2014-2019 Hiace · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Jan 2017


1. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start up the engine.

  1. Turn the A/C switch on.

  1. Operate the cooler compressor at an engine rpm of approximately 1,000 for 5 to 6 minutes to circulate the refrigerant and collect compressor oil remaining in each component into the cooler compressor as much as possible.

  1. Stop the engine.

  1. Using SST, let the refrigerant gas out.

    SST
    07110-58060   (07117-58080, 07117-58090, 07117-78050, 07117-88060, 07117-88070, 07117-88080)


2. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap sub-assembly while the engine assembly and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Connect a hose with an inside diameter of 9 mm (0.354 in.) to the radiator drain cock.

  1. Loosen the radiator drain cock plug.

    A397672E03

    Text in Illustration 
    *1
    Bleeder Plug
    *2
    Radiator Cap Sub-assembly
    *3
    Radiator Reserve Tank Assembly
    *4
    Cylinder Block Drain Cock Plug
    *5
    Radiator Drain Cock Plug
    -
    -

  1. Remove the radiator cap sub-assembly.

  1. Loosen the cylinder block drain cock plug, and drain the engine coolant.

  1. Tighten the radiator drain cock plug.

  1. Tighten the cylinder block drain cock plug.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Disconnect the hose from the radiator drain cock.


3. REMOVE FRONT BUMPER REINFORCEMENT
(Click here)

4. REMOVE HOOD LOCK SUPPORT BRACE SUB-ASSEMBLY

  1. E289333E01
    Remove the 3 bolts and hood lock support brace sub-assembly.
    Text in Illustration 
    *A
    for Standard Body
    *B
    for Wide Body


5. REMOVE W/RECEIVER CONDENSER ASSEMBLY
(Click here)

6. REMOVE NO. 1 AIR INLET DUCT

  1. A243232
    Detach the 5 clips and remove the 2 bolts, No. 1 air inlet duct and No. 2 air inlet duct.


7. REMOVE RADIATOR RESERVE TANK ASSEMBLY

  1. A316482
    Slide the clamp and disconnect the water by-pass hose from the radiator reserve tank assembly.

  1. Slide the clamp and disconnect the No. 2 water by-pass hose from the radiator reserve tank assembly.

  1. Remove the bolt and radiator reserve tank assembly.


8. REMOVE WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY

  1. A396703
    Remove the 2 bolts and windshield washer motor and pump assembly.

  1. A396704
    Detach the hose clamp.

  1. Disconnect the 2 connectors and 2 washer hoses.


9. DISCONNECT UREA TANK FILLER PIPE ASSEMBLY

  1. A397673
    Disconnect the 2 bolts and urea tank filler pipe assembly from the upper radiator support sub-assembly.


10. REMOVE HOOD LOCK ASSEMBLY

  1. A243233
    Remove the 3 bolts and disconnect the hood lock assembly.

  1. Remove the hood lock assembly from the hood lock control cable assembly.


11. REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY
  1. Slide the hose clamp and disconnect the water by-pass hose from the radiator assembly.

  1. A396687
    Detach the 2 clamps to disconnect the hood lock control cable assembly from the upper radiator support sub-assembly.

  1. Remove the 4 bolts, 2 screws and upper radiator support sub-assembly.

    Text in Illustration 
    V100135
    Bolt
    V100136
    Screw


12. REMOVE INTERCOOLER ASSEMBLY

  1. A144608
    Loosen the hose clamp and disconnect the No. 2 air hose.

  1. Loosen the hose clamp and disconnect the No. 3 air hose.

  1. Remove the 3 bolts and intercooler.


13. DISCONNECT OIL COOLER HOSE

  1. A241038E01
    Detach the 2 clamps and disconnect the oil cooler hose from the fan shroud.

  1. Slide the 2 clamps and disconnect the 2 oil cooler hoses from the 2 oil cooler tubes.


14. REMOVE FAN BRACKET SUB-ASSEMBLY

  1. A396705
    Detach the clamp and remove the 2 bolts, 2 nuts and fan bracket sub-assembly.


15. REMOVE FAN SHROUD

  1. A396689
    Detach the 2 clamps and disconnect the 2 connectors.

  1. A241041
    Remove the 6 bolts and fan shroud from the underside of the vehicle.


16. REMOVE NO. 2 FAN SHROUD
  1. Slide the hose clamp and disconnect the No. 2 water by-pass hose from the water by-pass pipe sub-assembly.

  1. A396690
    Remove the bolt to disconnect the water by-pass pipe sub-assembly from the radiator assembly.

  1. A102971E02
    Remove the 2 bolts from the upper side of the vehicle, and then remove the No. 2 fan shroud from the underside of the vehicle.

    NOTICE:
    Do not damage the radiator assembly when removing the No. 2 fan shroud.


17. REMOVE RADIATOR ASSEMBLY
  1. Slide the 2 clamps and disconnect the No. 2 radiator hose and No. 3 radiator hose from the radiator assembly.

  1. A316610
    Remove the radiator assembly from the vehicle.

  1. Remove the 4 grommets from the radiator assembly.


18. REMOVE OIL COOLER HOSE

  1. A316639
    Slide the 2 clamps and disconnect the 2 oil cooler hoses from the radiator assembly.


19. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY

  1. A316602
    Slide the clamp and remove the water by-pass pipe sub-assembly from the radiator assembly.

← ON-VEHICLE INSPECTION (from Jan 2017)INSTALLATION (from Jan 2017) →