DTC B1825/56 Short in Side Squib LH Circuit |
DTC B1826/56 Open in Side Squib LH Circuit |
DTC B1827/56 Short to GND in Side Squib LH Circuit |
DTC B1828/56 Short to B+ in Side Squib LH Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1825/56 |
|
|
| B1826/56 |
| |
| B1827/56 |
| |
| B1828/56 |
|

| 1.CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connectors are properly connected to the front seat airbag assembly LH and center airbag sensor assembly.
Disconnect the connectors from the front seat airbag assembly LH and center airbag sensor assembly.
Check that the terminals of the connectors are not damaged.
Check that the short spring for the No. 2 floor wire with the activation prevention mechanism is not deformed or damaged.
|
| ||||
| OK | |
| 2.CHECK FRONT SEAT AIRBAG ASSEMBLY LH |
![]() |
Connect the connector to the center airbag sensor assembly.
Connect SST (resistance 2.1 Ω) to connector C.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Disconnect SST from connector C.
| *1 | Front Seat Airbag Assembly LH |
| *2 | Center Airbag Sensor Assembly |
| *a | Front view of wire harness connector (to Front Seat Airbag Assembly LH) |
|
| ||||
| OK | ||
| ||
| 3.CHECK NO. 2 FLOOR WIRE |
![]() |
Disconnect the No. 2 floor wire from the center airbag sensor assembly.
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| La1-1 (SFL+) - Body ground | Ignition switch ON | Below 1 V |
| La1-2 (SFL-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Check for an open in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| La1-1 (SFL+) - La1-2 (SFL-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| La1-1 (SFL+) - Body ground | Always | 1 MΩ or higher |
| La1-2 (SFL-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| La1-1 (SFL+) - La1-2 (SFL-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to the original condition.
| *1 | Front Seat Airbag Assembly LH |
| *2 | Center Airbag Sensor Assembly |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector (to Front Seat Airbag Assembly LH) |
|
| ||||
| OK | |
| 4.CHECK DTC |
![]() |
Connect the connectors to the front seat airbag assembly LH and center airbag sensor assembly.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| *1 | Front Seat Airbag Assembly LH |
| *2 | Center Airbag Sensor Assembly |
|
| ||||
| OK | ||
| ||