Home › ENGINE › 1GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > Fuel Pump Control Circuit

for Preparation Click here


DESCRIPTION

The fuel pump circuit consists of the ECM, fuel pump and fuel pump control ECU assembly (which operates the fuel pump). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump control ECU assembly. Based on the signal sent from the ECM, the fuel pump control ECU assembly adjusts the fuel pump operation speed.

WIRING DIAGRAM


A287420E01


A287430E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP/SPEED)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

  1. Check whether operating sounds can be heard while operating the fuel pump using the Techstream.

    OK:
    Operating sounds can be heard from fuel pump.


    Result 
    Result
    Proceed to
    NG (w/ Secondary Air Injection System)
    A
    OK (w/ Secondary Air Injection System)
    B
    OK (w/o Secondary Air Injection System)
    C
    NG (w/o Secondary Air Injection System)
    D



B
Go to step 10

C
Go to step 15

D
Go to step 18
A


2.INSPECT FUEL PUMP CONTROL ECU ASSEMBLY (POWER SOURCE VOLTAGE)


    A243664E15
  1. Disconnect the fuel pump control ECU assembly connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-6 (+B) - Body Ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Pump Control ECU Assembly)



NG
Go to step 9
OK


3.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - BODY GROUND)
  1. Disconnect the O3 fuel pump control ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    O3-3 (E) - Body Ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP CONTROL ECU ASSEMBLY)
  1. Disconnect the L5 fuel pump connector.

  1. Disconnect the O3 fuel pump control ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    L5-4 - O3-1 (FP)
    Always
    Below 1 Ω
    L5-5 - O3-2 (FP-)
    Always
    Below 1 Ω
    L5-4 or O3-1 (FP) - Body ground
    Always
    10 kΩ or higher
    L5-5 or O3-2 (FP-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT FUEL PUMP
  1. Inspect the fuel pump (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the fuel pump (Click here).



NG
REPLACE FUEL PUMP (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM)
  1. Disconnect the O3 fuel pump control ECU assembly connector.

  1. Disconnect the E78 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    O3-5 (FPC) - E78-3 (FPC)
    Always
    Below 1 Ω
    O3-5 (FPC) or E78-3 (FPC) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.REPLACE FUEL PUMP CONTROL ECU ASSEMBLY
  1. Replace the fuel pump control ECU assembly (Click here).


NEXT


8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Check the fuel pump operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END 

9.CHECK HARNESS AND CONNECTOR (EFI RELAY - FUEL PUMP CONTROL ECU ASSEMBLY)
  1. Remove the EFI relay from the engine room relay block.

  1. Disconnect the O3 fuel pump control ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    3 (EFI relay) - O3-6 (+B)
    Always
    Below 1 Ω
    3 (EFI relay) or O3-6 (+B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO ECM POWER SOURCE CIRCUIT (Click here)  

10.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP)


    A243665E02
  1. Remove the fuel pump (Click here).

  1. Clean the fuel pump to completely remove any remaining fuel.

  1. Connect the fuel pump connector.

    CAUTION:
    Make sure that there is no fuel remaining inside or on the outside of the fuel pump.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump Duty.

  1. Operate the fuel pump using the Active Test function and measure the voltage according to the value(s) in the table below.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    FPC Duty: 25%
    3.2 to 4.05 V
    FPC Duty: 80%
    8.8 to 12.5 V

  1. Operate the fuel pump using the Active Test function and measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    ON (FPC Duty: 90%)
    9.0 to 14.0 V

    HINT:
    1. Be sure to measure the voltage with all the connectors connected.
    2. Before performing this inspection, check that the battery voltage is between 11 and 14 V (not depleted).

    Text in Illustration 
    *a
    Component with harness connected
    (Fuel Pump)



NG
Go to step 13
OK


11.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM)
  1. Disconnect the O3 fuel pump control ECU assembly connector.

  1. Disconnect the E78 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    O3-5 (FPC) - E78-3 (FPC)
    Always
    Below 1 Ω
    O3-5 (FPC) or E78-3 (FPC) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.REPLACE FUEL PUMP
  1. Replace the fuel pump (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the fuel pump (Click here).



NEXT
Go to step 14

13.REPLACE FUEL PUMP CONTROL ECU ASSEMBLY
  1. Replace the fuel pump control ECU assembly (Click here).


NEXT


14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Check the fuel pump operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END 

15.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM, BODY GROUND)
  1. Disconnect the O1 fuel pump control ECU assembly connector.

  1. Disconnect the E78 and E77 ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    O1-1 (FPC) - E78-3 (FPC)
    Always
    Below 1 Ω
    O1-2 (DI) - E77-26 (DI)
    Always
    Below 1 Ω
    O1-3 (E) - Body ground
    Always
    Below 1 Ω
    O1-1 (FPC) or E78-3 (FPC) - Body ground
    Always
    10 kΩ or higher
    O1-2 (DI) or E77-26 (DI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


16.REPLACE FUEL PUMP CONTROL ECU ASSEMBLY
  1. Replace the fuel pump control ECU assembly (Click here).


NEXT


17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Check the fuel pump operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END 

18.INSPECT CIRCUIT OPENING RELAY (C/OPN)
A126370
  1. Remove the circuit opening relay (C/OPN) from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage not applied
    10 kΩ or higher
    Battery voltage applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE CIRCUIT OPENING RELAY (C/OPN)
OK


19.INSPECT CIRCUIT OPENING RELAY (C/OPN) (POWER SOURCE VOLTAGE)
A241853E01
  1. Remove the circuit opening relay (C/OPN) from the engine room relay block.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (Circuit opening relay (C/OPN)) - Body ground
    Ignition switch ON
    11 to 14 V
    5 (Circuit opening relay (C/OPN)) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *1
    Engine Room Relay Block
    *2
    Circuit Opening Relay (C/OPN)



NG
Go to step 26
OK


20.CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY (C/OPN) - ECM, FUEL PUMP CONTROL ECU ASSEMBLY)
  1. Remove the circuit opening relay (C/OPN) from the engine room relay block.

  1. Disconnect the E77 ECM connector.

  1. Disconnect the O1 fuel pump control ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    1 (Circuit opening relay (C/OPN)) - E77-8 (FC)
    Always
    Below 1 Ω
    3 (Circuit opening relay (C/OPN)) - O1-4 (+B)
    Always
    Below 1 Ω
    1 (Circuit opening relay (C/OPN)) or E77-8 (FC) - Body ground
    Always
    10 kΩ or higher
    3 (Circuit opening relay (C/OPN)) or O1-4 (+B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


21.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP CONTROL ECU ASSEMBLY)
  1. Disconnect the L5 fuel pump connector.

  1. Disconnect the O2 fuel pump control ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    L5-4 - O2-1 (FP)
    Always
    Below 1 Ω
    L5-5 - O2-2 (FP-)
    Always
    Below 1 Ω
    L5-4 or O2-1 (FP) - Body ground
    Always
    10 kΩ or higher
    L5-5 or O2-2 (FP-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


22.INSPECT FUEL PUMP
  1. Inspect the fuel pump (Click here).



NG
REPLACE FUEL PUMP (Click here)
OK


23.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM, BODY GROUND)
  1. Disconnect the O1 fuel pump control ECU assembly connector.

  1. Disconnect the E78 and E77 ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    O1-1 (FPC) - E78-3 (FPC)
    Always
    Below 1 Ω
    O1-2 (DI) - E77-26 (DI)
    Always
    Below 1 Ω
    O1-3 (E) - Body ground
    Always
    Below 1 Ω
    O1-1 (FPC) or E78-3 (FPC) - Body ground
    Always
    10 kΩ or higher
    O1-2 (DI) or E77-26 (DI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


24.REPLACE FUEL PUMP CONTROL ECU ASSEMBLY
  1. Replace the fuel pump control ECU assembly (Click here).


NEXT


25.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Check the fuel pump operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END 

26.CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY (C/OPN) - EFI RELAY, IGNITION SWITCH)
  1. Remove the circuit opening relay (C/OPN) from the engine room relay block.

  1. Remove the EFI relay (EFI) from the engine room relay block.

  1. Disconnect the A1 ignition switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    5 (Circuit opening relay (C/OPN)) - 3 (EFI relay)
    Always
    Below 1 Ω
    2 (Circuit opening relay (C/OPN)) - A1-6 (IG2)
    Always
    Below 1 Ω
    5 (Circuit opening relay (C/OPN)) or 3 (EFI relay) - Body ground
    Always
    10 kΩ or higher
    2 (Circuit opening relay (C/OPN)) or A1-6 (IG2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO ECM POWER SOURCE CIRCUIT (Click here)