DTC B1815/54 Short in Front Passenger Side Squib 2nd Step Circuit |
DTC B1816/54 Open in Front Passenger Side Squib 2nd Step Circuit |
DTC B1817/54 Short to GND in Front Passenger Side Squib 2nd Step Circuit |
DTC B1818/54 Short to B+ in Front Passenger Side Squib 2nd Step Circuit |
| DTC No. | Detection Condition | Trouble Area |
| B1815/54 |
|
|
| B1816/54 |
|
|
| B1817/54 |
|
|
| B1818/54 |
|
|

| 1.CHECK CONNECTOR (FRONT PASSENGER AIRBAG - INSTRUMENT PANEL WIRE ASSEMBLY) |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the connector from the front passenger airbag.
Check the instrument panel wire assembly connector and terminals (on the front passenger airbag side) and the connector is properly connected to the front passenger airbag.
| Result | Proceed to |
| No problem. | A |
| Connector or terminals incorrect. | B |
| Connector connected improperly. | C |
|
| ||||
|
| ||||
| A | |
| 2.CHECK FRONT PASSENGER AIRBAG (FRONT PASSENGER SIDE SQUIB 2ND STEP) |
![]() |
Disconnect the connectors from the front passenger airbag assembly.
Connect the white wire side of SST (resistance 2.1 Ω) to connector E (black connector).
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 3.CHECK CONNECTOR (INSTRUMENT PANEL WIRE ASSEMBLY - INSTRUMENT PANEL WIRE) |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the SST from connector E.
Check the instrument panel wire assembly connector and terminals (on the instrument panel wire side) and check that the connector is properly connected to the instrument panel wire.
| Result | Proceed to |
| No problem. | A |
| Connector or terminals incorrect. | B |
| Connector connected improperly. | C |
|
| ||||
|
| ||||
| A | |
| 4.CHECK FRONT PASSENGER SIDE SQUIB 2ND STEP |
Disconnect the connector from the center airbag sensor assembly.
![]() |
Check for short to B+ in the circuit.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| Y2-2 (P2-) - Body ground | Ignition switch ON | Below 1 V |
| Y2-1 (P2+) - Body ground | Ignition switch ON | Below 1 V |
Check for open in the circuit.
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Y2-2 (P2-) - Y2-1 (P2+) | Always | Below 1 Ω |
Check for short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Y2-2 (P2-) - Body ground | Always | 1 MΩ or higher |
| Y2-1 (P2+) - Body ground | Always | 1 MΩ or higher |
Check for short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Y2-2 (P2-) - Y2-1 (P2+) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to the original condition.
|
| ||||
| OK | |
| 5.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
Connect the instrument panel wire connector to the instrument panel wire assembly.
![]() |
Connect the connectors to the front passenger airbag assembly and the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 6.CHECK CONNECTOR (INSTRUMENT PANEL WIRE - CENTER AIRBAG SENSOR ASSEMBLY) |
Disconnect the connector from the center airbag sensor assembly.
Check the instrument panel wire connector and terminals (on the center airbag sensor assembly side) and check that the connector is properly connected to the center airbag sensor assembly.
| Result | Proceed to |
| No problem. | A |
| Connector or terminals incorrect. | B |
| Connector connected improperly. | C |
|
| ||||
|
| ||||
| A | |
| 7.CHECK INSTRUMENT PANEL WIRE |
![]() |
Check for short to B+ in the circuit.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| EY1-3 (P2+) - Body ground | Ignition switch ON | Below 1 V |
| EY1-4 (P2-) - Body ground | Ignition switch ON | Below 1 V |
Check for open in the circuit.
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| EY1-3 (P2+) - EY1-4 (P2-) | Always | Below 1 Ω |
Check for short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| EY1-3 (P2+) - Body ground | Always | 1 MΩ or higher |
| EY1-4 (P2-) - Body ground | Always | 1 MΩ or higher |
Check for short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| EY1-3 (P2+) - EY1-4 (P2-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to the original condition.
|
| ||||
| OK | ||
| ||