2014-2019 Hiace · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Apr 2016

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 from Apr 2016

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. After removing the injection pipes, clean them with a brush and compressed air.


1. REMOVE ENGINE ASSEMBLY
(Click here)

2. INSTALL ENGINE STAND
  1. Install the engine to an engine stand with the bolts.

  1. Remove the engine sling device and chain block.

  1. Remove the 2 bolts and 2 engine hangers.


3. REMOVE VANE PUMP ASSEMBLY

  1. C101372E01
    Remove the 2 nuts and the vane pump assembly.

  1. Remove the vane pump O-ring from the vane pump assembly.


4. REMOVE VACUUM PUMP ASSEMBLY

  1. C101372E01
    Remove the 2 nuts and the vane pump assembly.

  1. Remove the vane pump O-ring from the vane pump assembly.


5. REMOVE TIMING BELT
(Click here)

6. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

  1. A070696E01
    Using a 10 mm hexagon wrench, remove the bolt, No. 1 timing belt idler and washer.


7. REMOVE CRANKSHAFT POSITION SENSOR

  1. TYPE A:

    A307644E01

    Text in Illustration 
    *1
    Clamp
    *2
    Wire Harness Clamps (A)
    *3
    Wire Harness Clamps (B)
    *4
    Wire Harness Clamps (C)

    1. Detach the 2 wire harness clamps (B, C).

    2. Disconnect the crankshaft position sensor connector.

    3. Detach the crankshaft position sensor connector from the No. 1 vacuum transmitting pipe.

    4. Remove the clamp.

      NOTICE:
      1. Make sure that no portion of the clamp remains in the clamp installation hole. If there is any portion of the clamp remaining, remove it.
      2. Do not reuse the clamp.

    5. Remove the bolt and crankshaft position sensor.

    6. Remove the wire harness clamp (A) from the crankshaft position sensor.

  1. TYPE B:

    A307359E01

    Text in Illustration 
    *1
    Clamp
    *2
    Bracket (Clamp)
    *3
    Wire Harness Clamps (A)
    *4
    Wire Harness Clamps (B)
    *5
    Wire Harness Clamps (C)
    -
    -

    1. Detach the 2 wire harness clamps (B, C).

    2. Disconnect the crankshaft position sensor connector.

    3. Detach the crankshaft position sensor connector from the No. 1 vacuum transmitting pipe.

    4. Remove the clamp.

      NOTICE:
      1. Make sure that no portion of the clamp remains in the clamp installation hole. If there is any portion of the clamp remaining, remove it.
      2. Do not reuse the clamp.

    5. Remove the bolt and bracket (clamp).

    6. Remove the bolt and crankshaft position sensor.

    7. Remove the wire harness clamp (A) from the crankshaft position sensor.

    8. Detach the 2 wire harness clamps from the bracket (clamp).


8. REMOVE CAMSHAFT POSITION SENSOR

A102283
  1. Disconnect the camshaft position sensor connector.

  1. Remove the bolt and the camshaft position sensor.


9. REMOVE OIL PRESSURE SWITCHING VALVE ASSEMBLY

  1. A231906
    Disconnect the oil pressure switching valve connector.

  1. Remove the bolt and oil pressure switching valve.


10. REMOVE DIESEL THROTTLE BODY ASSEMBLY
(Click here)

11. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY
(Click here)

12. REMOVE EGR COOLER WITH NO. 2 EGR VALVE ASSEMBLY
(Click here)

13. REMOVE COMMON RAIL ASSEMBLY
(Click here)

14. REMOVE FUEL SUPPLY PUMP ASSEMBLY
(Click here)

15. REMOVE INJECTOR ASSEMBLY
(Click here)

16. REMOVE CAMSHAFT TIMING PULLEY

  1. A100848
    Remove the bolt of the camshaft timing pulley while holding the camshaft with a wrench.

  1. A323634E02
    Using SST, remove the camshaft timing pulley and key.
    SST
    09950-40011   (09951-04010, 09952-04010, 09953-05010, 09957-04010)
    09955-04150  
    Text in Illustration 
    *a
    Hold
    *b
    Turn

  1. A100847E05
    Rotate the crankshaft approximately 90° counterclockwise from TDC to lower the piston.


17. REMOVE NO. 2 TIMING BELT COVER

  1. A051300E01
    Remove the nut, 4 bolts and No. 2 timing belt cover.


18. REMOVE WATER PUMP ASSEMBLY

  1. A100852
    Remove the 5 bolts, 2 nuts, water pump and gasket.


19. REMOVE CRANKSHAFT PULLEY

  1. A142434E01
    Using SST, hold the crankshaft pulley and loosen the pulley bolt.
    SST
    09213-58014  
    09330-00021  

  1. A142416E01
    Using SST, remove the pulley bolt and crankshaft pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)


20. REMOVE OIL PAN SUB-ASSEMBLY

  1. A239346
    Disconnect the vinyl tube from the oil pan.

  1. A074128E02
    Remove the 22 bolts and 2 nuts.

  1. A057637E04
    w/ DPF:
    Insert the blade of an oil pan seal cutter between the oil pan and cylinder block, cut through the applied sealer, and then remove the oil pan.

    NOTICE:
    1. Do not use the oil pan seal cutter for the area between the oil pan and timing gear case, or for the area between the oil pan and rear oil seal retainer.
    2. Be careful not to damage the oil pan flange.

  1. A057637E04
    w/o DPF:
    Insert the blade of an oil pan seal cutter between the oil pan and cylinder block stiffening plate, cut through the applied sealer, and then remove the oil pan and cylinder block stiffening plate.

    NOTICE:
    1. Do not use the oil pan seal cutter for the area between the oil pan and timing gear case, or for the area between the oil pan and rear oil seal retainer.
    2. Be careful not to damage the oil pan flange.


21. REMOVE OIL STRAINER SUB-ASSEMBLY

  1. A102736
    Remove the 2 bolts, 2 nuts, oil strainer and gasket.


22. REMOVE TIMING GEAR COVER

  1. A262940E01
    Remove the 14 bolts and 2 nuts.
    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF

  1. A262941E01
    Pry the timing gear cover at the locations shown in the illustration and remove the timing gear cover.
    Text in Illustration 
    *A
    w/ DPF
    *B
    w/o DPF

    NOTICE:
    Be careful not to drop the injection gear.

  1. A239295
    w/ DPF:
    Remove the 3 O-rings from the timing gear case.

  1. A051310E01
    w/o DPF:
    Remove the O-rings from the timing gear case.


23. REMOVE TIMING GEAR CASE OIL SEAL

HINT:
There are 2 methods to remove the oil seal.

  1. If the timing gear cover is removed from the cylinder block:

    1. A058117E01
      Using a screwdriver and hammer, tap out the oil seal.

    2. A058118E02
      Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing gear cover edge.
      SST
      09223-15020  
      09502-12010  
      09950-70010   (09951-07100)

    3. Apply MP grease to the lip of the oil seal.

  1. If the timing gear cover is installed to the cylinder block:

    1. A058126E02
      Using a knife, cut through the lip of the oil seal.

    2. Using a screwdriver, pry out the oil seal.

      NOTICE:
      Be careful not to damage the crankshaft.

    3. A058127E01
      Apply MP grease to the lip of the oil seal.

    4. Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing gear cover edge.

      SST
      09223-15020  
      09502-12010  
      09950-70010   (09951-07100)


24. REMOVE TIMING GEAR COVER OIL SEAL

HINT:
There are 2 methods to remove the oil seal.

  1. If the timing gear cover is removed from the cylinder block:

    1. A058121E01
      Using a screwdriver and hammer, tap out the oil seal.

    2. A058119E01
      Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing gear cover edge.
      SST
      09214-76011  

    3. Apply MP grease to the lip of the oil seal.

  1. If the timing gear cover is installed to the cylinder block:

    1. A058124E01
      Using SST, remove the oil seal.
      SST
      09308-10010  
      09950-40011   (09957-04010)
      09950-60010   (09951-00350)

    2. A058125E01
      Apply MP grease to the lip of a new oil seal.

    3. Using SST and a hammer, tap in the oil seal until its surface is flush with the timing gear cover edge.

      SST
      09214-76011  


25. REMOVE INJECTION GEAR

  1. A102771
    Secure the No. 2 idle sub gear to the No. 1 idle gear with a service bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    If the bolt hole of the No. 2 idle sub gear is not aligned with the bolt hole of the No. 1 idle gear, rotate the crankshaft counterclockwise to align the bolt holes. Then install the service bolt.

  1. A102772
    Remove the injection gear.


26. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

  1. A102774
    Remove the No. 1 crankshaft position sensor plate.


27. REMOVE CRANKSHAFT TIMING GEAR

  1. A060156E01
    Using SST, remove the crankshaft timing gear.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)


28. REMOVE IDLE GEAR THRUST PLATE

  1. A102775
    Remove the 2 bolts and idle gear thrust plate.


29. REMOVE NO. 1 IDLE GEAR

  1. A051316E01
    Remove the No. 1 idle gear together with the No. 1 and No. 2 idle sub gears.

  1. A069830E01
    Mount the No. 1 idle gear and No. 2 idle sub gear in a vise.

    NOTICE:
    Be careful not to damage the gears.

  1. A069831E02
    Using SST, turn the No. 1 idle sub gear clockwise and remove the service bolt.
    SST
    09960-10010   (09962-01000, 09963-00600)
    Text in Illustration 
    *1
    Service Bolt

  1. A069832E01
    Using snap ring pliers, remove the shaft snap ring.

  1. A069833E03
    Remove the wave washer, No. 1 idle sub gear and idle gear spring.
    Text in Illustration 
    *1
    Wave Washer
    *2
    No. 1 Idle Sub Gear
    *3
    Idle Gear Spring

  1. A051322E01
    Remove the No. 1 idle gear and set it in a vise.

    NOTICE:
    Be careful not to damage the gear.

  1. A069834E01
    Using snap ring pliers, remove the shaft snap ring.

  1. A069835E05
    Remove the wave washer, No. 2 idle sub gear and idle gear spring.
    Text in Illustration 
    *1
    Wave Washer
    *2
    No. 2 Idle Sub Gear
    *3
    Idle Gear Spring


30. REMOVE NO. 1 IDLE GEAR SHAFT

  1. A051317E01
    Remove the No. 1 idle gear shaft.


31. REMOVE TIMING GEAR CASE ASSEMBLY

  1. A069842E01
    Remove the union bolt and 8 bolts.

  1. A102853E02
    Pry the timing gear case at the location shown in the illustration and remove the timing gear case.

  1. A051330E01
    Remove the gasket.

  1. A069840E03
    Remove the 2 O-rings.

← REMOVAL (Jan 2015 – Mar 2016)DISASSEMBLY (from Oct 2014) →