Home › BODY ELECTRICAL › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM

POWER DOOR LOCK CONTROL SYSTEM > All Doors cannot be Locked / Unlocked Simultaneously

for Preparation Click here


DESCRIPTION

The main body ECU receives switch signals from the door control switch on the power window regulator master switch, door control switch RH, front door LH key cylinder and front door RH key cylinder, and activates the door lock motor on each door accordingly.

WIRING DIAGRAM


B293178E01


INSPECTION PROCEDURE

1.CHECK OPERATION (ALL DOORS LOCK/ UNLOCK)
  1. All doors can be locked/unlocked at once using the following:

    1. Door control switch on the power window regulator master switch (switch operation)
    2. Door control switch RH (switch operation)
    3. Door key cylinder linked with door lock on the front door LH (key operation)
    4. Door key cylinder linked with door lock on the front door RH (key operation)

  1. Proceed to the next step according to the symptom if all the doors cannot be locked / unlocked at once.
    Result 
    Result
    Proceed to
    All doors cannot be locked/unlocked at once using door control switch on power window regulator master switch
    A
    All doors cannot be locked/unlocked at once using door control switch RH
    B
    All doors cannot be locked/unlocked at once using door key cylinder on front door LH
    C
    All doors cannot be locked/unlocked at once using door key cylinder on front door RH
    D



B
Go to step 5

C
Go to step 8

D
Go to step 11
A


2.READ VALUE USING TECHSTREAM (DOOR CONTROL SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. According to the display on the Techstream, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Door Lock SW-Lock
    Door manual lock switch signal / ON or OFF
    ON: Door control switch is pushed to lock position
    OFF: Door control switch is not pushed
    -
    Door Lock SW-Unlock
    Door manual unlock switch signal / ON or OFF
    ON: Door control switch is pushed to unlock position
    OFF: Door control switch is not pushed
    -

OK:
When the switch is operated, the Techstream displays ON and OFF as shown in the table.



NG
Go to step 3
OK

REPLACE MAIN BODY ECU 

3.INSPECT POWER WINDOW REGULATOR MASTER SWITCH (DOOR CONTROL SWITCH)
  1. Inspect the power window regulator master switch (door control switch) (Click here).



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - POWER WINDOW REGULATOR MASTER SWITCH)
  1. Disconnect the 1K main body ECU connector.

  1. Disconnect the H7 power window regulator master switch connector.

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Condition
Specified Condition
1K-5 (L1) - H7-1 (L1)
Always
Below 1 Ω
1K-1 (UL1) - H7-9 (UL1)
Always
Below 1 Ω
H7-7 (E) - Body ground
Always
Below 1 Ω
1K-5 (L1) - Body ground
Always
10 kΩ or higher
1K-1 (UL1) - Body ground
Always
10 kΩ or higher

  1. Reconnect the power window regulator master switch connector.

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

5.READ VALUE USING TECHSTREAM (DOOR CONTROL SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. According to the display on the Techstream, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Door Lock SW-Lock
    Door manual lock switch signal / ON or OFF
    ON: Door control switch is pushed to lock position
    OFF: Door control switch is not pushed
    -
    Door Lock SW-Unlock
    Door manual unlock switch signal / ON or OFF
    ON: Door control switch is pushed to unlock position
    OFF: Door control switch is not pushed
    -

OK:
When the switch is operated, the Techstream displays ON and OFF as shown in the table.



NG
Go to step 6
OK

REPLACE MAIN BODY ECU 

6.INSPECT DOOR CONTROL SWITCH RH
  1. Inspect the door control switch RH (Click here).



NG
REPLACE DOOR CONTROL SWITCH RH (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOOR CONTROL SWITCH RH)
  1. Disconnect the 1K main body ECU connector.

  1. Disconnect the G8 door control switch RH connector.

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Condition
Specified Condition
1K-5 (L1) - G8-4
Always
Below 1 Ω
1K-1 (UL1) - G8-2
Always
Below 1 Ω
G8-3 - Body ground
Always
Below 1 Ω
1K-5 (L1) - Body ground
Always
10 kΩ or higher
1K-1 (UL1) - Body ground
Always
10 kΩ or higher

  1. Reconnect the door control switch RH connector.

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

8.READ VALUE USING TECHSTREAM (DOOR KEY LOCK AND UNLOCK SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. According to the display on the Techstream, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Door Key SW-Lock
    Door key linked lock switch signal / ON or OFF
    ON: Driver side door key cylinder or passenger side door key cylinder is turned to lock position
    OFF: Driver side door key cylinder or passenger side door key cylinder is not turned
    -
    D Door Key SW-UL
    Door key linked unlock switch signal / ON or OFF
    ON: Driver side door key cylinder is turned to unlock position
    OFF: Driver side door key cylinder is not turned
    -

OK:
When the door key cylinder is operating, the Techstream should display as shown in the table.



NG
Go to step 9
OK

REPLACE MAIN BODY ECU 

9.INSPECT FRONT DOOR LOCK LH
  1. Inspect the front door lock LH (Click here).



NG
REPLACE FRONT DOOR LOCK LH (Click here)
OK


10.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT DOOR LOCK LH)
  1. Disconnect the 1K and E6 main body ECU connectors.

  1. Disconnect the H6 front door lock LH connector.

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Condition
Specified Condition
1K-3 (L2) - H6-9
Always
Below 1 Ω
E6-12 (UL3) - H6-10
Always
Below 1 Ω
H6-7 - Body ground
Always
Below 1 Ω
1K-3 (L2) - Body ground
Always
10 kΩ or higher
E6-12 (UL3) - Body ground
Always
10 kΩ or higher

  1. Reconnect the front door lock LH connector.

  1. Reconnect the main body ECU connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

11.READ VALUE USING TECHSTREAM (DOOR KEY LOCK AND UNLOCK SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. According to the display on the Techstream, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Door Key SW-Lock
    Door key linked lock switch signal / ON or OFF
    ON: Driver side door key cylinder or passenger side door key cylinder is turned to lock position
    OFF: Driver side door key cylinder or passenger side door key cylinder is not turned
    -
    P Door Key SW-UL
    Door key linked unlock switch signal / ON or OFF
    ON: Passenger side door key cylinder is turned to unlock position
    OFF: Passenger side door key cylinder is not turned
    -

OK:
When the door key cylinder is operated, the Techstream displays ON and OFF as shown in the table.



NG
Go to step 12
OK

REPLACE MAIN BODY ECU 

12.INSPECT FRONT DOOR LOCK RH
  1. Inspect the front door lock RH (Click here).



NG
REPLACE FRONT DOOR LOCK RH (Click here)
OK


13.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT DOOR LOCK RH)
  1. Disconnect the 1K and E6 main body ECU connectors.

  1. Disconnect the G7 front door lock assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Condition
Specified Condition
1K-3 (L2) - G7-6
Always
Below 1 Ω
E6-22 (UL2) - G7-5
Always
Below 1 Ω
G7-8 - Body ground
Always
Below 1 Ω
1K-3 (L2) - Body ground
Always
10 kΩ or higher
E6-22 (UL2) - Body ground
Always
10 kΩ or higher

  1. Reconnect the front door lock RH connector.

  1. Reconnect the main body ECU connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU