3.
REMOVE ENGINE UNDER COVER NO.1 (w/ Engine Under Cover No.1)
4.
REMOVE ENGINE UNDER COVER NO.2 (w/ Engine Under Cover No.2)
5.
REMOVE ENGINE SIDE UNDER COVER LH (w/ Engine Side Under Cover LH)
6.
REMOVE ENGINE SIDE UNDER COVER RH (w/ Engine Side Under Cover RH)
7.
DRAIN ENGINE COOLANT
CAUTION:
Do not remove the radiator reservoir cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
HINT:
Collect the engine coolant in a container and dispose of it according to local regulations.
Loosen the radiator drain cock plug and drain the engine coolant.
Text in Illustration
*A
w/ Dual VVT-i
*B
w/o Dual VVT-i
*1
Radiator Reservoir Cap Sub-assembly
*2
Radiator Reservoir Assembly
*3
Radiator Drain Cock Plug
*4
Cylinder Block Water Drain Cock Plug
*5
2-Way
-
-
Remove the radiator reservoir cap sub-assembly.
Loosen the cylinder block water drain cock plug and drain the engine coolant from the engine.
8.
DRAIN ENGINE OIL
Remove the oil filler cap.
Remove the oil drain plug and drain the engine oil from the oil pan sub-assembly.
NOTICE:
Collect the oil in a disposable oil container.
Clean the oil pan drain plug and install it with a new gasket.
Torque:
38 N*m{
382 kgf*cm
, 28 ft.*lbf
}
9.
REMOVE FRONT SEAT ASSEMBLY RH (for Hi-back Seat Type)
Perform the same procedure as above on the opposite side. (Click here)
10.
REMOVE FRONT SEAT ASSEMBLY RH (for Low-back Seat Type)
Perform the same procedure as above on the opposite side. (Click here)
11.
REMOVE FRONT DOOR SCUFF PLATE RH
12.
REMOVE ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY
Roll up the carpet, and remove the 5 bolts and engine service hole sub cover.
13.
REMOVE FAN & GENERATOR V BELT
Use the hexagon-shaped part indicated by the arrow in the illustration to move the tensioner pulley downward and decrease the tension in the drive belt. Then remove the drive belt.
NOTICE:
When removing the drive belt, do not use the idle pulley's bolt.
HINT:
After removing the drive belt, move the tensioner upward to the maximum amount.
14.
DISCONNECT RADIATOR HOSE INLET
Remove the clamp, and disconnect the radiator hose inlet from the engine.
15.
DISCONNECT RADIATOR HOSE OUTLET
Remove the clamp, and disconnect the radiator hose outlet from the engine.
16.
DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY
Disconnect the fuel vapor feed hose from the VSV.
17.
DISCONNECT UNION TO CONNECTOR TUBE HOSE
Disconnect the union to connector tube hose from the intake manifold.
18.
REMOVE INTAKE AIR CONNECTOR
Slide the clamp and disconnect the No. 2 ventilation hose from the cylinder head cover sub-assembly.
Disconnect the vacuum hose from the intake air connector.
Loosen the 2 hose clamps.
Remove the 2 bolts and intake air connector.
19.
DISCONNECT FUEL HOSE
Disconnect the No. 1 fuel hose from the fuel pressure pulsation damper assembly (Click here).
20.
DISCONNECT FUEL HOSE NO.2
Remove the clamp, and disconnect the fuel hose No.2 from the delivery pipe.
21.
DISCONNECT VANE PUMP ASSEMBLY
Disconnect the PS fluid pressure switch connector.
Remove the 2 bolts and disconnect the pump from the engine.
Support the vane pump securely.
22.
REMOVE OIL LEVEL GAUGE SUB-ASSEMBLY
23.
REMOVE OIL LEVEL GAUGE GUIDE
Remove the bolt and gauge guide.
24.
DISCONNECT COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System)
Disconnect the compressor connector.
Remove the 4 bolts and disconnect the compressor from the engine.
HINT:
Disconnect the compressor with the low pressure hose and high pressure hose stuck by suspended from the rope.
Support the cooler compressor securely.
25.
DISCONNECT ENGINE WIRE
26.
REMOVE THROTTLE WITH MOTOR BODY ASSEMBLY
Disconnect the throttle motor connector.
Text in Illustration
*A
w/ Dual VVT-i
*B
w/o Dual VVT-i
Slide the clamp and disconnect the water by-pass hose from the throttle body assembly.
Slide the clamp and disconnect the No. 2 water by-pass hose from the throttle body assembly.
Remove the 4 bolts and throttle body assembly.
Remove the gasket from the intake manifold.
27.
REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY
NOTICE:
Be careful not to drop the fuel injector assemblies when removing the fuel delivery pipe sub-assembly.
Disconnect the vacuum hose from the fuel pressure regulator assembly.
Slide the clamp and disconnect the No. 2 fuel hose from the fuel pressure regulator assembly.
Disconnect the 4 fuel injector connectors.
Text in Illustration
*A
w/ Dual VVT-i
*B
w/o Dual VVT-i
Remove the 2 bolts, fuel pulsation damper assembly and O-ring.
Remove the 2 bolts and fuel delivery pipe sub-assembly together with the 4 fuel injector assemblies.
NOTICE:
Be careful not to drop the fuel injector assemblies when removing the fuel delivery pipe sub-assembly.
Remove the 2 No. 1 delivery pipe spacers from the cylinder head sub-assembly.
Remove the 4 injector vibration insulators.
Using a screwdriver, pry out the 4 injector spacers and 4 O-rings from the cylinder head sub-assembly.
Text in Illustration
*A
w/ Dual VVT-i
*B
w/o Dual VVT-i
*a
Protective Tape
HINT:
Tape the screwdriver tip before use.
28.
REMOVE INJECTOR ASSEMBLY
Pull out the 4 fuel injector assemblies from the fuel delivery pipe sub-assembly.
Text in Illustration
*A
w/ Dual VVT-i
*B
w/o Dual VVT-i
Pull Out
Remove the O-rings from the fuel injector assemblies.
29.
REMOVE INTAKE MANIFOLD
Disconnect the ventilation hose No.3.
Remove the 5 bolts, 2 nuts, intake manifold and gasket.
30.
REMOVE FAN PULLEY
Remove the 4 nuts, fan pulley and fan spacer.
31.
REMOVE WATER BY-PASS PIPE NO.1
Remove the bolt, 2 nuts, water by-pass pipe and gasket.
32.
REMOVE GENERATOR ASSEMBLY
Disconnect the generator connector.
Remove the terminal cap.
Remove the nut and disconnect the wire harness from terminal B.
Remove the 3 bolts and generator assembly.
33.
REMOVE COMPRESSOR MOUNTING BRACKET NO.1 (w/ Air Conditioning System)
Remove the 5 bolts and compressor mounting bracket No.1.
34.
REMOVE IDLER PULLEY SUB-ASSEMBLY NO.1
Remove the bolt, pulley plate, collar, and idler pulley sub-assembly No.1.
35.
REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
Remove the 2 bolts and belt tensioner.
36.
REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY (for Manual Transmission)
38.
REMOVE AIR PRESSURE SENSOR (w/ Manifold Absolute Pressure Sensor)
Disconnect the connector.
Disconnect the vacuum hose and clamp.
Detach the wire harness clamp
Remove the 2 bolts and air pressure sensor together with the bracket.
Remove the bolt and air pressure sensor.
39.
REMOVE IGNITION COIL ASSEMBLY
Remove the bolts and ignition coil assembly.
40.
REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
Disconnect the ventilation hose No.1.
Remove the 19 bolts, 2 nuts, head cover and 2 gaskets.
Remove the cylinder head cover gasket and cylinder head cover No.2 from the cylinder head cover.
41.
REMOVE CRANKSHAFT PULLEY
Set No.1 cylinder to TDC/compression.
Turn the crankshaft pulley, and align its groove with timing mark 0 of the timing chain cover.
Check that the timing marks of the camshaft timing gear and sprocket are aligned with the timing marks of bearing cap No.1, as shown in the illustration.
HINT:
If not, turn the crankshaft pulley 1 revolution (360°) and align the marks as shown above.
Using SST, loosen the pulley bolt.
SST
09213-54015
(91651-60855)
09330-00021
Using SST, remove the pulley bolt and pulley.
HINT:
Apply grease to the thread and tip of the SST (center bolt) prior to use.
Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and No. 2 oil pan sub-assembly. Cut through the applied sealer and remove the No. 2 oil pan sub-assembly.
NOTICE:
Be careful not to damage the contact surfaces of the oil pan sub-assembly and No. 2 oil pan sub-assembly.
43.
REMOVE OIL PAN SUB-ASSEMBLY
Remove the 16 bolts and 2 nuts.
Using a screwdriver wrapped in protective tape, remove the oil pan sub-assembly by prying between the oil pan sub-assembly and cylinder block sub-assembly as shown in the illustration.
Text in Illustration
*a
Protective Tape
NOTICE:
Be careful not to damage the contact surfaces of the cylinder block sub-assembly and oil pan sub-assembly.
HINT:
Tape the screwdriver tip before use.
Remove the gasket.
44.
REMOVE OIL STRAINER SUB-ASSEMBLY
Remove the 6 bolts and oil strainer sub-assembly.
45.
REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY