Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1660/43    Passenger Airbag ON/OFF Indicator Circuit Malfunction

for Preparation Click here


DESCRIPTION

The passenger airbag ON/OFF indicator circuit consists of the center airbag sensor assembly and the front passenger seat belt warning light.
This circuit indicates the operation condition of the front passenger airbag assembly, the front passenger side front seat side airbag assembly and passenger side seat belt pretensioner.
DTC B1660/43 is set when a malfunction is detected in the passenger airbag ON/OFF indicator circuit.

DTC No.
Detection Condition
Trouble Area
B1660/43
  1. Center airbag sensor assembly detects line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in passenger airbag ON/OFF indicator circuit for 2 seconds
  2. Front passenger seat belt warning light malfunction
  3. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Integration control and panel assembly (Passenger airbag ON/OFF Indicator)
  3. Center airbag sensor assembly

WIRING DIAGRAM


C146242E15


INSPECTION PROCEDURE

NOTICE:
In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.

  1. Turn the ignition switch off.
  2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. Disconnect the connector from the center airbag sensor assembly.
  4. Disconnect the connectors from the steering pad.
  5. Disconnect the connectors from the front passenger airbag assembly.
  6. Disconnect the connector from the front seat outer belt assembly LH.
  7. Disconnect the connector from the front seat outer belt assembly RH.
  8. Disconnect the connector from the front seat side airbag assembly LH.
  9. Disconnect the connector from the front seat side airbag assembly RH.
  10. Disconnect the connector from the curtain shield airbag assembly LH.
  11. Disconnect the connector from the curtain shield airbag assembly RH.
1.CHECK PASSENGER AIRBAG ON/OFF INDICATOR OPERATION
  1. Turn the ignition switch to ON.



  1. Check the passenger airbag ON/OFF indicator operation.

    HINT:
    Refer to the normal condition of the passenger airbag ON/OFF indicator (Click here).


    H043700E03


    Result:

    ON/OFF Indicator Illumination
    Proceed To
    Always ON
    A
    OFF
    B



B
Go to step 6
A


2.CHECK CONNECTORS (CENTER AIRBAG SENSOR - INTEGRATION CONTROL AND PANEL)
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the instrument panel wire connectors from the center airbag sensor assembly and integration control and panel assembly.

  1. Check the instrument panel wire connectors and terminals and check that the connectors are properly connected to the center airbag sensor assembly and the integration control and panel assembly.

    Result:

    Result
    Proceed to
    No problem.
    A
    Connectors or terminals incorrect.
    B
    Connectors connect improperly.
    C



B
REPLACE INSTRUMENT PANEL WIRE

C
CONNECT CONNECTORS PROPERLY
A


3.CHECK INTEGRATION CONTROL AND PANEL ASSEMBLY (PASSENGER AIRBAG ON/OFF INDICATOR)
H102158
  1. Disconnect the connector from the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Check the passenger airbag ON/OFF indicator operation.

    OK:
    The passenger airbag ON/OFF indicator does not comes on.



NG
Go to step 5
OK


4.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    C192787E01
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Connect the connector to the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1660/43 is not output.

    HINT:
    DTCs other than B1660/43 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)  

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - INTEGRATION CONTROL AND PANEL)

C192788E01

  1. Check for short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Terminal Connection
      Switch Condition
      Specified Condition
      E29-23 (PAON) - Body ground
      Ignition switch ON
      Below 1 V
      E29-17 (P-AB) - Body ground
      Ignition switch ON
      Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check for open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Disconnect the connector from the integration control and panel assembly.

    4. Using a service wire, connect E32-17 (PAON) and E32-18 (SW-) of connector C.

      NOTICE:
      Do not forcibly insert the service wire into the terminals of the connector when connecting.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Terminal Connection
      Condition
      Specified Condition
      E29-23 (PAON) - E29-17 (P-AB)
      Always
      Below 1 Ω

  1. Check for short in the circuit.

    1. Disconnect the service wire from connector C.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Terminal Connection
      Condition
      Specified Condition
      E29-17 (P-AB) - E29-23 (PAON)
      Always
      1 MΩ or higher

  1. Check for short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Terminal Connection
      Condition
      Specified Condition
      E29-17 (P-AB) - Body ground
      Always
      1 MΩ or higher
      E29-23 (PAON) - Body ground
      Always
      1 MΩ or higher



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE INTEGRATION CONTROL AND PANEL ASSEMBLY 

6.CHECK CONNECTORS (CENTER AIRBAG SENSOR - INTEGRATION CONTROL AND PANEL)
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the instrument panel wire connectors from the center airbag sensor assembly and integration control and panel assembly.

  1. Check the instrument panel wire connectors and terminals and check that the connectors are properly connected to the center airbag sensor assembly and the integration control and panel assembly.

    Result:

    Result
    Proceed to
    No problem.
    A
    Connectors or terminals incorrect.
    B
    Connectors connected improperly.
    C



B
REPLACE INSTRUMENT PANEL WIRE

C
CONNECT CONNECTORS PROPERLY
A


7.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - INTEGRATION CONTROL AND PANEL)

C192788E01

  1. Check for short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Terminal Connection
      Switch Condition
      Specified Condition
      E29-23 (PAON) - Body ground
      Ignition switch ON
      Below 1 V
      E29-17 (P-AB) - Body ground
      Ignition switch ON
      Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check for open in the circuit.

    1. Disconnect the connector from the integration control and panel assembly.

    2. Using a service wire, connect E32-17 (PAON) and E32-18 (SW-) of connector C.

      NOTICE:
      Do not forcibly insert the service wire into the terminals of the connector when connecting.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Terminal Connection
      Condition
      Specified Condition
      E29-23 (PAON) - E29-17 (P-AB)
      Always
      Below 1 Ω

  1. Check for short in the circuit.

    1. Disconnect the service wire from connector C.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Terminal Connection
      Condition
      Specified Condition
      E29-17 (P-AB) - E29-23 (PAON)
      Always
      1 MΩ or higher

  1. Check for short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Terminal Connection
      Condition
      Specified Condition
      E29-17 (P-AB) - Body ground
      Always
      1 MΩ or higher
      E29-23 (PAON) - Body ground
      Always
      1 MΩ or higher



NG
REPLACE INSTRUMENT PANEL WIRE
OK


8.CHECK WIRE HARNESS (POWER SOURCE)
C192789E01
  1. Reconnect the connector of the instrument panel wire to the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Terminal Connection
    Switch Condition
    Specified Condition
    E32-1 (IG+) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE POWER SOURCE CIRCUIT
OK


9.CHECK INTEGRATION CONTROL AND PANEL ASSEMBLY (PASSENGER AIRBAG ON/OFF INDICATOR)
C159497E06
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Connect the connector from the integration control and panel assembly.

  1. Disconnect the connectors from the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Check the indicator according to the value(s) in the table below.

    OK:
    Connection
    Switch Condition
    Passenger Airbag ON/OFF Indicator
    E29-23 (PAON) - Body ground
    Ignition switch ON
    "ON" comes on
    E29-17 (P-AB) - Body ground
    Ignition switch ON
    "OFF" comes on



NG
REPLACE INTEGRATION CONTROL AND PANEL ASSEMBLY
OK


10.CHECK CENTER AIRBAG SENSOR ASSEMBLY
C192787E01
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Connect the connector to the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1660/43 is not output.

    HINT:
    DTCs other than B1660/43 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)