Home › BODY ELECTRICAL › METER › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Speedometer Malfunction

for Preparation Click here


DESCRIPTION

The meter CPU receives vehicle speed signals from the skid control ECU via the CAN communication system. The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. The skid control ECU supplies power to the vehicle speed sensor. The skid control ECU detects vehicle speed signals based on the pulses of the voltage.

HINT:
  1. Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click here).
  2. If the vehicle speed sensor circuit has a malfunction, the skid control ECU stores the DTCs. Troubleshoot the Vehicle Stability Control System (Click here).


WIRING DIAGRAM


E143765E57


INSPECTION PROCEDURE

CAUTION:
If the vehicle speed is outside the allowable range when tested, perform the on-vehicle inspection (Click here).

HINT:
Before starting the following inspection, check tire size and tire air pressure.

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication DTC is output (Click here).
    Result 
    Result
    Proceed to
    CAN communication DTC is not output
    A
    CAN communication DTC is output
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (SPEED METER OPERATION)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Combination Meter / Active Test.

  1. According to the display on the Techstream, perform the Active Test.

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Speed Meter Operation
    Speedometer
    OFF/0/40/80/120/160*1/200*1 km/h (mph)
    Perform the test with the vehicle stopped and the engine idling.
    Acceptable range (km/h or mph): [Control range → Speedometer display]
    for mph
    1. 40 → 39.1 to 41.9
    2. 80 → 79.3 to 82.5
    for km/h
    1. 40 → 38.3 to 42.8
    2. 80 → 78.4 to 83.4
    3. 120 → 118.9 to 123.9
    4. 160 → 159.3 to 164.3

    1. *1: except U.S.A.

    OK:
    Speedometer indication is normal.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


3.READ VALUE USING TECHSTREAM (VEHICLE SPEED METER)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Combination Meter / Data List.

  1. According to the display on the Techstream, read the Data List.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed Meter
    Vehicle speed/
    Min.: 0 (0), Max.: 255 (158)
    Approximately same as actual vehicle speed (When vehicle is being driven)
    Unit: km/h (mph)

    OK:
    Vehicle speed displayed on the Techstream is almost the same as the speedometer indication.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


4.CHECK VEHICLE STABILITY CONTROL SYSTEM
  1. Check if a vehicle stability control DTC is output (Click here).
    Result 
    Result
    Proceed to
    Vehicle stability control DTC is not output
    A
    Vehicle stability control DTC is output
    B



B
GO TO VEHICLE STABILITY CONTROL SYSTEM (Click here)
A

REPLACE COMBINATION METER ASSEMBLY (Click here)