2014-2019 Hiace · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Dec 2017

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. After removing the injection pipes, clean them with a brush and compressed air.


1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start up the engine.

  1. Turn the A/C switch on.

  1. Operate the cooler compressor at an engine rpm of approximately 1,000 for 5 to 6 minutes to circulate the refrigerant and collect compressor oil remaining in each component into the cooler compressor as much as possible.

  1. Stop the engine.

  1. Using SST, let the refrigerant gas out.

    SST
    07110-58060   (07117-58080, 07117-58090, 07117-78050, 07117-88060, 07117-88070, 07117-88080)


3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

4. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    A316609E01

    Text in Illustration 
    *1
    Bleeder Plug
    *2
    Radiator Reservoir Cap Sub-assembly
    *3
    Radiator Reservoir Assembly
    *4
    Cylinder Block Drain Cock Plug
    *5
    Radiator Drain Cock Plug
    -
    -

  1. Remove the radiator reservoir cap sub-assembly.

  1. Loosen the cylinder block drain cock plug (on the engine oil cooler cover), and drain the engine coolant.

  1. Tighten the radiator drain cock plug.

  1. Tighten the cylinder block drain cock plug (on the engine oil cooler cover).

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


5. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.

  1. Wipe the oil pan and oil pan drain plug.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }


6. REMOVE TRANSMISSION OIL LEVEL GAUGE SUB-ASSEMBLY (for Automatic Transmission)

  1. C101767
    Remove the transmission oil level gauge sub-assembly from the transmission oil filler tube sub-assembly.


7. DRAIN MANUAL TRANSMISSION OIL (for Manual Transmission)
  1. Remove the filler plug and gasket.

  1. Remove the drain plug and gasket, and drain the oil.

  1. Install the drain plug with a new gasket.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


8. DRAIN AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)

  1. C158131E01
    Remove the drain plug and gasket and drain automatic transmission fluid.

  1. Install the drain plug with a new gasket.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


9. REMOVE FRONT SEAT ASSEMBLY RH

  1. B107528
    Move the front seat assembly fully forward.

  1. Remove the 2 bolts on the rear side of the seat.

  1. Move the front seat assembly to the rearmost position.

  1. Remove the 2 bolts on the front side of the seat.

  1. Move the front seat assembly to the center of the seat slide rail. Set the seatback in the upright position.

  1. Disconnect the front seat inner belt assembly connector.

  1. Remove the front seat assembly.


10. REMOVE FRONT DOOR SCUFF PLATE RH

11. REMOVE ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY
  1. Roll up the carpet and remove the engine service hole sub cover.


12. REMOVE NO. 2 ENGINE SERVICE HOLE COVER
  1. Detach the clips and fold back the carpet.

  1. A151559
    Remove the 3 bolts and No. 2 engine service hole cover.


13. REMOVE GENERATOR ASSEMBLY
(Click here)

14. REMOVE FRONT EXHAUST PIPE ASSEMBLY
(Click here)

15. REMOVE TURBOCHARGER SUB-ASSEMBLY
(Click here)

16. REMOVE EXHAUST MANIFOLD

  1. A239347
    Remove the 8 nuts, 8 plate washers, 8 collars and exhaust manifold.


17. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET

  1. A264145
    Remove the 4 bolts and No. 1 compressor mounting bracket.


18. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

  1. A264146
    Remove the 4 bolts and V-ribbed belt tensioner.


19. DISCONNECT NO. 1 RADIATOR HOSE
  1. Disconnect the No. 1 radiator hose from the water inlet.


20. DISCONNECT HEATER HOSE

  1. A239342
    Disconnect the heater hose from the water by-pass pipe.


21. DISCONNECT NO. 3 WATER BY-PASS HOSE

  1. A239335
    Detach the clamp and disconnect the No. 3 water by-pass hose from the No. 2 water by-pass pipe.


22. DISCONNECT OIL RETURN HOSE

  1. A239336
    Detach the 2 clamps and disconnect the oil return hose from the intake manifold.


23. REMOVE NO. 4 AIR HOSE

  1. A231914
    Loosen the 2 hose clamps.

  1. Remove the No. 4 air hose.


24. DISCONNECT NO. 4 RADIATOR HOSE

  1. A239337
    Remove the No. 4 radiator hose from the water outlet.


25. DISCONNECT NO. 2 FUEL HOSE

  1. A263232
    Disconnect the No. 2 fuel hose from the No. 3 nozzle leakage pipe.


26. DISCONNECT NO. 1 FUEL HOSE

  1. A263233
    Disconnect the No. 1 fuel hose from the fuel supply pump.


27. DISCONNECT VACUUM HOSE

  1. A239332
    Disconnect the vacuum hose from the vacuum pump.


28. DISCONNECT ENGINE WIRE

  1. A317701
    Remove the bolt.

  1. Detach the clamp to disconnect the engine wire.

  1. A314923
    Disconnect the ECM connector (Click here).

  1. Disconnect the 5 connectors.

  1. Detach the 5 clamps.


29. DISCONNECT ENGINE ROOM MAIN WIRE

  1. A239344
    Disconnect the 5 connectors.

  1. A239345
    Open the cover and remove the nut.

  1. A239343
    Detach the clamp and disconnect the engine room main wire.


30. DISCONNECT VANE PUMP OIL RESERVOIR ASSEMBLY

  1. A231913
    Remove the 2 bolts and disconnect the vane pump oil reservoir.


31. REMOVE PROPELLER SHAFT ASSEMBLY

  1. C102185E01
    Put matchmarks on both flanges.

  1. Remove the 4 nuts, bolts and washers.

    HINT:
    If the flange connection is hard to separate, temporarily tighten one nut only and evenly tap the flange with a brass bar and hammer to separate the propeller shaft assembly from the differential companion flange.

  1. Remove the propeller shaft assembly.

  1. C102186E01
    Insert SST in the transmission to prevent oil leakage.

    NOTICE:
    Do not damage the oil seal.


    1. Use the following SST for the automatic transmission

      SST
      09325-40010  

    2. Use the following SST for the manual transmission

      SST
      09325-20010  


32. REMOVE MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission)
(Click here)

33. REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT (for Automatic Transmission)

  1. C101778E02
    Remove the bolt and drive plate cover from the automatic transmission assembly.

  1. C101779
    Turn the crankshaft pulley and remove the 6 drive plate and torque converter clutch setting bolts.


34. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
(Click here)

35. REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)

  1. C114267E01
    Put matchmarks on the clutch cover assembly and the flywheel sub-assembly.

  1. Loosen each set bolt one turn at a time until spring tension is released.

  1. Remove the set bolts, and pull off the clutch cover assembly.

    NOTICE:
    Do not drop the clutch disc assembly.


36. REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)

NOTICE:
Keep the lining part of the clutch disc assembly, the pressure plate and surface of the flywheel sub-assembly away from oil and foreign matter.


37. REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

  1. A072851E02
    Using SST, hold the crankshaft pulley.
    SST
    09213-58014  
    09330-00021  

  1. A114803
    Remove the 8 bolts and flywheel.


38. REMOVE PUMP IMPELLER DRIVE PLATE (for Automatic Transmission)

  1. A072851E02
    Using SST, hold the crankshaft pulley.
    SST
    09213-58014  
    09330-00021  

  1. A114804
    Remove the 8 bolts, rear drive plate spacer, pump impeller drive plate and flywheel.


39. REMOVE REAR END PLATE
  1. Remove the bolt and rear end plate.


40. DISCONNECT FRONT SPEED SENSOR LH

  1. C102281E01
    Remove the 2 bolts, and separate the speed sensor from the steering knuckle.

    NOTICE:
    1. Be careful not to damage the speed sensor.
    2. Prevent foreign matter from adhering to the speed sensor.


41. DISCONNECT FRONT DISC BRAKE CALIPER ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.


42. DISCONNECT FRONT SUSPENSION ARM SUB-ASSEMBLY UPPER LH

  1. C101998E01
    Remove the cotter pin and loosen the nut.
    SST
    09628-62011  

    NOTICE:
    Do not remove the nut.

  1. Using SST, separate the steering knuckle from the suspension upper arm and remove the nut.

    NOTICE:
    1. Fix the steering knuckle with a wire so that the flexible hose does not receive excessive force.
    2. Do not damage the ball joint dust cover.


43. DISCONNECT FRONT SUSPENSION ARM SUB-ASSEMBLY UPPER RH

HINT:
Use the same procedure described for the LH side.


44. DISCONNECT FRONT SHOCK ABSORBER ASSEMBLY LH

  1. C102009E02
    Remove the bolt and separate the front shock absorber from the front suspension lower arm.


45. DISCONNECT FRONT SHOCK ABSORBER ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.


46. DISCONNECT STEERING TORQUE SHAFT ASSEMBLY

  1. C106142E01
    Loosen bolt (A) and remove bolt (B), then slide the steering torque shaft assembly.

    HINT:
    1. Do not remove bolt (A).
    2. Do not disconnect the steering torque shaft assembly from the power steering link assembly.

  1. C106143E01
    Put matchmarks on the steering torque shaft assembly and the power steering link assembly.

  1. Separate the steering torque shaft assembly from the power steering link assembly.


47. REMOVE ENGINE ASSEMBLY
  1. Set an engine lifter in place.

  1. A101144J06
    Remove the 16 bolts shown in the illustration.

  1. Operate the engine lifter and slowly remove the engine from the vehicle.


48. INSTALL ENGINE HANGERS

  1. A239319E02
    Install a No. 1 engine hanger and No. 2 engine hanger with 2 bolts as shown in the illustration.

    Torque:
    for upper No. 1 engine hanger:
    25 N*m{ 255 kgf*cm }
    for No. 2 engine hanger:
    60 N*m{ 612 kgf*cm }

    Text in Illustration 
    *1
    Upper No. 1 Engine Hanger
    *2
    No. 2 Engine Hanger

    NOTICE:
    Install the engine hangers with new bolts.

    HINT:
    Upper No. 1 Engine Hanger
    12284-30020
    No. 2 Engine Hanger
    12282-67030
    Bolt
    91552-81025 and 91642-81030

  1. Attach an engine sling device and hang the engine with a chain block.


49. DISCONNECT NO. 1 OIL RESERVOIR TO PUMP HOSE

  1. C101370E01
    Remove the clip and separate the No.1 oil reservoir to pump hose.


50. DISCONNECT PRESSURE FEED TUBE ASSEMBLY

  1. C101371E01
    Remove the union bolt and separate the pressure feed tube assembly.


51. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
  1. Remove the 4 bolts and front suspension crossmember.


52. REMOVE FRONT ENGINE MOUNTING INSULATOR
  1. Remove the 2 nuts, 2 engine mounting stabilizers and 2 front engine mounting insulators.


53. INSTALL ENGINE STAND
  1. Install the engine to an engine stand with the bolts.

  1. Remove the engine sling device and chain block.

  1. Remove the 2 bolts and 2 engine hangers.


54. REMOVE ENGINE WIRE
  1. Remove the engine wire from the engine.


55. REMOVE VANE PUMP ASSEMBLY

  1. C101372E01
    Remove the 2 nuts and the vane pump assembly.

  1. Remove the vane pump O-ring from the vane pump assembly.


56. REMOVE VACUUM PUMP ASSEMBLY

  1. A102102
    Remove the 2 nuts, vacuum pump and 2 O-rings.


57. REMOVE TIMING BELT
(Click here)

58. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

  1. A070696E01
    Using a 10 mm hexagon wrench, remove the bolt, No. 1 timing belt idler and washer.


59. REMOVE ENGINE COOLANT TEMPERATURE SENSOR
  1. Disconnect the engine coolant temperature sensor connector.

  1. A239516E01
    Using SST, remove the engine coolant temperature sensor and gasket.
    SST
    09817-33190  


60. REMOVE CRANKSHAFT POSITION SENSOR

  1. TYPE A:

    A307644E01

    Text in Illustration 
    *1
    Clamp
    *2
    Wire Harness Clamps (A)
    *3
    Wire Harness Clamps (B)
    *4
    Wire Harness Clamps (C)

    1. Detach the 2 wire harness clamps (B, C).

    2. Disconnect the crankshaft position sensor connector.

    3. Detach the crankshaft position sensor connector from the No. 1 vacuum transmitting pipe.

    4. Remove the clamp.

      NOTICE:
      1. Make sure that no portion of the clamp remains in the clamp installation hole. If there is any portion of the clamp remaining, remove it.
      2. Do not reuse the clamp.

    5. Remove the bolt and crankshaft position sensor.

    6. Remove the wire harness clamp (A) from the crankshaft position sensor.

  1. TYPE B:

    A307359E01

    Text in Illustration 
    *1
    Clamp
    *2
    Bracket (Clamp)
    *3
    Wire Harness Clamps (A)
    *4
    Wire Harness Clamps (B)
    *5
    Wire Harness Clamps (C)
    -
    -

    1. Detach the 2 wire harness clamps (B, C).

    2. Disconnect the crankshaft position sensor connector.

    3. Detach the crankshaft position sensor connector from the No. 1 vacuum transmitting pipe.

    4. Remove the clamp.

      NOTICE:
      1. Make sure that no portion of the clamp remains in the clamp installation hole. If there is any portion of the clamp remaining, remove it.
      2. Do not reuse the clamp.

    5. Remove the bolt and bracket (clamp).

    6. Remove the bolt and crankshaft position sensor.

    7. Remove the wire harness clamp (A) from the crankshaft position sensor.

    8. Detach the 2 wire harness clamps from the bracket (clamp).


61. REMOVE CAMSHAFT POSITION SENSOR

A102283
  1. Disconnect the camshaft position sensor connector.

  1. Remove the bolt and the camshaft position sensor.


62. REMOVE OIL PRESSURE SWITCHING VALVE ASSEMBLY

  1. A231906
    Disconnect the oil pressure switching valve connector.

  1. Remove the bolt and oil pressure switching valve.


63. REMOVE DIESEL THROTTLE BODY ASSEMBLY

  1. w/o DPF:

    1. A177101
      Disconnect the diesel turbo pressure sensor connector and vacuum switching valve connector.

    2. Remove the bolt and disconnect the wire harness clamp.

  1. Disconnect the 2 diesel throttle body connectors.

  1. A257142E01
    Remove the 2 bolts, 2 nuts, diesel throttle body and gasket.


64. REMOVE COMMON RAIL ASSEMBLY
(Click here)

65. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY
(Click here)

66. REMOVE EGR COOLER ASSEMBLY
(Click here)

67. REMOVE GLOW PLUG ASSEMBLY
(Click here)

68. REMOVE FUEL SUPPLY PUMP ASSEMBLY
(Click here)

69. REMOVE CRANKSHAFT PULLEY

  1. A142434E01
    Using SST, hold the crankshaft pulley and loosen the pulley bolt.
    SST
    09213-58014  
    09330-00021  

  1. A142416E01
    Using SST, remove the pulley bolt and crankshaft pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)


70. REMOVE NO. 5 WATER BY-PASS PIPE SUB-ASSEMBLY

  1. A264143
    Disconnect the water hose from the No. 2 water by-pass hose.

  1. Remove the 2 bolts, nut and No. 5 water by-pass pipe.


71. REMOVE NO. 2 WATER BY-PASS PIPE

  1. A264144
    Remove the bolt, nut, No. 2 water by-pass pipe and gasket.


72. REMOVE WATER INLET

  1. A263722
    Remove the 3 bolts and water inlet.


73. REMOVE INTAKE MANIFOLD STAY

  1. A262840E01
    Remove the 2 bolts and manifold stay.
    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF


74. REMOVE NO. 1 INTAKE MANIFOLD INSULATOR
  1. Remove the No. 1 intake manifold insulator from the intake manifold.


75. REMOVE INTAKE MANIFOLD

  1. A239322
    Remove the 7 bolts, 2 nuts and intake manifold.

  1. Remove the gasket.


76. REMOVE VACUUM SWITCHING VALVE SET

  1. A265825
    Remove the 2 connectors and 3 vacuum hoses.

  1. A265826
    Remove the 2 bolts and vacuum control valve set.


77. REMOVE SWIRL CONTROL VALVE ASSEMBLY

  1. A239323
    Remove the 4 bolts, 2 nuts and swirl control valve.

  1. Remove the gasket.


78. REMOVE NO. 3 FUEL PIPE

79. REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY
  1. Disconnect the vacuum hose.

  1. Remove the bolt, nut and No. 1 vacuum transmitting pipe.


80. REMOVE NO. 2 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY
  1. Remove the bolt, 2 nuts and No. 2 vacuum transmitting pipe.


81. REMOVE OIL COOLER COVER SUB-ASSEMBLY
(Click here)

82. REMOVE WATER OUTLET
  1. Remove the 2 bolts, water outlet and gasket.


83. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH

  1. A263613
    Remove the 4 bolts and front No. 1 engine mounting bracket LH.


84. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH

  1. A263614
    Remove the 4 bolts and front No. 1 engine mounting bracket RH.

← REMOVAL (Jan 2017 – Nov 2017)INSPECTION (from Oct 2014) →