TEST MODE PROCEDURE
Troubleshooting · Vehicles built Apr 2016 – Dec 2016
Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
| WARNING LIGHT AND INDICATOR LIGHT INITIAL CHECK |
Release the parking brake.
- NOTICE:
- When releasing the parking brake, move the shift lever to P (for Automatic Transmission) or set chocks (for Manual Transmission) to prevent the vehicle from rolling.
- HINT:
- When the parking brake is applied or the brake fluid level is low, the brake warning light comes on.
When the ignition switch is turned to ON, check that the ABS warning, brake warning, VSC OFF indicator, TRC OFF indicator and slip indicator lights come on for approximately 3 seconds.
- HINT:
- If the skid control ECU (brake actuator assembly) stores any DTCs, the ABS warning and slip indicator lights will come on.
- If any of the indicators remain on or do not come on, proceed to troubleshooting for the light circuits listed below.
- If the skid control ECU (brake actuator assembly) stores any DTCs, the ABS warning and slip indicator lights will come on.
Trouble Area
See Procedure
ABS warning light circuit (Remains on)
Click here
ABS warning light circuit (Does not come on)
Click here
Brake warning light circuit (Remains on)
Click here
Brake warning light circuit (Does not come on)
Click here
VSC OFF indicator light circuit (Remains on)
Click here
VSC OFF indicator light circuit (Does not come on)
Click here
TRC OFF indicator light circuit (Remains on)
Click here
TRC OFF indicator light circuit (Does not come on)
Click here
Slip indicator light circuit (Remains on)
Click here
Slip indicator light circuit (Does not come on)
Click here
| ACTIVATE TEST MODE (SIGNAL CHECK) (When Using GTS) |
- HINT:
- VSC does not operate in Test Mode (signal check), regardless of whether the sensor check is normal or abnormal.
- When a malfunction occurs in an ABS system sensor, the ABS warning light illuminates.
- When a malfunction occurs in a VSC system sensor, the slip indicator light illuminates.
- VSC does not operate in Test Mode (signal check), regardless of whether the sensor check is normal or abnormal.
Procedure to enter Test Mode (signal check).
Turn the ignition switch off.
Check that the steering wheel is in the straight-ahead position.
for Automatic Transmission:
Check that the shift lever is in P and apply the parking brake.
for Manual Transmission:
Check that the shift lever is in neutral and apply the parking brake.Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Switch the skid control ECU (brake actuator assembly) to Test Mode using the GTS.
Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Signal Check.- HINT:
- Signals related to the VSC system can be inspected by performing a Test Mode (signal check) inspection. During the inspection, the display of items determined normal by the skid control ECU (brake actuator assembly) changes from incomplete to complete.
Test Mode (Signal Check) Inspection Item Chart Item Name
Range
Judgment Description
Trouble Area
Output Signal of Front Speed Sensor RH
Incomplete/complete
Check for foreign matter, evaluate the gap between the sensor and rotor
- Open or short in speed sensor
- Open or short in sensor system wire harness
- Defective connector contact or increased terminal resistance
- Speed sensor installation defect
- Sensor rotor system malfunction
Output Signal of Front Speed Sensor LH
Incomplete/complete
Check for foreign matter, evaluate the gap between the sensor and rotor
- Open or short in speed sensor
- Open or short in sensor system wire harness
- Defective connector contact or increased terminal resistance
- Speed sensor installation defect
- Sensor rotor system malfunction
Output Signal of Rear Speed Sensor RH
Incomplete/complete
Check for foreign matter, evaluate the gap between the sensor and rotor
- Open or short in speed sensor
- Open or short in sensor system wire harness
- Defective connector contact or increased terminal resistance
- Speed sensor installation defect
- Sensor rotor system malfunction
Output Signal of Rear Speed Sensor LH
Incomplete/complete
Check for foreign matter, evaluate the gap between the sensor and rotor
- Open or short in speed sensor
- Open or short in sensor system wire harness
- Defective connector contact or increased terminal resistance
- Speed sensor installation defect
- Sensor rotor system malfunction
Change in Output Signal of Front Speed Sensor RH
Incomplete/complete
- Evaluate the stability of the sensor input waveform
- Evaluate the straight ahead / reverse signal inputs
- Foreign object attached to speed sensor
- Sensor rotor system malfunction
Change in Output Signal of Front Speed Sensor LH
Incomplete/complete
- Evaluate the stability of the sensor input waveform
- Evaluate the straight ahead / reverse signal inputs
- Foreign object attached to speed sensor
- Sensor rotor system malfunction
Change in Output Signal of Rear Speed Sensor RH
Incomplete/complete
- Evaluate the stability of the sensor input waveform
- Evaluate the straight ahead / reverse signal inputs
- Foreign object attached to speed sensor
- Sensor rotor system malfunction
Change in Output Signal of Rear Speed Sensor LH
Incomplete/complete
- Evaluate the stability of the sensor input waveform
- Evaluate the straight ahead / reverse signal inputs
- Foreign object attached to speed sensor
- Sensor rotor system malfunction
Output Voltage in Deceleration Sensor
Incomplete/complete
Evaluate the acceleration sensor output voltage
- Acceleration sensor zero point stored incorrectly
- Acceleration sensor (airbag sensor assembly) connector connection malfunction
- Acceleration sensor (airbag sensor assembly) internally stuck
- Defective acceleration sensor (airbag sensor assembly) installation
Memory of System Information
Incomplete/complete
Evaluate stored system information (skid control ECU (brake actuator assembly)) against vehicle specification
- ECM incorrectly installed
- Brake actuator assembly incorrectly installed
- CAN communication between ECM and skid control ECU (brake actuator assembly)
Output in Master Cylinder Pressure Sensor
Incomplete/complete
- Evaluate the master cylinder pressure sensor zero point voltage
- Check that the sensitivity of the master cylinder pressure sensor is normal
- Open circuit or short in master cylinder pressure sensor circuit
- Open or short in stop light switch assembly circuit or defective connector connection
- Stop light switch assembly stuck OFF
| ACTIVATE TEST MODE (SIGNAL CHECK) (When Using SST Check Wire) |
- HINT:
- VSC does not operate in Test Mode (signal check), regardless of whether the sensor check is normal or abnormal.
- When a malfunction occurs in an ABS system sensor, the ABS warning light illuminates.
- When a malfunction occurs in a VSC system sensor, the slip indicator light illuminates.
- VSC does not operate in Test Mode (signal check), regardless of whether the sensor check is normal or abnormal.
Procedure to enter Test Mode (signal check).
Turn the ignition switch off.
Check that the steering wheel is in the straight-ahead position.
for Automatic Transmission:
Check that the shift lever is in P and apply the parking brake.
for Manual Transmission:
Check that the shift lever is in neutral and apply the parking brake.
Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.

- SST
- 09843-18040
Text in Illustration *a
Front view of DLC3
Turn the ignition switch to ON.
Check that the ABS warning and slip indicator lights come on for several seconds and then blink in Test Mode (signal check).
- HINT:
- If the ABS warning and slip indicator lights do not blink, inspect the TS and CG terminal circuit and ABS warning and slip indicator light circuits.
Trouble Area
See Procedure
TS and CG terminal circuit
Click here
ABS warning light circuit (Remains on)
Click here
ABS warning light circuit (Does not come on)
Click here
Slip indicator light circuit (Remains on)
Click here
Slip indicator light circuit (Does not come on)
Click here
| ACCELERATION SENSOR CHECK |
Enter Test Mode (signal check).
Keep the vehicle stationary on a level surface for 1 second or more.
- HINT:
- The acceleration sensor check can be performed with the master cylinder pressure sensor check below.
| MASTER CYLINDER PRESSURE SENSOR CHECK |
Enter Test Mode (signal check).
Start the engine.
Leave the vehicle in a stationary condition and release the brake pedal for 1 second or more, and quickly and continuously depress the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more for 1 second.
Check that the ABS warning light stays on for 3 seconds.
- HINT:
- Ensure that the ABS warning light comes on.
- While the ABS warning light stays on, continue to depress the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more.
- The ABS warning light comes on for 3 seconds every time the brake pedal operation above is performed.
- If the master cylinder pressure sensor check is not completed, depressing the brake pedal causes further decreases in vacuum in the brake booster, making the sensor check difficult to complete.
- If the vacuum is insufficient, the master cylinder pressure sensor check may not be completed. In this case, run the engine at idle to obtain sufficient vacuum.
- If the brake pedal is strongly depressed when the vacuum is insufficient, the brake warning light may come on in accordance with booster pressure control. In this case, run the engine at idle to obtain sufficient vacuum.
- Ensure that the ABS warning light comes on.
| SPEED SENSOR CHECK |
- NOTICE:
- Before performing the speed sensor signal check, complete the acceleration sensor and master cylinder pressure sensor checks.
Enter Test Mode (signal check).
Start the engine.
Drive the vehicle straight ahead.
Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds and check that the ABS warning light goes off.- The sensor check may not be completed if wheelspin occurs.
- The ABS warning light blinks when the sensor check has been completed and the brake pedal is depressed.
- The ABS warning light comes on immediately after a malfunction has been detected during the speed sensor check.
- The sensor check may not be completed if wheelspin occurs.
Stop the vehicle.
- NOTICE:
- The speed sensor check may not be completed if the sensor check is started with the steering wheel turned or one or more wheels spinning.
- After the ABS warning light goes off and if the vehicle speed exceeds 80 km/h (50 mph), a sensor check code will be stored again. Decelerate or stop the vehicle before the speed reaches 80 km/h (50 mph).
- If the sensor check has not been completed, the ABS warning light blinks during driving and the ABS system does not operate.
- The speed sensor check may not be completed if the sensor check is started with the steering wheel turned or one or more wheels spinning.
- HINT:
- When the sensor check has been completed, the ABS warning light remains off during driving and blinks in the Test Mode (signal check) pattern while the vehicle is stationary.
| END OF SENSOR CHECK |
If the sensor check is completed, the ABS warning light and slip indicator light blink (Test Mode (signal check)) when the vehicle stops and the ABS warning light is off while the vehicle is being driven.
- NOTICE:
- When using GTS:
When Test Mode (signal check) is started with the GTS and all items display complete, the sensor check ends.
- If the sensor check is not complete, the ABS warning light blinks when the vehicle is in motion and the ABS does not operate.
- If a DTC is detected in Test Mode (signal check), the ABS warning light or slip indicator light illuminates.
- When using GTS:
| END OF TEST MODE (SIGNAL CHECK) |
End Test Mode (signal check) using the GTS
Turn the ignition switch off and enter normal mode.
Remove the GTS.
End Test Mode (signal check) by connecting DLC3 terminals
Turn the ignition switch off and disconnect terminals 13 (TC), 12 (TS) and 4 (CG) of the DLC3.
Turn the ignition switch to ON.
- HINT:
- Test Mode (signal check) is continued if 12 (TS) and 4 (CG) are disconnected while the ignition switch is ON.
- If the ignition switch is turned to ON with terminals 12 (TS) and 4 (CG) connected, the previous Test Mode (signal check) is maintained.
- Test Mode (signal check) is continued if 12 (TS) and 4 (CG) are disconnected while the ignition switch is ON.