2014-2019 Hiace · Service Manual SECURITIES

HOW TO PROCEED WITH TROUBLESHOOTING

Troubleshooting · Vehicles built from Dec 2017

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

HINT:
  1. Use this procedure to troubleshoot the immobiliser system.
  2. *: Use the GTS.


1.VEHICLE BROUGHT TO WORKSHOP
    NEXT

    2.CUSTOMER PROBLEM ANALYSIS

      HINT:
      1. In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
      2. Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
      3. The following 5 items are important points for problem analysis:

      What
      Vehicle model, system name
      When
      Date, time, occurrence frequency
      Where
      Whether the problem occurs at a specific location.
      Under what conditions?
      Whether the doors were locked or unlocked, whether the engine switch was on, whether the engine was running.
      How did it happen?
      Problem symptoms
    NEXT

    3.INSPECT BATTERY VOLTAGE
    1. Measure the battery voltage.

      Standard voltage:
      11 to 14 V

      1. If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.

      HINT:
      A simple method to determine whether the battery is discharged is to operate the horn.

    NEXT

    4.TURN ENGINE SWITCH ON (IG)

      HINT:
      When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start (CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

    NEXT

    5.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
    1. Using the GTS, check for CAN communication system DTCs (Click here).

      Result 
      Result
      Proceed to
      CAN DTC is not output
      A
      CAN DTC is output
      B


    B.
    A

    6.CHECK COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*
    1. Using the GTS, check for LIN communication system DTCs (Click here).

      Result 
      Result
      Proceed to
      LIN DTC is not output
      A
      LIN DTC is output
      B


    B.
    A

    7.CHECK FOR DTC*
    1. Check for DTCs and make a note of any codes that are output (Click here).

    2. Based on the DTCs output above, proceed to each diagnostic procedure.

      Result 
      Result
      Proceed to
      DTCs are not output
      A
      ECD system DTCs are output
      B
      Steering lock system DTCs are output
      C
      Immobiliser system DTCs are output
      D


    B.

    C.

    D.
    A

    8.PROBLEM SYMPTOMS TABLE
    1. Refer to Problem Symptoms Table (Click here).

      Result 
      Result
      Proceed to
      Fault is not listed in problem symptoms table
      A
      Fault is listed in problem symptoms table
      B


    B.
    A

    9.OVERALL ANALYSIS AND TROUBLESHOOTING*
    1. Data List / Active Test (Click here)

    2. Terminals of ECU (Click here)

    NEXT

    10.REPAIR OR REPLACE

      HINT:
      If the certification ECU (smart key ECU assembly), ID code box (immobiliser code ECU), ECM, or electrical key transmitter sub-assembly are replaced, refer to Service Bulletin.

    NEXT

    11.CHECK FOR DTC*
    1. Clear the DTCs (Click here).

    2. Check for DTCs (Click here).

      HINT:
      Before checking for DTCs, perform the "DTC Output Confirmation Operation" of each diagnostic procedure (Click here).

      Result 
      Result
      Proceed to
      DTCs are not output
      A
      Immobiliser system DTCs are output
      B


    B.
    A

    ← HOW TO PROCEED WITH TROUBLESHOOTING (Jan 2017 – Nov 2017)PROBLEM SYMPTOMS TABLE (Oct 2014 – Dec 2014) →