Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › OCCUPANT CLASSIFICATION SYSTEM

OCCUPANT CLASSIFICATION SYSTEM > Trouble in Passenger Airbag ON/OFF Indicator

for Preparation Click here


DESCRIPTION

The occupant classification system detects the front passenger seat condition and then indicates whether the front passenger airbag is activated or not through the passenger airbag ON/OFF indicator illumination.
The passenger airbag ON/OFF indicator illumination changes depending on the front passenger seat condition as shown in the table below.

Front passenger seat condition
ON Indicator
OFF Indicator
Adult is seated
ON
OFF
Child is seated
OFF
ON
Vacant
OFF
OFF
Occupant classification system failure
OFF
ON

WIRING DIAGRAM


H102275E03


INSPECTION PROCEDURE

1.CHECK SRS WARNING LIGHT
  1. Turn the ignition switch to the on position, and check the SRS warning light condition.

    OK:
    The SRS warning light does not come on.



NG
Go to step 10
OK


2.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION
  1. Turn the ignition switch to the on position.

  1. Check if the passenger airbag ON/OFF indicator correctly indicates the front passenger seat condition.

    OK:

    Front passenger seat condition
    ON Indicator
    OFF Indicator
    Adult is seated
    ON
    OFF
    Child is seated
    OFF
    ON
    Vacant
    OFF
    OFF
    Occupant classification system failure
    OFF
    ON



OK
END
NG


3.PERFORM ZERO POINT CALIBRATION
  1. Turn the ignition switch to the lock position.

  1. Connect a Techstream to the DLC3.

  1. Turn the ignition switch to the on position.

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    COMPLETED is displayed.



NG
Go to step 5
OK


4.PERFORM SENSITIVITY CHECK
  1. Using a Techstream, perform the sensitivity check (Click here).

    1. Confirm that nothing is placed on the passenger seat.

    2. Confirm that the beginning sensor reading is within the standard range.

      Standard range:
      -3.2 to 3.2 kg (-7 to 7 lb)

    3. Place a 30 kg (66.14 lb) weight (e.g. a lead mass) onto the front passenger seat.

    4. Confirm that the sensitivity is within the standard range.

      Standard range:
      27 to 33 kg (59.52 to 72.75 lb)

      HINT:
      When performing the sensitivity check, use a solid metal weight (the check result may not be accurate if a liquid weight is used).



NG
Go to step 5
OK

END 

5.RETIGHTEN FRONT SEAT ASSEMBLY RH BOLT
  1. Turn the ignition switch to the lock position.

  1. Loosen the 4 installation bolts of the front seat assembly RH.

  1. Tighten the 4 installation bolts of the front seat assembly RH to the specified torque.

Torque:
37 N*m{ 380 kgf*cm , 27 ft.*lbf }


NEXT


6.PERFORM ZERO POINT CALIBRATION
  1. Connect a Techstream to the DLC3.

  1. Turn the ignition switch to the on position.

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    COMPLETED is displayed.



NG
Go to step 8
OK


7.PERFORM SENSITIVITY CHECK
  1. Using a Techstream, perform the sensitivity check (Click here).

    1. Confirm that nothing is placed on the passenger seat.

    2. Confirm that the beginning sensor reading is within the standard range.

      Standard range:
      -3.2 to 3.2 kg (-7 to 7 lb)

    3. Place a 30 kg (66.14 lb) weight (e.g. a lead mass) onto the front passenger seat.

    4. Confirm that the sensitivity is within the standard range.

      Standard range:
      27 to 33 kg (59.52 to 72.75 lb)

      HINT:
      When performing the sensitivity check, use a solid metal weight (the check result may not be accurate if a liquid weight is used).



NG
Go to step 8
OK

END 

8.READ VALUE USING TECHSTREAM
  1. Turn the ignition switch to the on position.

  1. Using the Techstream, read Data List (Click here).

    1. Read the display when the passenger side buckle switch is operated.

      Occupant classification ECU 
      Item
      Measurement Item/
      Range (Display)
      Normal Condition
      Diagnostic Note
      Passenger Buckle SW
      Buckle switch (Front passenger side)/
      Unset: Front passenger side seat belt is unfastened
      Set: Front passenger side seat belt is fastened
      NG: Front passenger side seat belt is malfunctioning
      Unset/Set
      -

      OK:
      The Techstream display changes correctly accordance with the operation of the buckle switch.



NG
Go to step 14
OK


9.CHECK CONNECTORS
  1. Turn the ignition switch to the lock position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the occupant classification ECU and the 4 occupant classification sensors.

    OK:
    The connectors are properly connected.

  1. Disconnect the connectors from the occupant classification ECU and the 4 occupant classification sensors.

  1. Check that the connectors are not damaged or deformed.

    OK:
    The connectors are normal.



NG
REPAIR OR REPLACE WIRE HARNESS AND CONNECTOR
OK


10.CHECK DTC
  1. Connect the connectors to the occupant classification ECU and the 4 occupant classification sensors.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch to the on position, and wait for at least 60 seconds.

  1. Turn the ignition switch to the lock position.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch to the on position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC is not output.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK


11.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the ignition switch to the lock position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the occupant classification ECU (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle if possible.


NEXT


12.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery.

  1. Connect a Techstream to the DLC3.

  1. Turn the ignition switch to the on position.

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    COMPLETED is displayed.



NG
Go to step 14
OK


13.PERFORM SENSITIVITY CHECK
  1. Using a Techstream, perform the sensitivity check (Click here).

    1. Confirm that nothing is placed on the passenger seat.

    2. Confirm that the beginning sensor reading is within the standard range.

      Standard range:
      -3.2 to 3.2 kg (-7 to 7 lb)

    3. Place a 30 kg (66.14 lb) weight (e.g. a lead mass) onto the front passenger seat.

    4. Confirm that the sensitivity is within the standard range.

      Standard range:
      27 to 33 kg (59.52 to 72.75 lb)

      HINT:
      When performing the sensitivity check, use a solid metal weight (the check result may not be accurate if a liquid weight is used).



NG
Go to step 14
OK

END 

14.CHECK CONNECTORS
  1. Turn the ignition switch to the lock position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the occupant classification ECU and front seat inner belt assembly RH.

    OK:
    The connectors are properly connected.

  1. Disconnect the connectors from the occupant classification ECU and front seat inner belt assembly RH.

  1. Check that the connectors are not damaged or deformed.

    OK:
    The connectors are normal.



NG
REPAIR OR REPLACE WIRE HARNESS AND CONNECTOR
OK


15.REPLACE FRONT SEAT ADJUSTER SUB-ASSEMBLY RH
  1. Turn the ignition switch to the lock position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the front seat adjuster sub-assembly RH (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle if possible.


NEXT


16.PERFORM ZERO POINT CALIBRATION
  1. Connect the negative (-) terminal cable to the battery.

  1. Connect a Techstream to the DLC3.

  1. Turn the ignition switch to the on position.

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    COMPLETED is displayed.


NEXT


17.PERFORM SENSITIVITY CHECK
  1. Using a Techstream, perform the sensitivity check (Click here).

    1. Confirm that nothing is placed on the passenger seat.

    2. Confirm that the beginning sensor reading is within the standard range.

      Standard range:
      -3.2 to 3.2 kg (-7 to 7 lb)

    3. Place a 30 kg (66.14 lb) weight (e.g. a lead mass) onto the front passenger seat.

    4. Confirm that the sensitivity is within the standard range.

      Standard range:
      27 to 33 kg (59.52 to 72.75 lb)

      HINT:
      When performing the sensitivity check, use a solid metal weight (the check result may not be accurate if a liquid weight is used).


NEXT

END