Home › BRAKE › BRAKE CONTROL › ANTI-LOCK BRAKE SYSTEM

DTC    C0210/33    Rear Speed Sensor RH Circuit

DTC    C0215/34    Rear Speed Sensor LH Circuit

DTC    C1238/38    Foreign Object is Attached on Tip of Rear Speed Sensor RH

DTC    C1239/39    Foreign Object is Attached on Tip of Rear Speed Sensor LH

DTC    C1273/73    Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)

DTC    C1274/74    Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)

DTC    C1277/77    Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)

DTC    C1278/78    Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)

for Preparation Click here


DESCRIPTION

Refer to DTCs C0200/31, C0205/32, C1235/35, and C1236/36 .
DTCs C1273/73 to C1278/78 can be deleted when the speed sensor sends a vehicle speed signal or the Test Mode ends. DTCs C1273/73 to C1278/78 are output only in the Test Mode.

DTC No.
DTC Detection Condition
Trouble Area
C0210/33
C0215/34
With vehicle speed at 6 mph (10 km/h) or more, sensor signal circuit of faulty wheel is open or short for 1 second or more.
  1. Momentary interruption of sensor signal of faulty wheel has occurred 7 times or more.
  1. Sensor signal circuit is open for 0.5 seconds or more.
  1. Rear speed sensor RH/LH
  2. Rear speed sensor RH/LH circuit
  3. Skid control rotor
  4. Sensor installation
  5. Brake actuator assembly
C1238/38
C1239/39
At vehicle speed of 12 mph (20 km/h) or more, condition that noise is included in speed sensor signal continues for 5 seconds or more.
  1. Rear speed sensor RH/LH
  2. Skid control rotor
  3. Sensor installation
  4. Brake actuator assembly

HINT:
  1. DTC C0210/33 and C1238/38 are for the rear speed sensor RH.
  2. DTC C0215/34 and C1239/39 are for the rear speed sensor LH.


WIRING DIAGRAM


C109416E01


INSPECTION PROCEDURE

HINT:
Start the inspection from step 1 when using the intelligent tester and start from step 3 when not using the intelligent tester.

1.READ VALUE OF INTELLIGENT TESTER (MOMENTARY INTERRUPTION OF REAR SPEED SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the intelligent tester main switch on.

  1. Select the DATA LIST mode on the intelligent tester.

    ABS: 
    Item (Display)
    Measurement Item / Range (Display)
    Normal Condition
    Diagnostic Note
    RR Speed Open
    Speed sensor open detection
    (RR) / OPN DET or NORMAL
    OPN DET: Momentary interruption
    NORMAL: Normal
    -
    RL Speed Open
    Speed sensor open detection
    (RL) / OPN DET or NORMAL
    OPN DET: Momentary interruption
    NORMAL: Normal
    -

  1. Check for any momentary interruption in the wire harness and connector corresponding to a DTC (Click here).

    OK:
    There are no momentary interruptions.

    HINT:
    Perform the above inspection before removing the sensor and connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SPEED SENSOR CIRCUIT)
OK


2.READ VALUE OF INTELLIGENT TESTER (REAR SPEED SENSOR)
  1. Select the DATA LIST mode on the intelligent tester.

    ABS: 
    Item (Display)
    Measurement Item / Range (Display)
    Normal Condition
    Diagnostic Note
    RR Wheel Speed
    Wheel speed sensor (RR) reading / min.: 0 mph (0 km/h), max.: 202 mph (326 km/h)
    Actual wheel speed
    Similar speed as indicated on speedometer
    RL Wheel Speed
    Wheel speed sensor (RL) reading / min.: 0 mph (0 km/h), max.: 202 mph (326 km/h)
    Actual wheel speed
    Similar speed as indicated on speedometer

  1. Check that there is the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer are almost the same when driving the vehicle.

    OK:
    The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed.



NG
Go to step 4
OK


3.PERFORM TEST MODE (SIGNAL CHECK)
  1. Clear the DTC (Click here).

  1. Perform sensor signal check in TEST MODE PROCEDURE (Click here).

    OK:
    All Test Mode DTCs are erased.



B
Go to step 9
A


4.INSPECT REAR SPEED SENSOR INSTALLATION


    BR03795E21
  1. Turn the ignition switch off.

  1. Check the speed sensor installation.

    OK:
    The installation nut is tightened properly.
    There is no clearance between the sensor and the rear axle.
    Torque:
    8.0 N*m (82 kgf*cm, 71 in.*lbf)

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



NG
INSTALL REAR SPEED SENSOR CORRECTLY OR REPLACE REAR SPEED SENSOR
OK


5.INSPECT SPEED SENSOR TIP
  1. Remove the rear speed sensor (Click here).

  1. Check the sensor tip.

    OK:
    No scratches or foreign matter on the sensor tip.

    NOTICE:
    Check the speed sensor signal after cleaning or replacement (Click here).



NG
CLEAN OR REPLACE REAR SPEED SENSOR
OK


6.INSPECT REAR SPEED SENSOR AND SKID CONTROL SENSOR WIRE


    C111158E01
  1. Install the rear speed sensor.

  1. Disconnect the rear speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    RH: 
    Tester Connection
    Specified Condition
    2 (RR+) - 1 (RR-)
    1.09+-0.2 kΩ at 20°C
    2 (RR+) - Body ground
    10 kΩ or higher
    1 (RR-) - Body ground
    10 kΩ or higher
    LH: 
    Tester Connection
    Specified Condition
    2 (RL+) - 1 (RL-)
    1.09+-0.2 kΩ at 20°C
    2 (RL+) - Body ground
    10 kΩ or higher
    1 (RL-) - Body ground
    10 kΩ or higher



    C111159E01
  1. Disconnect the skid control sensor wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    RH Side: 
    Tester Connection
    Specified Condition
    "A"-2 - "P1"-4
    Below 1 Ω
    "A"-2 - "P1"-3
    10 kΩ or higher
    "A"-2 - Body ground
    10 kΩ or higher
    "A"-1 - "P1"-3
    Below 1 Ω
    "A"-1 - "P1"-4
    10 kΩ or higher
    "A"-1 - Body ground
    10 kΩ or higher
    LH Side: 
    Tester Connection
    Specified Condition
    "B"-2 - "P1"-2
    Below 1 Ω
    "B"-2 - "P1"-1
    10 kΩ or higher
    "B"-2 - Body ground
    10 kΩ or higher
    "B"-1 - "P1"-1
    Below 1 Ω
    "B"-1 - "P1"-2
    10 kΩ or higher
    "B"-1 - Body ground
    10 kΩ or higher

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



NG
REPLACE REAR SPEED SENSOR OR SKID CONTROL SENSOR WIRE
OK


7.CHECK HARNESS AND CONNECTOR (BETWEEN SKID CONTROL ECU AND REAR SPEED SENSOR)


    C111160E01
  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    RH: 
    Tester Connection
    Specified Condition
    B19-33 (RR+) - P1-4 (RR+)
    Below 1 Ω
    B19-33 (RR+) - Body ground
    10 kΩ or higher
    B19-34 (RR-) - P1-3 (RR-)
    Below 1 Ω
    B19-34 (RR-) - Body ground
    10 kΩ or higher
    LH: 
    Tester Connection
    Specified Condition
    B19-11 (RL+) - P1-2 (RL+)
    Below 1 Ω
    B19-11 (RL+) - Body ground
    10 kΩ or higher
    B19-12 (RL-) - P1-1 (RL-)
    Below 1 Ω
    B19-12 (RL-) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT SPEED SENSOR AND SENSOR ROTOR SERRATIONS


    W004200E03
  1. Connect the oscilloscope to terminals FR+ - FR- or FL+ - FL- of the skid control ECU.

  1. Drive the vehicle at about 19 mph (30 km/h), and check the signal waveform.

    OK:
    A waveform as shown in the figure should be output.

    HINT:
    1. As vehicle speed (wheel rotation speed) increases, the width of the waveform narrows and the fluctuation in the output voltage becomes greater.
    2. When noise is identified in the waveform on the oscilloscope, error signals are generated due to rotor scratches, looseness or foreign matter attached to the speed sensor.



NG
Go to step 10
OK


9.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Drive the vehicle at a speed of approximately 20 mph (32 km/h) or more for 60 seconds or more.

  1. Check that the same DTCs are recorded (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.


    Result:

    Condition
    Proceed to
    DTCs (C0210/33, C0215/34, C1238/38 and C1239/39) are output
    A
    DTCs (C0210/33, C0215/34, C1238/38 and C1239/39) are not output (When troubleshooting in accordance with the DTC CHART)
    B
    DTCs (C0210/33, C0215/34, C1238/38 and C1239/39) are not output (When troubleshooting in accordance with the PROBLEM SYMPTOMS TABLE)
    C



B
END

C
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
A


10.INSPECT REAR SKID CONTROL ROTOR
  1. Turn the ignition switch off.

  1. Remove the rear axle shaft (Click here).

  1. Check the rotor.

    OK:
    No scratches, oil, or foreign matter on the rotors.

    NOTICE:
    Check the speed sensor signal after cleaning or replacement (Click here).



NG
CLEAN OR REPLACE REAR SKID CONTROL ROTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY