fuel cut | Not executed |
| Battery voltage | 11 V or more |
| Ignition switch | ON |
| Time after ignition switch off to ON | 5 seconds or more |
| A/F sensor admittance | Less than 0.002 1/Ω |
| A/F sensor admittance | Less than 0.0074 1/Ω |
| A1A+/A2A+ terminal voltage | 0.5 V or less |
| A1A+/A2A+ terminal voltage | More than 4.5 V |
| A1A-/A2A- terminal voltage | 0.5 V or less |
| A1A-/A2A- terminal voltage | More than 4.5 V |
| Difference between A1A+ and A1A-/A2A+ and A2A- terminal voltage | 0.1 V or less |
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
Disconnect the B33 and B31 A/F sensor connectors.
Disconnect the B50 and B49 ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B33-1 (HA1A) - B50-17 (HA1A) | Always | Below 1 Ω |
| B33-3 (A1A+) - B49-1 (A1A+) | Always | Below 1 Ω |
| B33-4 (A1A-) - B49-2 (A1A-) | Always | Below 1 Ω |
| B31-1 (HA2A) - B50-19 (HA2A) | Always | Below 1 Ω |
| B31-3 (A2A+) - B49-7 (A2A+) | Always | Below 1 Ω |
| B31-4 (A2A-) - B49-8 (A2A-) | Always | Below 1 Ω |
| B33-1 (HA1A) or B50-17 (HA1A) - Body ground | Always | 10 kΩ or higher |
| B33-3 (A1A+) or B49-1 (A1A+) - Body ground | Always | 10 kΩ or higher |
| B33-4 (A1A-) or B49-2 (A1A-) - Body ground | Always | 10 kΩ or higher |
| B31-1 (HA2A) or B50-19 (HA2A) - Body ground | Always | 10 kΩ or higher |
| B31-3 (A2A+) or B49-7 (A2A+) - Body ground | Always | 10 kΩ or higher |
| B31-4 (A2A-) or B49-8 (A2A-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 2.REPLACE AIR FUEL RATIO SENSOR |
Replace the A/F sensor (Click here).
| NEXT | |
| 3.CHECK WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2237, P2238, P2239, P2252, P2253, P2255 or P2256.
Check the DTC judgment.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P2237, P2238, P2239, P2252, P2253, P2255 or P2256 is output) | B |
|
| ||||
| A | ||
| ||