Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1653/35    Seat Position Airbag Sensor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The seat position airbag sensor circuit consists of the center airbag sensor assembly, front seat inner belt assembly LH and seat position airbag sensor.
DTC B1653/35 is stored when a malfunction is detected in the seat position airbag sensor circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1653/35
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat position airbag sensor circuit.
  2. Front seat inner belt assembly LH malfunction
  3. Seat position airbag sensor malfunction
  4. Center airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. Front seat inner belt assembly LH
  3. Seat position airbag sensor
  4. Center airbag sensor assembly

WIRING DIAGRAM


C268579E03


INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

1.CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and seat position airbag sensor. Also check that the connectors that link the No. 2 floor wire and front seat inner belt assembly LH are properly connected.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the center airbag sensor assembly and seat position airbag sensor. Also check that the connectors that link the No. 2 floor wire and front seat inner belt assembly LH are properly connected.

  1. Check that the terminals of connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


2.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (OPEN)


    C268855E01
  1. Connect the connectors to the front seat inner belt assembly LH and No. 2 floor wire.

  1. Using a service wire, connect terminals 9 (LSP+) and 17 (LSP-) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (LSP+) - 1 (LSP-)
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *3
    Service Wire
    *a
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *b
    Front view of wire harness connector
    (to Seat Position Airbag Sensor)



NG
Go to step 8
OK


3.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO GROUND)
  1. Disconnect the service wire from connector B.



    C268854E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (LSP+) - Body ground
    Always
    1 MΩ or higher
    1 (LSP-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *a
    Front view of wire harness connector
    (to Seat Position Airbag Sensor)



NG
Go to step 9
OK


4.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT)


    C268854E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (LSP+) - 1 (LSP-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *a
    Front view of wire harness connector
    (to Seat Position Airbag Sensor)



NG
Go to step 10
OK


5.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO B+)


    C268854E01
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (LSP+) - Body ground
    Ignition switch ON
    Below 1 V
    1 (LSP-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *a
    Front view of wire harness connector
    (to Seat Position Airbag Sensor)



NG
Go to step 11
OK


6.CHECK DTC


    C268869E01
  1. Connect the connectors to the center airbag sensor assembly and seat position airbag sensor.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.
    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly



NG
Go to step 7
OK

USE SIMULATION METHOD TO CHECK (Click here)  

7.CHECK SEAT POSITION AIRBAG SENSOR


    C268869E01
  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Replace the seat position airbag sensor with a known good one (Click here).

    HINT:
    Perform the following inspection using known good parts from another vehicle if possible.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Return the seat position airbag sensor that was installed for testing to its original location (Click here).
    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

REPLACE SEAT POSITION AIRBAG SENSOR (Click here)  

8.CHECK NO. 2 FLOOR WIRE (OPEN)


    C268856E01
  1. Disconnect the No. 2 floor wire from the front seat inner belt assembly LH.

    HINT:
    The service wire has already been inserted into connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L17-2 (LSP+) - L17-4 (LSP-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from the connector B.
    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *3
    Front Seat Inner Belt Assembly LH
    *4
    No. 2 Floor Wire
    *5
    Service Wire
    *a
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *b
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly LH)



NG
REPLACE NO. 2 FLOOR WIRE
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH (Click here)  

9.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    C268868E01
  1. Disconnect the No. 2 floor wire from the front seat inner belt assembly LH.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L17-2 (LSP+) - Body ground
    Always
    1 MΩ or higher
    L17-4 (LSP-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *3
    Front Seat Inner Belt Assembly LH
    *4
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly LH)



NG
REPLACE NO. 2 FLOOR WIRE
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH (Click here)  

10.CHECK NO. 2 FLOOR WIRE (SHORT)
C268868E01
  1. Disconnect the No. 2 floor wire from the front seat inner belt assembly LH.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L17-2 (LSP+) - L17-4 (LSP-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *3
    Front Seat Inner Belt Assembly LH
    *4
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly LH)



NG
REPLACE NO. 2 FLOOR WIRE
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH (Click here)  

11.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    C268868E01
  1. Disconnect the No. 2 floor wire from the front seat inner belt assembly LH.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    L17-2 (LSP+) - Body ground
    Ignition switch ON
    Below 1 V
    L17-4 (LSP-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.
    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *3
    Front Seat Inner Belt Assembly LH
    *4
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly LH)



NG
REPLACE NO. 2 FLOOR WIRE
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH (Click here)