DTC B1782 Rear Occupant Classification Sensor LH Circuit Malfunction |
| DTC No. | DTC Detecting Condition | Trouble Area |
| B1782 |
|
|

| 1.CHECK DTC |
Turn the ignition switch to the on position.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the lock position.
Turn the ignition switch to the on position.
Check the DTCs (Click here).
|
| ||||
| NG | |
| 2.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the lock position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the occupant classification ECU and the rear occupant classification sensor LH.
|
| ||||
| OK | |
| 3.CHECK NO.1 SEAT WIRE (TO B+) |
![]() |
Disconnect the connectors from the occupant classification ECU and the rear occupant classification sensor LH.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch to the on position.
Measure the voltage.
| Tester connection | Condition | Specified condition |
| Q5-3 (SGD3) - Body ground | Ignition switch on | Below 1 V |
| Q5-5 (SVC3) - Body ground | Ignition switch on | Below 1 V |
| Q5-9 (SIG3) - Body ground | Ignition switch on | Below 1 V |
|
| ||||
| OK | |
| 4.CHECK NO.1 SEAT WIRE (FOR OPEN) |
![]() |
Turn the ignition switch to the lock position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Using a service wire, connect Q2-1 (SVC3) and Q2-3 (SGD3), and connect Q2-2 (SIG3) and Q2-3 (SGD3) of connector C.
Measure the resistance.
| Tester connection | Condition | Specified condition |
| Q5-5 (SVC3) - Q5-3 (SGD3) | Always | Below 1 Ω |
| Q5-9 (SIG3) - Q5-3 (SGD3) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 5.CHECK NO.1 SEAT WIRE (FOR SHORT) |
![]() |
Disconnect the service wire from connector C.
Measure the resistance.
| Tester connection | Condition | Specified condition |
| Q5-5 (SVC3) - Q5-3 (SGD3) | Always | 1 MΩ or higher |
| Q5-9 (SIG3) - Q5-3 (SGD3) | Always | 1 MΩ or higher |
| Q5-5 (SVC3) - Q5-9 (SIG3) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 6.CHECK NO.1 SEAT WIRE (TO GROUND) |
![]() |
Measure the resistance.
| Tester connection | Condition | Specified condition |
| Q5-3 (SGD3) - Body ground | Always | 1 MΩ or higher |
| Q5-5 (SVC3) - Body ground | Always | 1 MΩ or higher |
| Q5-9 (SIG3) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 7.CHECK DTC |
Connect the connectors to the occupant classification ECU and the rear occupant classification sensor LH.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch to the on position.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the lock position.
Turn the ignition switch to the on position.
Check the DTCs (Click here).
|
| ||||
| NG | |
| 8.REPLACE OCCUPANT CLASSIFICATION ECU |
Turn the ignition switch to the lock position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the occupant classification ECU (Click here).
| NEXT | |
| 9.PERFORM ZERO POINT CALIBRATION |
Connect the negative (-) terminal cable to the battery.
Connect a Techstream to the DLC3.
Turn the ignition switch to the on position.
Using the Techstream, perform the zero point calibration (Click here).
|
| ||||
| OK | |
| 10.PERFORM SENSITIVITY CHECK |
Using a Techstream, perform the sensitivity check (Click here).
Confirm that nothing is placed on the passenger seat.
Confirm that the beginning sensor reading is within the standard range.
Place a 30 kg (66.14 lb) weight (e.g. a lead mass) onto the front passenger seat.
Confirm that the sensitivity is within the standard range.
|
| ||||
| OK | |
| 11.CHECK DTC |
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch to the on position.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the lock position.
Turn the ignition switch to the on position.
Check the DTCs (Click here).
|
| ||||
| NG | |
| 12.REPLACE FRONT SEAT ADJUSTER SUB-ASSEMBLY RH |
Turn the ignition switch to the lock position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the front seat adjuster sub-assembly RH (Click here).
| NEXT | |
| 13.PERFORM ZERO POINT CALIBRATION |
Connect the negative (-) terminal cable to the battery.
Connect a Techstream to the DLC3.
Turn the ignition switch to the on position.
Using the Techstream, perform the zero point calibration (Click here).
| NEXT | |
| 14.PERFORM SENSITIVITY CHECK |
Using a Techstream, perform the sensitivity check (Click here).
Confirm that nothing is placed on the passenger seat.
Confirm that the beginning sensor reading is within the standard range.
Place a 30 kg (66.14 lb) weight (e.g. a lead mass) onto the front passenger seat.
Confirm that the sensitivity is within the standard range.
| NEXT | ||
| ||